anemometer 3d model

https://www.printables.com/de/model/172064-phaetus-taichi-mount-and-fanduct-w-dual-5015-fans- ________________________________________________________________________ This is an highly integrated Mount and FanDuct for the upcoming Phaetus TaiChi...

(You may be able to get away with shorter bolts but these were the only ones I had that would fit) I have included a thumb screw model to make it easier to open and close the cover without a wrench. You will need an M3 heat insert but I cannot stress...

Since my first published keybboard was The1987 (https://www.printables.com/model/299777-the1987-a-modular-retro-inspired-87-key-mechanical) and it's fairly popular, and its designed around the Phantom circuit board and Teensy 2.0, which are no longer...

The hole for the cable tip should be wide enough for any similar cables, but if not you can pretty easily remix the model by just cutting the hole to be larger or adding material where needed. I suggest printing the dock upside down and including...

Trim/Cut plastic flowers from a dollar store. Modified from this model: https://www.thingiverse.com/thing:3666273 Photo frame with a sliding/rotating cover. Slightly recessed oval of 40mm wide by 55mm tall to attach a 2D printed image/photo. Three to...

... If this is the case, and accuracy is important, you should scale up the dimensions a little bit to compensate. I only tested this for small gaskets. If the model proves unpractical for larger gaskets, contact me and I'll see how I can improve it.

Except for the Sunlu mount plate just lay the models flat. The Sunlu mount plate I printed standing upright - even without support (although some minor bridging is needed, but that was no problem)</p><p>As mentioned above, the hygrometers are...

Once I print and test it, I will update this with the final model and the STL's.\r\n\r\nI'm currently working on a new version with a removable tray for the Pi since I now plan to use a Pi4 with this project.\r\n\r\nI would not recommend printing...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

*Note: don't order a GearVR with a white body - it is a 2015 model with smaller lenses that don't fit.* **UPDATES** **V3.3** (slight comfort improvements over v3.2). [print 1 for each eye] **Added a version for the prescription inserts from VR Lens...

Anyways, this is getting out of hand so here's the important stuff: Many models to choose from! 18mm sensor 12mm sensor 8mm sensor Then choose you cap: 2 stock fans with chain mount 2 stock fans no chain mount No fans no chain mount No...

Helicopter Collective Controller Work in progress. 6/17/20 Added File Added collective_open v4.f3d (An assembled model of all the parts.) You can alternatively use my Russian style grip located here:...

... Norrick      Details: Gravemaw is standing around 145mm tall on a 60mm customized base. The model is multiple parts, the file contains: 1 x Body 4 x Arms 2 x ½ tongue parts 1 x Intestine 1x Customized 60mm base. ... Support Version Included

I will be answering questions there and I look forward to seeing pictures of people's in-progress builds: https://www.thingiverse.com/groups/curta Update 6/27/2017: The main axle and step drum model have been updated. The old one works, but the hole...

As far as assembly is concerned, it's all pretty self-explanatory when you see the models, but here are a few tricks: Use as little wire as possible, but make sure you use good wire. The wires run from the grip and back, across the side of the...

I could not find caps / hoders which suited my project, starting from inspiration of certain models existing in AA, I made a design under fusion 360 which corresponds in the size of integration, as well as the possibility of making spot welding. ...

Select model on plate -> right click on it -> Add support enforcer -> Load..) Assembly Mounting the whole thing onto the printer is a bit fiddly. Here's how I went at it: <ol> <li>Remove the case from the hotend carriage and remove the old radial...

I've seen some Hedron models before, but none of them were quite right to me - they got the patterns wrong or just looked off in some way. So I set out to design my own, and this is the final result. Well, these are the final results because there...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 45...

The previous file had a gap of 1 mm in the height of the wall between the two cutouts at the front of the model. The replacement file fixes this. Updated "Ability Card Divider" file, to include a cut-out, to make lifting deck from the tray easier. I...

This model fits seat shafts with a 16-groove, skip-tooth-top, 12mm nominal shaft:&nbsp;(note skipped groove, blue arrow)&nbsp;Probably best to print these with the spud pointed up for minimizing how much trouble the overhangs inside the hole will...

* The Ridgid adapter / switch part that you previously had to purchase separately is no longer needed, it is modeled in. You use more of the same brass strip used for the Ryobi part to create the Ridgid battery contacts. * The clips for the Ryobi...

If you do this, use the "Pusher Extd" model. To modify the solenoid: 1. Remove plunger. Remove about 3mm of the black base and sand flush with the metal slug. Sand the black base to make it slightly thinner if you want to add an additional spring...

The "Advanced_Fit" version is meant for printers with tighter tolerances and may provided better heat break cooling due to the extended cooling channel.** After looking at all the options for a hotend mount here on Thingiverse and Facebook i decided...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

Issues that I have with the design: In hand, the phone with my case (Model brand Apple silicone clone) on it fits snug. I can shake it vigorously upside-down and the phone doesn't fall out. However, After strapping it to the stem, the mount develops...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

My daughter loves playing chess, but the magnificent pieces by NTX9 often fall out the original box when she tries to relocate.Therefor I made a remix that allows for a lid to slide in front of the pieces. The lid is of course based on the pieces...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...