anycubic chiron z axis stabilizer 3d models

Because of where my Anycubic Chiron is located, I need some feet that raise it 30mm from the surface it's on (it's on-top of my half-height server rack, and with where my windows are, the spool hits the window shelf). The surface it's on is metal,...

... incorporate the use of bearings to make everything that much smoother...but this was a quick fix for now and seems to work well enough for the time being. all in all a very simple but plausible print design for those of us with an Anycubic Chiron

This spacer for z-angle stabilizer (tested on Sovol SV01) allows to mount the spacers without touching the motors for z-spindles.

In just five minutes, this installation enhances the X-axis stability of your Printrbot LC+ without requiring any drilling, disassembly, or recalibration. With a single piece needed, it simplifies the process for you. To print the required part using...

I designed a clip based on Mosaic support data since no Chiron clip was available yet. ...A larger version is compatible with the Palette 2's included velcro, while a smaller one attaches directly to the Chiron's filament sensor.

Extrusión semi-directa para Anycubic Chiron usando el hotend mk8 /mk10 se utiliza el mismo carro original, pero HAY QUE CORTAR EL VÉRTICE DONDE SE ATORNILLA LA CADENA QUE LLEVA EL MAZO DE CABLES, de forma que la parte superior del carro quede...

IN THAT WAY IT IS AVOIDED COMPLETELY ANY FLEXION OF THE WHOLE SYSTEM. Currently, using nozzle 0.6 I have retractions between 1.6 and 1.8 mm at 50 mm / s Print instructionsUnassociated tags: extruder chiron, mk8 chiron, mod chiron Category: 3D Printer...

This is the siplest and most effective TITAN AERO VOLCANO conversion for the ANYCUBIC CHIRON. One design is without possibility to mount the filament sensor directly on the extruder and the other is with it. You can use the original screws and...

Semi-direct extrusion for Anycubic Chiron using the hotend mk8 / mk10. The same original X carriage is used, but the vice must be cut where the chain which carries the cable harness is screwed, so that the top of the carriage remains completely...

Simple Upgrade Method for Original Chiron Spool Holder - 100mm Spool - 2.1 kg Capacity. ...Requires Only Two 608 Bearings (8x22x7mm) in Total.

I discovered solutions for fixing the bed or tightening belts, yet none were found to prevent x-axis wobbling due to an inability to tighten one bearing. This compact tightener resolves this issue. Additional components are required: 1. A screw...

This mount replaces the existing Chiron Filament Sensor, and allows you to use the trianglelabs.org filament sensor in line with the stock extruder. I needed this filament sensor because I primarily use Octoprint, and it doesn't recognize the...

Getestet habe ich das nicht. Die Düse bleibt in X und Y exakt an gleicher Position. In Z geht sie 7mm nach oben, weshalb die Z-Endstops auch nach unten verschoben werden müssen. Auf den Bildern ist zusehen, dass ich eine andere Kabelkette verwendet...

In Z geht sie 7mm nach oben, weshalb die Z-Endstops auch nach unten verschoben werden müssen. Auf den Bildern ist zusehen, dass ich eine andere Kabelkette verwendet habe. Die originale Kabelkette von Anycubic kann auch verwendet werden. Auch der...

In Z geht sie 7mm nach oben, weshalb die Z-Endstops auch nach unten verschoben werden müssen. Auf den Bildern ist zusehen, dass ich eine andere Kabelkette verwendet habe. Die originale Kabelkette von Anycubic kann auch verwendet werden. Auch der...

With the original mount to top, I didn't have enough cable to get full travel on Z axis. - Added 2 holes for a zip tie to keep cables in place, and add clearance for the cables. - Mount on top stepper motor screws instead of bottom, as is it protect...

To address this, I reengineered BLKFLD's stabilizer to sit slightly higher on the lead screws, incorporated a built-in filament guide and wiring hook, and optimized the clearance to achieve a full 200 mm of Z-height after modifying the original...

Now screw the Z-Axis slowly by hand down, without bending the bed, but supporting the Z-Axis and ergo the Printhead. At last thigthen the D-Wheels nuts and thighten the screws from LEFT (!) to the right. Now it should be better after an...

This modification targets the z-axis top holder for the Prusa i3 Original, drawing inspiration from its original mount, which utilizes 8mm smooth rod and 5mm thread. The design is crafted to fit snugly with the smooth rod yet remain loose enough with...

I came across a design on YouTube (https://www.youtube.com/channel/UCkXj9_80x1PquHxWZtT-6Hg check the videos about the Chiron - I'm not sure which one specifically it was...) a couple of months ago and decided to create my own feet for the Chiron...

This is a conversion kit to slap a SKR 2 into your AnyCubic Chiron (SKR 1.4 also probably works because they have the same mounting holes and similar layout).The Holes that need to be drilled into the side of the chassis (if you aren't just planning...

This is a conversion kit to slap a SKR 2 into your AnyCubic Chiron (SKR 1.4 also probably works because they have the same mounting holes and similar layout). The Holes that need to be drilled into the side of the chassis (if you aren't just...

This is a customized version of https://www.thingiverse.com/thing:3195516's "Chiron hotend housing and wire guide" by jangermann, modified to be compatible with the E3D V6 hotend.\r\n\r\nRevisions include:\r\nThe circuit board was relocated to the...

With the original mount attached to the top, I found that there wasn't enough cable to achieve full travel on the Z axis. I added two holes for a zip tie to keep cables organized and provided clearance for them. Additionally, I mounted the stepper...

My Take on the LED Strip Holder for the Chiron - A Customized Solution. Attach 70cm LED Strips, consisting of two 35cm sections, using cable ties for a secure fit. ...Then, power them directly from the PSU with a Step-Down Converter.

I used this mount to fit a hemera onto my Chiron. ...&nbsp;Remixed from Tmaxx21 on thingiverse at: https://www.thingiverse.com/thing:4297095</p><p>&nbsp;I removed the part of the mount that holds the original I/0 board since I don't need...

**Update: I've Enhanced the Duct for Improved Air Flow Focusing Towards the Nozzle** **Update 2: Eliminated Interference Between the Duct and Heat Block, Boosting Performance** I Designed This Upgrade to Optimize the Fan Duct on the Chiron, Resulting...

I only plan to use this design for small prints because the rod needs to be significantly extended to accommodate the 450mm build height of the Chiron. However, that's a project for another day. Update 30/05/2019: I discovered that trying to fix...

//----------------------------------------------------------------------------------------------------------// Z axis leadscrew anti wobble for the i3 mega. It's a two piece design inspired by other designs found on thingiverse. The top piece clips...

I recreated the original Z axis endstop handle from mjedlinski to make it compatible with my I3 Mega which has a V6 Clone hotend and an Ultrabase - actually, it was the pre-Ultrabase version, but I upgraded/added it. The height adjustment fits...