adimlab gantry 3d models

A brace for the adimlab gantry.

This bed handle is made to fit the Adimlab Gantry and Gantry Pro.

This is an updated STP file for the Adimlab Gantry, featuring my most recent modifications. Please incorporate these changes as necessary to ensure optimal performance. ...Enjoy!

Mount the E3D Hemera to the Adimlab Gantry using the necessary accessories. ...Choose any compatible cooler you like, or opt for a custom remixed model that's been specially designed for this application.

... ...It is specifically engineered to fit the Adimlab gantry printer, which incorporates UBL technology and a Volcano hot end. ...To minimize heat warping from the print bed, it's recommended to print this bracket using ABS or PETG materials.

These custom foot designs are tailored to fit seamlessly over standard 3D printer feet, ensuring a precise fit on various models, including the Adimlab Gantry-S printer. The unique design features two distinct parts: a sturdy top and a durable bottom...

I upgraded a few components and needed additional clearance on the top of the extruder mounted circuit board my ADIMLAB GANTRY 3D printer, which is actually a Creality CR-10S or HC Maker 7 clone. I also wanted to relocate the run-out sensor closer to...

I designed a new-style mainboard enclosure for the ADIMLab Gantry, specifically tailored to the "white board" Gantry model, but it may also work with the "black board" Gantry. Unfortunately, I don't have access to a "black board" Gantry to test its...

This is a remix of an Ender3 filament guide to fit the Adimlab GantryS, Just remove the white spacers under the filament runout sensor and install the guide plate. You will need a 4mm bolt,nut and washers as well as a 608 bearing. Print 2 of the...

This custom cover shields the ADIMLab Gantry extruder circuit, which is located above the extruder motor. When the original carriage housing is taken off, the extruder board is left vulnerable to damage. This protective cover will offer a degree of...

An additional mount for the Z motors on the Adimlab Gantry printer. ... Hardware: 2 M3 x 12 screws for the motor 2 M4 x 8 screws to mount on the 2020 extrusion 2 M4 t-nuts Install Put M3 screws in Put on motor and start M3 screws Push t-nuts...

BL Touch for the AdimLab Gantry with the extruder in the photo. It replaces one of the LED strip mounts at the bottom of the extruder. I have tested the model that works with the Volcano Hotend. The Shorter one (untested) can be used with the...

This mod is for Z stabilization braces on Adimlab Gantry systems. The required part is a 24 inch long rod with 1/2-13 UNC threads, along with two hex nuts. One of these hex nuts should be press-fitted into the knobs or you can print the knob with...

This is a two-piece cover for the ADIMLab Gantry extruder circuit that sits above the extruder motor. If you have removed the original carriage housing, the extruder board is left exposed and subject to damage. ...This cover will help to protect the...

This reconfigures the AdimLab Gantry printer to be a single unit instead of having a separate control box. This configuration turns the printer sideways allowing better clearance when backing the printer against a wall. (the bed goes side to side...

12/2: Additional Amazon links for parts have been added: https://www.amazon.com/gp/aw/d/B07MF15JQX/ref=ya_aw_od_pi?ie=UTF8&psc=1 https://www.amazon.com/gp/aw/d/B07H97FZMS/ref=ya_aw_od_pi?ie=UTF8&psc=1 01/18/2020: If you plan to install a linear rod,...

This reconfigures the AdimLab Gantry printer to be a single unit instead of having a separate control box. This configuration turns the printer sideways allowing better clearance when backing the printer against a wall. (the bed goes side to side...

BL Touch for the AdimLab Gantry with the extruder in the photo. It replaces one of the LED strip mounts at the bottom of the extruder. ...I have tested the model that works with the Volcano Hotend.</p> <p>The Shorter one (untested) can be used with the...

ADIMLAB GANTRY PRO Z-RAIL CONVERSION Warning: This modification uses MGN9 rails and not the usual MGN12.

since i could not find the STL for the alignment tool that came with my adimlab gantry pro, I made this in tinkercad

This is an advanced version of the Adimlab Gantry-S adjustable Z-stop, featuring gears that allow for precise adjustment. ...For detailed installation guidance, visit https://www.thingiverse.com/thing:4240240.

This is a new version of the Adimlab Gantry-S adjustable Z-Stop with gears for the adjustment. Please see https://www.thingiverse.com/thing:4240240 for installation instructions. ... Category: 3D Printer Parts

Remixed rear plates to allow the use of kevinakasam's ender 3 belt driven Z conversion with Adimlabs Gantry-s (and possibly Gantry pro) printers.As my printer is running a direct drive setup, I didn't include an extruder mount on either side, but if...

The ADIMLab Gantry (original) does not a have a parts cooler. There is a JST port on the daughter board for one, however. I already have a published design for a standard cooling fan. ... This is a turbine style fan that I think works better and...

A complete setup for the E3D Hemera on the ADIMLab Gantry to operate linear rail on the X-Axis is straightforward. Simply attach the rail to the 2020 extrusion using stock bolts, which also hold the mount and block securely in place. Four M3-6mm...

For assistance with this process or any other questions related to the ADIMLab Gantry-S printer, join our active community on Facebook at https://www.facebook.com/groups/1235236596606278. Update: I've added a version of the bed level sensor...

A parts cooler for the ADIMLab Gantry was conceived as an improved solution for printing. A friend sought a better way to cool prints, prompting me to design this custom part. It accommodates a standard 4010 Axial fan, integrates seamlessly with...

Companion STL for Upgrade Guide on ADIMlab Gantry to SKR 1.3. The New LCD Isn't a Match for the Original in Size, So This Mount Serves a Convenient Purpose for the Screen. Big thanks go out to Electroskippy for designing the mount and Daede for...

Tinkercad link: https://www.tinkercad.com/things/4TySCePNNE5 Print Settings Printer: Adimlab Gantry Rafts: No Supports: Yes Resolution: 0.24 Infill: 10 Filament: MG Chemicals PETG Black Notes: For the slotted version, use supports everywhere (not...

Tinkercad link: https://www.tinkercad.com/things/4TySCePNNE5 Print Settings Printer: Adimlab Gantry Rafts: No Supports: Yes Resolution: 0.24 Infill: 10 Filament: MG Chemicals PETG Black Notes: For the slotted version, use supports everywhere (not...