anet a8 stepper motor 3d models

The way the fan is installed on my ANET A8 is a complete disaster. In case of clogging, I'll have to disassemble the entire thing and risk losing my precious Z-offset calibration... As many of you, I don't think the heatsink is necessary. To work...

... panel parts to take less time to print, + I added a little hole to the left front panel to install a reset button. More info on this later, but basically a reset button switch like you can find on the centre(center) of the default Anet A8 board.

Dear designers and makers, On this occasion, we have created a box to house the main board that comes standard in our Anet A8 and two mosfets (one that will regulate the power of the hot bed and another that regulates the power of our extruder). The...

The way the fan is installed on the ANET A8 is a real mess. In case of clogging, you"ll have to disassemble the whole thing and loose your precious Z-offset calibration... As many of you, I don't think the heatsink is needed. To work properly a heat...

This print mount was designed specifically to hold the QuadFusion print head on the Anet A8 Plus 3D printer. Two versions of this mount are currently available, with a third version set to be released soon. The details for the mount can be found...

I engineered this component to diminish the z to y stability of an Anet A8. The stock configuration solely relies on all-thread and eight nuts to connect the bed to the acrylic frame. Then, the front plate only has a half hole to clamp with nuts and...

... for the one that appears in the background as someone had asked about it. It's built entirely of hardware store parts. I don't think any of the rods were specially cut, either. Print Settings Printer: Anet A8 Rafts: No Supports: No Infill: 60

This was created to replace the 9-blade "muffin" fan on my Anet A8 extruder. The stock fan is weak, and unfortunately, if you have the same problem I did and break a blade, the fan becomes VERY noisy and vibrates excessively (affecting print...

... piece. The spool holder arms slot into the brackets. The spool bolt and nut...that should be obvious. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 mm Infill: 25% 3D hexagonal (Slic3r) Category: 3D Printer Accessories

This is a remix for the quick change X carriage for Anet A8/AM8. The carriage itself is my remix of another carriage that has a part fan and sensor mount.This should fix "standard" plates from the source, however, I had problems with it either...

... a stepper motor. ...Its meant to be attached to this model:https://www.printables.com/model/69291-mechanical-wall-clock/And if you have problems with the electronics, I've followed : https://maker.pro/arduino/tutorial/how-to-control-a-stepper-motor

I am creating a CAD model of a stepper motor that I am currently using. The model is based on specifications provided by the reseller, and it should accurately represent an Astrosys Stepper manufactured by Minebea-Matsushita Co., LTD. This 3D model...

... where space is limited, such as robotics, CNC machining, or automation systems. With its reliable performance and low power consumption, the 28BYJ-48 stepper motor is an excellent choice for projects requiring high accuracy and smooth operation.

The Stepper Motor Stand is a versatile and compact solution designed to house the popular NEMA 15 Stepper Motor. This stand offers an easy-to-use interface and robust construction, making it perfect for a wide range of applications. The open frame...

adapter for mounting a power supply model S-360-12 on an Anet A8Filament : Esun PLA+ blackSupport : YesInfill : 15%Walls : 3

Another essential nozzle fan guard designed specifically for the popular Prusa and Anet 3D printer models, ensuring safe operation and optimal performance.

A straightforward enclosure to shield the cooling fan from view. ...Since Anet-branded prints are not an option, I designed this decorative casing myself.

... detent torque of 6.8 Newton-centimeters ensures smooth and consistent performance. The Nema 23 Hybrid Stepper Motor is equipped with four lead wires for easy connection to your system, and its shaft diameter measures a substantial 6.35 millimeters.

Mount is designed for a Stepper Motor that is 31mm tall and 41mm wide.You will need: two 12-14mm countersink boltstwo 12-14mm M3 boltsPossibly some washers2 V-slot nuts to thread onto the countersink boltsThis mount was created to secure a second z...

You'll need four hands to properly reattach the fan / heat sink / extruder stepper motor. I've tried it with just one screw removed, but it was essentially the same frustrating experience. I've since searched for alternative solutions from others...

... one. Thanks. Leo Update 2017.07.06 Added a version for use with a BLTouch "Anet_Fan_Sensor_Holder_BLT_Leo_N" You will need two M3 screws. ... Update 2017.08.13 Updated "Anet_Fan_Sensor_Holder_BLT_Leo_N" to accommodate the new version BLTouch-Smart

... The brackets print easily without any support needed, allowing them to snap securely over the NEMA 17 stepper motor with no additional attachments required. ...To keep everything organized, I used zip ties to secure the wires firmly in place.

To combat overheating Ultimaker stepper motors, print three cooling shrouds that slide easily onto the X, Y, or extruder steppers without removing them (assuming wires are in place). Fasten small #4 bolts through each shroud's five holes and mount...

This is a basic model of the popular stepper motor. My motor's name is Q4-4402, but it is actually a very common component that was torn out from an old inkjet printer. The diameter of this motor is 42mm, and its height measures only 15mm. If you...

Stepper Motor NEMA 17 Dummy The Stepper Motor NEMA 17 is designed to meet a variety of applications requiring precise movement and positioning control. Its compact size and high torque output make it ideal for use in CNC machines, robotic arms, and...

The mounting system utilizes the existing motor bracket, so just replace the regular motor with this stepper motor assembly and you have cnc control of the spindle. You will need to 3D print the stepper motor mounting plate, and 2 pieces of the...

Support for NEMA 17 Motor with Bowden Extruder

This motor mount is specifically designed for the Anet A6. Please feel free to use and modify it as needed. I've worked hard on creating this custom design, and I hope you find it useful. ...If you do decide to build it, I'd love to see your progress...

A fresh batch of thumb wheel locks for the A8 arrives. ...My setup relies on precision-crafted M3x5.5x5 brass heat-set inserts, carefully selected for their reliability and durability.

I built a straightforward extruder mount for my A8. ...I found the positioning on all other mounts to be off-putting, so I designed this one with functionality in mind and it's been working flawlessly.