an enclosure 3d models
509018 3d models found related to an enclosure.thingiverse
This is a tyrapclamp to secure an enclosure to a steel pipe or alu tube. Print 2 of these parts, slide a tyrap through both slots and glue (24u epoxy) this to the back of your enclosure. The fixed tyraps will keep the enclosure in place. ...
thingiverse
This is an enclosure for an Arduino project with a LCD front panel. The front panel contains an LCD screen and a push button. The back panel contains a On-Off switch and a DC power jack. The front and back panels are removable, and it makes a...
thingiverse
Owl Lamp [4] Thing URL : http://www.thingiverse.com/thing:344419 [4] Thing Author : hidecat [4] Thing Licence : Creative Commons - Attribution - Share Alike [5] Thing Title : Dosatori - Set di cucchiai dosatori per ipovedenti [5] Thing URL :...
thingiverse
Frame to keep the supplied reel-holder in place within an encolosure. It does not interfere with either the bed, or the enclosure. It attaches the reel-holder to the left foot of the printer. It can be built in PLA on blue tape. ...How I Designed...
thingiverse
A holder for spare build plates, holds 4 ikea mirror tiles
thingiverse
Customized version of http://www.thingiverse.com/thing:47956 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options:...
thingiverse
Print and assemble instruction: https://www.thinker-talk.com/post/fully-3d-printable-spool-holder-with-four-3d-printed-planetary-gear-bearings Fully 3D printable Spool Holder with four 3D printed Gear Bearings optimized for an enclosure. I made this...
thingiverse
I wanted one that is fully 3d printed, but with bearings and also optimized for an enclosure (filament goes directly down). I didn't find one, so I designed this one myself. Visit my blog for more cool stuff: https://www.thinker-talk.com/ For...
thingiverse
An enclosure for using an Arduino Nano as an IR-transmitter controlled over USB. Check out my project on GitHub for the software and build instructions: https://github.com/robertmoro/MagicLightingRemote. The top has optional holes that fit two...
thingiverse
Intel has released a Arduino like board called Galileo. Unfortunately it is too big for any Arduino case. So this is my solution. It isn't really tested. But the model is mostly good. ... If you find that you need to make tweaks to it, I have included...
thingiverse
I don't have an Ikea Lack enclosure, but I liked this design, and my enclosure has a 1/8 inch (3mm) whiteboard roof-top, so I remixed this design to fit. I also made the filament exit just as smooth as the entrance, and it is still able to be...
grabcad
The gear set fits in the enclosure box the output torque is 21.1 NM & 8 rpm.
prusaprinters
This is a redesign of the Einsy board box to mount the board outside of the enclosure. The four screws for the board should be long enough to go through the board and to the inside of the enclosure to attach the box to the side wall. Positioning of...
thingiverse
A breeding enclosure for ants that l designed. It has a small compartment for a gravity feed watering system and a removable door to enter / exit of the ants and for future upgrades. The watering module requires a 5ml syringe, that you can pick...
thingiverse
Small connectors to hold Acrylic sheets (2 mm) as a quick and simple enclosure for 3D printer...
thingiverse
Created so that I can bolt my electronic components (Ender 3 v2 Motherboard, Raspberry Pi 4B, Dual Relay Board, Buck Converter and PSU for Pi) to a plastic plate, and can then stick these to the base of my electronics box (with double sided tape to...
grabcad
This is my Design, I finished my design one week ago but because I was sick and can not add to challenge 2019, this is one reduction gear with 600:1 rate,
thingiverse
This model is designed to be something additional that they could print to allow them to mount the enclosure further away from other parts. The idea is that this is screwed into the enclosure of your choice from one side and then screwed into the...
thingiverse
This is an enclosure for an electric skateboard. It's designed for a 10s3p battery with bms. In one piece, you can place 2x 3 pieces of 18650 cells in parallel, so you have 6 cells in one piece. To mount the enclosure i used screws and...
thingiverse
This is an Air Cleaner / Scrubber for an enclosure I am building. The enclosure is based on an Ikea TINGBY so this is made to work with the table top from that product. I know that hardly anyone uses the TINGBY and the LACK tables are more popular...
prusaprinters
This is an Air Cleaner / Scrubber for an enclosure I am building. The enclosure is based on an Ikea TINGBY so this is made to work with the table top from that product. I know that hardly anyone uses the TINGBY and the LACK tables are more popular...
thingiverse
I designed a Death Star Echo Dot/speaker enclosure. The enclosure fits two 2-inch speakers. I used a cheapo Amazon Basics computer speaker kit because it is cheap ($11-14 depending on the day) and it comes with all the cords and circuitry. ...This is a...
thingiverse
This thingy belongs to [this Instructable](https://www.instructables.com/Cozy-Bedroom-Lighting-2-Star-LED-Curtain/) and is the enclusure for an LED curtain
thingiverse
There is an E-Stop and the start/hold/reset buttons are there. I also moved all the connections to the front and put the control switches on the top. I also put in a viewing port so I can perform troubleshooting on the arduino or relay visually. ...
prusaprinters
There is an E-Stop and the start/hold/reset buttons are there. I also moved all the connections to the front and put the control switches on the top. I also put in a viewing port so I can perform troubleshooting on the arduino or relay visually.</p>...
thingiverse
ESP32-CAM enclosure with an articulated hanger for a car Use cyanoacrylate or similar to glue the parts I use https://jameszah.github.io/ESP32-CAM-VideoCam/ to loop record to the SD
thingiverse
A simple to build wood and Perspex 3D printer enclosure built onto an IKEA "Alex" drawer unit. Full build details and other 3D Printer Project on my web site here (still a work in progress)...
thingiverse
It was designed for my enclosure which is based on an Ikea TINGBY coffee tables. I'm pretty sure there are few if any folks out there using the same, so this is a very niche design right now. If you can provide exact dimensions for say a Lack...
thingiverse
This is a approx 5mm "tunnel" and another that is 5.15mm for the "Filament Passthrough for an Ikea (TINGBY) based enclosure" at the link below. This is only the tunnel, so the rest of the parts will be needed from the link: ...