anet a8 nozzle 3d models

The built-in supports are designed for a .4mm nozzle and for the size that the model is presented. Use your discretion for which parts to use if you resize the model significantly. **Note: The built-in supports have only been tested with the...

I was originally printing the perimeters at 40mm/s, and 20mm/s didn't seem to help much, but 10mm/s (and possibly slightly cooler nozzle temp) fixed it. I printed at 10mm/s perimeters, 50% external perimeter, and 20mm/s infill. I will update the...

The Paper Mates have about 3.7mm of range where they come into contact with the paper until the nozzle touches the print bed. If you set your tool height to 2mm when plotting and lift up 5mm (7mm from print bed) for movements this should apply...

My bowden-cable printer nozzle likes to make webs. \n \n After cleaning (if necessary), the USB cable can be installed. The shorter of the two male cables will be cut and used to feed power to the brushless fan. The...

They printed on a Creality CR10 with 0.6 nozzle and 0.3 layer height. Print instructionsTo begin with, the kid should get his magical kit ready. The 3D printed kit is composed of a wand, 3 magical tricks and some tokens for the kids to make...

The built-in supports are designed for a .4mm nozzle and for the size that the model is presented. Use your discretion for which parts to use if you resize the model significantly. 2 - The tail can be printed in two parts with a pin for...

The drawer should now slide into place.• I guess you're all done unless you want to make more drawers :)Installing Drawers under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will...

The part cooling fan outlet is close to the same level as the bottom of the nozzle. Just check your installation to make sure it doesn't go any lower. UPDATE 02/11/2019 Made the following changes to improve the Fan Shroud Only. All other parts are...

These can be made with a single nozzle printer using the multi-pass printing technique; Devin Montes has created an excellent tutorial on how to do this. The 'hole' parts have the same pattern as the 'mech' parts but with panels cut all the way...

You should only insert the NFC chip in the end because otherwise the hot nozzle could possibly damage your NFC chip and make it unusable.You can also use the color switch to stop the printer at a specific layer or height and don't switch the filament...

 If they are too tight, you can use a 3mm drill bit to clean them up.Wiring connector used: this provides quick disconnect for when/if you want to change the LEDs or do other...

Past experience & prints (with my Ender 3 using a 0.4mm nozzle) show that depending upon the font type, text which is at least 4.5mm tall & embossed 1.6mm high is highly legible. However, given that this text is a bit shorter at only 4mm tall and...

Hole sizes vary from slicer to slicer and nozzle diameter so you may or may not need to heat press in a magnet to get them to fit. None of these models should need any support, I try to avoid them if at all possible, but you will need to be able...

I encountered a few filament tangles, clogged nozzles, and badly leveled beds, but enough of me babbling let’s jump right into this project to see how I got it done right! At this point, I was learning as I was progressing through this project. I...

Because from the back you have the best view at the print nozzle when blTouch, the part cooler, the hot end cover and possibly a short led strip all stand in the way for an unobstructed view from the left, right and front of the printer. Thingiverse...

Secure cotton stuffing to the plastic base, thick enough to scatter any single light sources from the LED strip, but not too thick to block most light and add too big of a cone spread close to nozzle ends. </li> <li>Wrap the rod with cotton stuffing...

The lamp will automatically turn off 12 minutes after the time that the alarm was originally set for. Print Settings Printer Brand: RepRap Printer: Makerfarm 12Rafts: No Supports: NoResolution: Printed at .25mm height with a .4mm nozzle Infill: ...

Both the base and the drillclamp are made of PLA using a 0.6mm nozzle. print settings are: 4 top+bottom later, 3 shells, 15% Grid infill.The spring is made of TPU 98A. print settings are: t.b.c 5. AssemblyAfter printing add some graphite powder to...

So the nozzle will be lifted fewer times. Also you coul add a Logo to be placed in the middle. </li> </ol> <ol> <li>Card Design<br/> Use Paint.Net or inkscape<br/> Standard credit / business card size: 55 x 85 mm<br/> Make sure to only work in Black...

It's just to prime the nozzle. The included files will make 100 samples. You have to study these samples very carefully. You have to find the sample with the highest possible value that doesn't curve. We're talking about a curve that only moves 0.01...

Feel free to remix/use. Print instructions use PETG Filament we used a 0.3 mm nozzle on 0.25 – 0.3 mm layer height no support 30% infill 3 layers outer contour (for smoother movement - less infill) We added the bottom clip of the original prusa...

I did try printing with holes down the joints to save filament but found that the nozzles were knocking them off the bed due to warping. The flat bottoms make them more printable than my early round bottom versions, which needed support on the...

The built-in supports and braces are designed for a .4mm nozzle and for the size that the model is presented. Use your discretion for which parts to use if you resize the model significantly. 2 - There are some pieces that may need brims or rafts,...

Since I wasn't entirely happy with my first design (which works to guide my filament, but isn't exactly up to par) I designed a second version.\nI have printed this "thing" (black ABS w/ raft, no support, 130-degrees on the HBP (my HBP doesn't heat...

Move the Carriage into the middle of the X before loading filament to the nozzle. That way the tension from the Bowden tube is always the same. This could also be helped with other materials that don't flex as much as PETG.<br/> 3 TPU and Flexible...

It's a bit difficult to tell from the pictures but it looks just about perfect.The blue piece is a retraction test model for a 0.4 mm nozzle which was used at the moment.The orange is Prusament Polycarbonate (Blend), also a flow calibration cube.I'll...

Angled feet not only help with printing without supports, but also make the parts look like they are floating above the table, and each other, when viewed from a typical high viewing angle.&nbsp;Print InstructionsPrinting the models on their side as...

Creality CR-10 V2 with .4mm nozzle, glass build plate, BL Touch bed leveler.  CURA slicer settings The settings shown in the pictures are what I used to print my models shown in the pictures. You may have varying results but these...

All three parts were held together by 4x self cutting screws of type 2mm x 8mm length - F - Z.Before mounting them together I had to install the DCDC converter first (see below in Electric stuff section) and the RPi camera...

The lock opens or closes by itself. Print PLA or PETG.Nozzle 0.4mm, layer 0.12 to 0.2mm. CONCLUSION💚💚💚If you enjoyed the project please like it.💚💚💚Post your makes and let me know how it works out for you. If anyone has any comments about them -...