antelope 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

This is a model of a convenient sliding lid box with an easy to use locking mechanism consisting of a bump on the lid that keeps it securely closed. Note that for slim boxes the lid does not bend as much and the locking and unlocking may be a bit...

I changed the position of the threaded inserts and added additional to replace the hex nuts. Modified the cable paths and tie wrap holes for easier printing, and thickened up some sections to print better. Modified how the front and rear clamp...

Really like the wheel from TheSloppyApprentice's Watermill and was looking for ways to hold it besides that large frame in the source.So I could make it stand in a bassin or hang under some opening where water is dropping off.So here are 2...

now you can the stands/feet print without support or if you want the texture of the powder-coated pei sheet you can print it on its side without support.Release Candidate 1.5 - 15 January 2021Updated some sections to the model so it's stronger when...

The following customizer options were chosen for this particular model. The best approach for any specific sign will ultimately depend on your unique needs, such as text requirements and the required appearance and functionality. line_spacing =...

The engraving starts at 1.8mm and the model continues at 2.2mm. Use contrasting colors for a clear reading. <b>note:</b> <i>* If you suffer from corner bulge / swell or an elephant’s foot after printing, carefully sand / deburr them. When...

and Pause Layer = 2. How I Designed This Print on Window Screen This model was designed to have the printer paused at ~1mm to have the screen inserted. I made sure I made the frame thick enough to allow for multiple layers to be printed on each side...

Since my first published keybboard was The1987 (https://www.printables.com/model/299777-the1987-a-modular-retro-inspired-87-key-mechanical) and it's fairly popular, and its designed around the Phantom circuit board and Teensy 2.0, which are no longer...

Different sizes and materials will result in orbs with different focal distances, which may mean you have to adjust the model for yours. Print it strong-- thick walls are a must. You'd be surprised how heavy the orb is. Also, I had to "floss" the...

Those are only used to ensure consistency and are not necessary for rendering the model. I also pulled in the 40mm Fan Grill from the Sanginololo case and copied it here to make it easier to find. Those little 40mm fan grills print really nice and...

--------------------------------------------------------------------------------- Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support...

As of 09/16/2018, I've not yet modeled or printed the capstan bearings, nor have I fully solved how I will drive the capstan. My current thought is to use a drill attached to the underside of the platform, using a belt to drive the capstan. I would...

I have left the original design files as well to preserve version control.&nbsp;Design File Included: .f3d, .ipt, step, .skp, and .obj files.&nbsp;Follow The Makers Workbench...

Update 01.04.2023 A friend i have made through the Neo Community have discovered that the clearance might not the good with the standart Neo, because the belt housing on the left stick out further, he have provided the file named...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

... and presupported version. This product contains the following parts: 80mm Base Body Legs Cleaver Arm DnD 5E Datasheet Get a 40% discount on this model by joining my Patreon! You can also order physical copies at my shop on Only-games! ...  

Once I print and test it, I will update this with the final model and the STL's.\r\n\r\nI'm currently working on a new version with a removable tray for the Pi since I now plan to use a Pi4 with this project.\r\n\r\nI would not recommend printing...

The COMPLETE The Bloodhunt bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Bloodhunt Knights were the first Soulless Vampire troops to be sent to the mortal lands of...

About the Models Update: 24th September 2017 Added Y-splitter D6 8th September 2017 Added Multi Material for BLTouch 12 August 2017 Added Multi Material series 11th April 2017 Added Bowden series MM Parts and Y-Splitter I added the new MM parts just...

And get your supports in order first, the models need a relatively precise and flat supported surfaces. <font size="3">The modification uses many parts from the original setup, but the PTFE tube must be cut, making this a non-reversable mod...

The extruders are mounted using the same procedure.Made with Onshape:Source CAD: Snapmaker Artisan Modular Side ShelvingPrint Recommendations:Print in PETG for the increased strength.Rotate the models so they are laying down, bosses facing up.Print...

UPDATE: 07/16/2019 Project 399 - Front Crossfire Mount - Depressed 3525.stl - I've been running this model the most. I thickened the sides so it provides more lateral stability, improved the chamfer at the sides to make it smoother, and I thickened...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 0 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

... Norrick      Details: Gravemaw is standing around 145mm tall on a 60mm customized base. The model is multiple parts, the file contains: 1 x Body 4 x Arms 2 x ½ tongue parts 1 x Intestine 1x Customized 60mm base. ... Support Version Included

  I've been using the one in the picture for a few weeks and apart from not looking as pretty with the cam open, there's absolutely no difference in performance.I think I have allowed enough room to print this model with a .6mm nozzle but if you are...

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A wise monk who was captured, tortured and blinded after speaking out against the cruelties of Irinax’s followers in Iriksha. His blindness is now a blessing, for he does not bear...

... with any light color and use a permanent black marker for the text. These models are not designed for dual-color printing. You'll need to print two Monster Ability Card holder v1. ...One is for the Monster cards, the other is for the shop cards.</p>

Version Update: 1.2 (5/2023) ======================= Updates: V 1.0: First version released (Jan 13th 2023) V 1.1: Added G1/4, added typenames to models (Jan 30th 2023) V 1.2: Added G1/3, added all kuves 30_x (May 3rd 2023) All (and the lateset) STLs...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...