action figure 3d print

The case is designed to be printed with a layer height of 0.2 or 0.3mm. You can lower the height if you want more details which is recommended for the ARC reactor. Supports are needed on some parts.I used PLA on everything but the electrics carrier....

... Some part coolers like the "Petsfang" & "Bullseye" seem to crash into the camera housing during autobed leveling. Many thanks to "acwest" for pointing out that problem and his solution! ===================================== Have fun printing!

... PS: If the LiPo buzzer is too loud, stick two pieces of bubble gum into the holes of the little speakers. This will muffle the sound and still make it loud enough for you to hear it. Enjoy printing and building! ...Have fun, don't forget to like!

If you still think you want to do it, I'd recommend my slot-lock attachment system as seen in TauZ and Tau brace.\r\n\r\n**Update** I redid the foot so it screws directly into motor frame which is far better and simpler to print\r\n\r\n**Update** I...

If you print with a different setting, ensure your slicer preserves them.AssemblyDrill out the hole in the upper control arm (19B) that attaches to the knuckle mount to 4 mm. Ensure an M4 screw fits snugly but without threading into the plastic.Test...

When printing these items, it's highly recommended that you use Cura's "Horizontal Expansion" feature with a negative value. A value of -.12 works well for me. If they're still fitting in too tightly, try -.15, then -.20, and so on. BuckleTiles are...

(20/05/2022) ATTENTION J'AI UPLOAD DES MAUVAIS FICHIERS… IL Y A DES NOUVEAUX FICHIERS POUR:Power_Bot_Black_x1Power_Bot_White_x1Power_Top_Black_x1Power_Top_White_x1Dimensions et InformationsElle fait environ 35 cm de haut pour 7 cm de large.Il y a 63...

... The design is 10cm diameter, I printed at 40% scale and lost some details, recommended do it bigger that 1:2 for fully details Star Wars: The Old Republic is a massively multiplayer online role-playing game (MMORPG) based in the Star Wars universe.

This was printed on a Flashforge Guider II, High Quality, so the tolerances are good, but I also allowed a 1/4mm tolerance between parts and at this level of quality, it gave me a good fit. Painting it was using acrylic spray, primed and filled,...

So you have to print everything but only one BLTouch mount... All screw connections are designed for melt inserts. I used Ruthex but others should fit as well if they have similar dimensions. In total you need : 10 x M3 inserts (8 if you...

When I built my dedicated printing room, I failed to notice that the switch for the overhead lights was located at the top of the rear wall, which is not very convenient. This design has 4 main parts: The Switch Plate mechanism, The Corner "Pulley",...

I was able to incorporate all the points that I had missed in the past.One of the biggest features is that the component can be printed according to current needs using the customizer within OpenSCAD.Previous solution:The whole thing is based on my...

The play translates into uneven surfaces which are readily apparent on large flat horizontal surfaces, but also affect every other print in some way. There are a few mods here and you can try all or one at a time. First off, the bearing holders on...

PLEASE CHECK YOUR PCB SIZE BEFORE PRINTING! I MEASURED MY PCB WITH A DIGITAL CALIPER AND IT MEASURED 65mm X 39mm EXACTLY Note there are many versions that look similar but have key differences. Make sure you use the one that is exactly as shown,...

Two are required, the shape is rotationally symmetrical so only one model is needed, and printed twice. The jig is 2RU (3-1/2") high which is the same as the smaller PDP-11/03 chassis height. To use, simply push the jig into the rack from the...

First, print the elements before covering them with foil. I used aluminum tape typically used for sealing air conditioning ductwork; you could also use a thin sheet of metal for the element. For either design, holes are included to enable multiple...

That being said, Creality did an exceptional job with the CR-10 that third-party manufacturers can duplicate it using the cheapest, lowest-quality materials available, and still manage to print beautifully with some elbow grease. I say my CTC A10S...

... with magnets so everything keeps in their site. With this tray design you have extra slots so you can organise tokens as you prefer and can be used with Arcadia Quest and Arcadia Quest Inferno I've used the color of each guild to print the trays :)

My vision was for a device that: - Utilizes a 6x6 printing bed - Employs hard tac-switches over rubbery elastomers - Has a vertical layout reminiscent of classic GameBoys - Is simple to assemble and modify - Runs on the Raspberry Pi 2, unlike older...

After print is complete the battery will not fit right away. You do want a snug fit. Most definatly do not want it to go flying out of the case while using it. Take a paint stir stick and super glue some sand paper to the stick and sand paper the...

updated keyboard support update 05-02-2021 ------------------------ -updated top case to avoid printing defects -improved clearance of top cover update 06-24-2021 ------------------------ -included gap in keyboard support for diskdrive ribbon...

If the magnets or bearings are tight in the holes, it could crack the printed part. Just reprint one or half a percent larger. NOTES: (1) Sometimes you might find that the hole is not centered in the blade, which means the blade could be heavy...

This set contains 5 heavily armoured Kingsguard Heavy Cavalry equipped with lances.  the Riders and Mounts are separate models for ease of printing and painting. Presupported files are included for each model in both STL format and LYS (Lychee...

Later I will add photos of a finished print with some painting and post-processing tips.See the Remixes section for two other variants.-------------------------------------------------Tento bunkr, tzv. <strong>řopík</strong> (podle ŘOP: Ředitelství...

I added a ziptie location for the cables (break off the designed-in support), modified a ton of tolerances, got the fan ducts adjusted to the proper height with the nozzle, made a permanent BLTouch mount, embossed "CR-10S Pro V2" and "Micro Swiss...

Print 16 squares, 8 of each color and 2 times each piece (one of each color). Rules of the game: https://www.teteamodeler.com/activite/jeu/jeu-echec-initiation.asp Playing the introductory game of chess Installation of the chessboard and its...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   Margo,...

Edit* (4/11/2019) I Have replaced the V2 Generic Race Cartridge and Sleeves with CORRECTLY oriented for easy drop&print, I have also included a Mirrored Version that will accurately hold the FR (and alternate language editions) per user suggestion. ...

Minimum color layer thickness is set to 0.6 units for all print jobs. Lug width is 5 units in overall diameter. Font style name is not specified at this time, resulting in the default font styling. Lug length is 4 units from base to tip. ... Note:...

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: Short term tool storage for tools being used on an active project Organization to help keep the bench cleaner To help facilitate rapid tool acquisition...