android figure 3d models

Buildings 1) Human Living Space -This is the repurposed spaceship used to fly to Mars -It is already radiation-proof out of necessity from the trip to Mars -Already equipped with heaters from space travel -Much of fuselage is repurposed into a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be ommitted on the inside. These are for sink and drain plumbing only,...

I have completed assembly and everything works so this addresses some of my main wants for this awesome model. I am also going to include the full parts kit here (the originals I used also), so everything you need is in this one thing saving any...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

The model isn't geometrically perfect as I did the scaling in blender (The only editor I know how to use), but it works which to me is the most important thing. You will need a couple screws to put it together as the ones which come with the...

(Rotate these angles accordingly if you rotate the model.) This way, you will have two layers of crossing extrusions in the spine folds. This makes for much stronger, long-lasting book hinges.</p><p>For<strong> print-on-print</strong> technique (used...

My Fusion 360 CAD model has 0.09mm of axial clearance so the printed threads should effortlessly spin together. Extruding over 0.09mm will make it extremely difficult to twist the nut and bolt together using fingers, so just reprint both parts with...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be omitted on the inside. These connectors are specifically designed...

Because of the simple geometry of the Box and the Pieces, these modest settings produce a very nice model in a relatively short print time. Please Note: Although I have not provided the solution here, I will respond to personal Thingiverse messages...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

Creality slicer use edit, multiply selected models. PrusaSlicer use cut and past. I'm sure it's possible in other slicing software too. I would recommend printing a few extra as you may damage the edge on a few when inserting them. Assembly: ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

idk what slicer or print settings were used on the original print, but I had to redo the entire geometry of that area to get it to print right without disturbing the bevel of the rest of that model. Unfortunately, given I don't have the original...

All necessary supports are pre-applied to the models (there is no need to add additional supports). The main body of the stein/mug prints with cylindrical supports, the left/right lid have perforated supports, the lid top doesn't require supports...

unless you have a special edition like a Porsche, Mercedes, or older Audi, VW, or BMW model, which is what I have. For most of these special editions, the original push bar won't fit. I found a design on Thingiverse called *Klein-laui* and tested...

Trim/Cut plastic flowers from a dollar store. Modified from this model: https://www.thingiverse.com/thing:3666273 Photo frame with a sliding/rotating cover. Slightly recessed oval of 40mm wide by 55mm tall to attach a 2D printed image/photo. Three to...

Issues that I have with the design: In hand, the phone with my case (Model brand Apple silicone clone) on it fits snug. I can shake it vigorously upside-down and the phone doesn't fall out. However, After strapping it to the stem, the mount develops...

This model is for a “streetlight-style” wired garden/pathway light. Brighten up your garden path with lights, without spending a fortune on MoonRays or similar products where a single lamp can cost up to $20! In bulk I can make these for about $3-5 a...

I can only describe what I did or share my experiences and provide respective models and a SketchUp project concept file (the .skp file) so that you can adapt or improve it for your Stargate. In one of the comments from '5ft Lighted Stargate'...

Yes, there's an actual tank model underneath all the nonsense; it's just badly covered over since I built a spacefuture tank around it. I used a different source for my sponson lascannon; the sponson mount is from Seb's Sicaran proxy, so any of its...

This model is cheaper than the usb c version and charges the Oculus Quest perfectly. This greatly improves your playing time and you could even charge the battery while using it. One design came close to what I liked, but was made for a different...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_overlap = 0 custom_back_extra_port_corner_radius = 5 printer_tolerance = 0.4 stencil_pattern_element_radius = 6...

Make the adjustments, render the desired  STLs and print it! The models are in the position, they should be printed. No support is needed. ...I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Print the model as is for the Front piece and MIRROR the part Z axis for the Back part. Position the part on its back with the legs sticking up, then rotate to 45 degrees to make it fit on your bed. Print the Front (part)... Then print the Back...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

It Lets You See Your Model Being Built and Doesn't Obscure View. Why Make Yet Another Cooler? Cooling Plastic Just After Its Been Extruded Is Essential on FDM Printers and There Is a Lot of Choice for Cooling on the Makerbot Clones. I Tried All of...