anet a8 plus dual extruder 3d models

I have fixed this by moving the entire box inboard 3mm. I also added slots for square nuts at the cover fasteners. Update 07-09-2019: Added version for Raspberry Pi 4 (untested by me but should work) Update 07-04-2019: Increased clearance to x-axis...

The guide fits around the rocket with two sets of rail buttons that engage in the launch rail (rails are usually 1010 extruded aluminium). On launch, the guide provides stability as the rocket travels up the rail - as soon as the rocket clears the...

To mount the shaft, the end should be tapered slightly (sand the very end down to about 6mm) to fit inside it to help secure and support it. How I Designed This The design was created by manipulating some scanned lineart in Mattercontrol using the...

We offset it 0.15 cm to form the line which created the longer side of the mouth.The ghost’s eyes were too wide with a diameter of 0.7cm, so we changed them to 0.6cm. Its mouth was also too wide, meaning it had to change from 0.35cm to...

I would then select the backside of the part, pointing inwards towards Pooky's head and use extrude to give it more room to fit into the main mesh. I'd then use the scale tool to align the vertices of the back of the part to become a flat surface.I'd...

slow it down if you have extruder issues)Special note for Prusa Slicer: Under Print Settings > Advanced, there is a "Slice gap closing radius" setting. You need to set this to 0. This is very important.DrainageGood pot drainage is important for most...

Next week we're printing the fourth side, and we're going to make it multi-colored, you don't need to have the Palette or MMU, and I'll give you my tutorial and you can use it to print other awesome colored objects too! 22.03.2021 - how to print...

Using a reference photo I have extruded points to match the text and ornaments on the top surface. Due to the inner and outer part this was quite complicated to design. ...I have used lots of booleans in Blender.</p></div> <p class="detail-image"><img...

However, I have now included another lid, This time the Text and Pentangle are Extruded so you can add another colour filament, Maybe a glowing one! See image Galaxy Silver and Black.If you didn’t want to use the box as a ‘Jack-in-the-box’ then the...

If that doesn't slide nicely, you may have to adjust your extrude speed to something lower. Your printer has to be fairly dialed in for all the mechanisms to work properly. ...See the video for more details.</p> <h3> Print Settings</h3>...

If the 12 is aligned Mount the adapter plate (cuts an M3 thread into the small holes at the bottom) and the extruder unit. Screw the bracket to the 7-way rail. Push both units on top of each other and check for fit. Aligns the 7s fine. The whole...

I found, though, that I needed the air to go more horizontally to directly below the nozzle as the extruded filament wasn't always cooled quickly enough (I use a volcano set). So I made a version (version 2) duct with openings that are more...

Updates: V1 Initial Upload V1.1 Added Offset Option to Allow for Printing Tolerances Changed Top and Bottom Plane Definition for Right and Left Twist to Be More Consistent Through New Configurations Consolidated Root Extrude Feature into Tooth...

Keep a look out for this.Designed for the Ender3v2 but more than likely fits other variants, however an OEM Creality controller board may not work unless it has a spare driver port.BOM2 printed parts in PLA.Bondtech Pancake stepper with spur gear...

The only problem I have had, is when doing a Z calibration and the extruder moves to the top of the frame, the filament will push up into the container and can slip over the edge of a full filament spool. This can be prevented by holding the filament...

I find slight variations in line quality acceptable; extruded plastic is more forgiving than a pen or marker when it comes to print surface/levelness. You might need an M3x6 screw, depending on your writing tool of choice. The photo of the bed...

* Extruded holes in the standoffs for the Raspi to the bottom (where they were too shallow). Update: June 13, 2019 Cases reported to fit nicely on Ender 3 Pro. Unconfirmed whether the lids fit as well. New Version: June 12, 2019 Received pictures...

If your hot end is longer, you may need to use a spacer to raise the extruder and hot end up off the mounting shelf to get enough clearance to use this Z probe. Video of the servo probe in action: Instructions The servo fits through the hole in...

There are spindles in various sizes to allow spools with large holes to rotate smoothly. Joiners for Multiple spool holders There is a joiner to link two spools in series for winding filament from one onto the other. Also a joiner to link spools...

Printer Brand:Prusa Printer:i3 MK3 Rafts:No Supports:Yes Resolution:0.2 Infill:10%  Notes:I always print these parts with 8-10% infill, how much i used for this print i'm not aware anymore.The inlay was definitely an 8% infill print.the numerous...

If you have good extruder cooling you can get away without them. I'd definitely recommend going for a higher infill if you plan on actually swinging this in anger. 15% does leave it feeling pretty hefty and solid, though.</p> <h3> How I Designed...

My mouse will print in a variety of settings, so do as you please in terms of how fine the extruder prints. 2.5. Export from Cura to an SD card that will go into the printer or directly to the printer with a cable. 3. Once printed, separate from...

Update 12/09/2018: I fixed size tolerance on all ports for easier installation and better fit, made it taller to relieve stress on the USB-C cable, added USB-C support to the bottom of the lid to relieve stress on the port without screws, and...

I printed on an Ender 3 v2 with cheap filament from Micro Center so it doesn't require high end stuff, but it does require a fairly well calibrated printer to ensure everything is the right size so make sure your steps/mm are calibrated for X, Y, Z,...

Good instructions can be found here.  Updates---  If you have any questions or improvements/suggestions do not hesitate to contact me!If you like what you see, consider following me to support my work - more to come -AUGU5TO | PrusaPrinters  Every...

Because the enclosure is so small and dimension a bit tight, check your printer’s extrusion rate so as to not over extrude. I printed everything in PLA with a 0.4mm nozzle and a layer height of 0.1mm. I will suggest that, at a minimum, the 5 buttons...

Filament: Matter Hackers ABS Pro Extruder temp: 230 C (lens caps and brackets were printed at 215-220 C due to being small parts...the excessive heat @ 230 C caused melting/stringing) Bed Temp: 90 C (the max for my printer) Speed: 15 mm/s Infill:...

If you want to do a single-color print, you can just print the main body of the part and end up with a recessed graphic.Customizing the graphic:It turns out that you can import and extrude SVG or DXF files in openSCAD!Download filesNote: Prusa...

I recommend a few inches from the left edge in line of your extruder if using the factory Bowden setup. The guide tube should stick out about a half inch past the bottom side of the top table when all the way through. Glue it down if you want, though...

The coupler is only acting as a guide, it is not essential to have it as well fitted as when between an extruder and hotend as there are no pressure issues involved, filament will just be pulled through so don't risk breaking the print trying for the...