anycubic chiron firmware 3d models

I'm sure it could be done with custom firmware, but what I did was connect the printer to my PC using Repetier, and then using the manual controls figure out what the exact coordinates of the buildplate home were (and how wide I want it). I use...

I used a Teensy 2.0 and QMK for firmware. Because I installed the switches and soldered all of them before re-designing the plates, I needed to improvise to get the rigidity I wanted (hence the weird screws in the picture below).</p> <p><strong>Here...

I have since replaced both with standard Creality 42-40 and all is good and running really cool.The firmware changes were relatively simple, there are only a few comments to tweak. I did however have to invert the direction of the X & Y motors. I...

This is somewhat bespoke, in that filing, trimming and etc are all needed Removing the WIP mark now - as only the instructions may change if folks need clarifications Added a hand wiring diagram and firmware example including the source zip if you'd...

Programming the microcontrollerThe software used is the cloud-free and very versatile firmware Tasmota by Theo Arends. An already compiled version e.g. tasmota-DE.bin can be used. Reflashing is possible with the software Tasmotizer via USB micro...

The "solution" is then to Dremel out a few pieces of metal to expose the SD/USB of an SKR/MSK board. I don't like irreversible changes so I will not alter my case. But I do want to access the SD card for firmware changes. The USB I don't need because...

The electrical part of the build will probably be another $100.For the firmware settings with DRV8825 driver set either of these depending on whether you are using Y or Z for rotary axis$101 = 64 ;DRV8825 &amp; 1.8-degree Nema 17 1/32 step$101 = 128...

If this results an error, then you printer has no eeprom or it is not enabled by the firmware. This however is no show stopper. Create a line containing the gathered calibration information like "M92 X100.3 Y101.2" and add this line to your slicers...

If this results an error, then you printer has no eeprom or it is not enabled by the firmware. This however is no show stopper. Create a line containing the gathered calibration information like "M92 X100.3 Y101.2" and add this line to your slicers...

Plastic goes on the top side of the PCB, solder goes on the bottomInstall your MCU either directly onto pin headers (not recommended) or socket your MCU as per these instructionsFlash a test firmware onto your MCUOnce you have the PCB prepped and a...

Firmware: brand new based on GRBL 1,1h, implements LCD 2004 and SD card wich lets you work directly from SD or manually move axes. BOM Electronics: manual version - n. 1 washing machine BLDC motor - n. 1 button self-locking...

As long as you have good adhesion, things should turn out nicely. Be sure to look at your slicer and pause at the appropriate place to insert your pennies - I can't teach you specifically how to do this as different firmware handles things...

Due to the flexing of the shaft there are definitely some quirks with this extruder but nothing some good slicer settings or firmware offsets should be able to remedy. The majority of artefacts seen in tests to date relate more to Retraction and...

The firmware changes were relatively simple, there are only a few comments to tweak. I did however have to invert the direction of the X & Y motors. Uncommenting Z_CLEARANCE_BETWEEN_PROBES & Z_HOMING_HEIGHT stopped the Z axis from trying to drop to...

If you don't do this, the servo arm will move in the opposite direction you expect when you calibrate it (this may be fixed in a future firmware modification, but for simplicity's sake flipping the connector does work) Assembly steps for winder Fix...

Print Area: 220x220x210 (X/Y/Z in mm) Printer Size: 360x380x440 (X/Y/Z in mm) Features: Using a RAMPS 1.4 board running on Klipper Firmware Raspberry PI with Octoprint LED Stripes with custom plugin for Octoprint for heating and printing status...

All you need is a flat surface to put everything on.For controlling the machine I have use the widely known and very well done GRBL firmware, running on an Arduino Nano. I recommend the really excellent project page from Arnab Kumar Das, who has done...

You will have to cannibalize your P802M for parts, visit the hardware or parts bin, drill/rig things for endstops, and likely re-flash the firmware. I replaced Melzi with RAMPS 1.4 because I don't like repetier. Do not tear your P802M apart until you...

Update your maximum Z height to 209 mm and reflash the firmware. All done! Updates 2018-09-28 New files are up. You can build it now. Half-way is pretty easy. Going all the way is not. 2018-09-29 Improved the BOM and wrote instructions. Note...

The HallON website (Garage Maker Zone aka GMZ) only provides pre-compiled firmware, for some boards only available in Polish. Some information can be found on the GMZ forums, but again, only in Polish (thanks Google Translate!). Since my set-up...

Fit the fan and connect either to the MOSFET if being used as a firmware controlled Control board cooler or to a 12Volt source that is live when the control board is powered on. Ensure fan is fitted to exhaust air from the box to outside. Make all...

Due to the flexing of the shaft there are definitely some quirks with this extruder but nothing some good slicer settings or firmware offsets should be able to remedy. The majority of artefacts seen in tests to date relate more to Retraction and...

The firmware changes were relatively simple, there are only a few comments to tweak. I did however have to invert the direction of the X & Y motors. Uncommenting Z_CLEARANCE_BETWEEN_PROBES & Z_HOMING_HEIGHT stopped the Z axis from trying to drop to...

You will need to perform a PID tuning on your hotend after installation, and possibly specify a different thermistor type in your config file or firmware, depending on the new thermistor you use. Alternatively, you can reuse the old heater and...

(Open source firmware for ESP devices: https://tasmota.github.io/docs/) (Einrichten von ESP8266 / TASMOTA und diverse interessante Details zu D1-Mini:...

To control the boat engines, alternatively it is possible to: Try to hack a old drone board using MPU-6050/6000 to disable the gyroscope and accelelerometer(what i'm using now!) and use the drone transmitter or if the board protocol is compatible a...

Since switching on the BLTouch code in the Marlin Firmware compile did cause the code size to exceed the memory size of the 8 bit board that I had just installed for the quiet drivers, I changed again to a 32 bit board which works perfectly well now...

I created this project to get more experience in modelling for 3D printing using Fusion 360, practice my soldering skills, and get a chance to do a little ESP8266/Arduino programming. *Features* hang it from the wall using the built in hole(s) or...

Note: I don't recommand getting batteries from China, for some reason the delivery delay is much longer than for other components.Some scratch tape to mount the battery: here for instance4x M2x20mm screws + 4x M2 nutsMandatory equipment:RC: Jumper...

If you don't do this, the servo arm will move in the opposite direction you expect when you calibrate it (this may be fixed in a future firmware modification, but for simplicity's sake flipping the connector does work) **Assembly steps for winder**...