anycubic i3 mega s stepper driver upgrade 3d models

Anycubic i3 Mega S Y-Carriage Belt Tensioner UPDATE: Added a Carriage_mk2 file which features a slightly sturdier back. I noticed after a year of use and perhaps slight over-tensioning on my part, the screw that pulls the carriage back has started...

...... I designed this **X-axis belt tensioner** to fit onto an **Anycubic i3 Mega S** because there isn't one that I could find readily available on here. You can install this onto a stock Ai3MS with **no modifications necessary** to the current fixture.

I designed this X-axis belt tensioner to fit onto an Anycubic i3 Mega S because there isn't one that I could find readily available on here. You can install this onto a stock Ai3MS with no modifications necessary to the current fixture. No need to...

I started with the peg system to use the original knobs but found it much easier just to put pegs on the knobs themselves. The "Back Right" versions are because I have a bed cable guide installed (modified because the gap was too thing for my Mega S,...

Anycubic i3 Mega /i3 Mega S - Small V6 Hotend and Filament Cooler To reduce the noise, ineffectiveness, and size of the i3 Mega or i3-Mega S hotend cooler, a simple solution is presented. The benefits of this cooling variant are as follows: - A...

Anycubic i3 Mega / i3 Mega S - Z-Axis Improvement ______________________________________________________________________ The Z-axis of the Anycubic i3 Mega is prone to vibrations, and here's a small solution. The following advantages result: - 4...

Hi all, I've remixed the original cable shroud and added the Mega S logo to the hotend cover's front face. I also added the blank version without the letter "S" for other Mega series users can customize it. You can use a double sided tape to...

Inspired by stories how amazing direct drives could be I decided to remake my i3 Mega-S ('S' is very important here, latelly you will understand why) I went across lots of amazing projects and even printed one based on Philipp's guide...

I modified the original design to enable using the thicker titan that comes with the mega setup. You'll need to cut off the useless circle that covers the gear on the lid, or maybe just use or print another lid if possible. I used a hacksaw - you...

Yet another take on part cooling fan improvement for the i3 Mega S. This design uses the existing fan and carriage and allows for cooling from both sides. I performed a bit of CFD to help ensure airflow doesn't hit the nozzle, as much as possible. I...

I SUPPORT THE DUAL FAN FOR ANYCUBIC I3 MEGA DRIVERS. I USE TWO 50MM ULTRASILENT FANS. A "Y" CABLE IS REQUIRED TO CONNECT THEM. CAUTION! When closing the printer, I noticed that the support exceeded 2 mm in height. ...To address this issue, I created a...

I'm still waiting for my I3 Mega to arrive, so please point out any issues with the design. For customizing this thing using OpenSCAD, follow these steps: 1.Download the OpenSCAD script (fanduct.scad) and save it in a folder on your computer. -...

This results in a significantly hotter Y stepper motor on my i3_mega, equipped with TMC2208 drivers, which led to periodic layer shifts solely on the Y axis. Furthermore, the duct fan becomes increasingly noisy over time. To address these issues, I...

Snaps around the frame of a Mega-S. This might not fit depending on how you have your filament sensor set up. I don't use mine, so it's not an issue. Would be easy to adjust in TinkerCAD which is all I used. I've found that the long side is a little...

...The print results are improved!The Duct and the hotend cooling are CFD flow optimized.You can use the original fans and screws - no need to buy new parts.https://www.prusaprinters.org/de/prints/47884-anycubic-i3-mega-hotend-fan-box-also-mega-s-mega-x

The "Back Right" versions are because I have a bed cable guide installed (modified because the gap was too thin for my Mega S, original is in the "remixed from" list and modified version is in files), and the normal versions didn't fit. They might...

This is a heat-gun base/holder that can be clipped onto the top of the Mega (S) frame. It's intended to be paired with some kind of shroud (like a sturdy heat-resistant bag, or chamber) to create a heated environment. A heated environment will make...

It spins very freely and smoothly; FAR better than a regular vertical spool holder (like the stock mega S holder). The bearings I bought from aliexpress are not the best, so they have very slight inner-race play, but it doesnt affect the spin at...

... dafür einen Kabelschlauch, 2x Kabelbinder und etwas Schrumpfschlauch. Viel Spaß beim Nachdrucken. My version of the cable routing on the heatbed of the Anycubic. You need a cable sleeve, 2x cable ties and some shrink tubing. ...Have fun reprinting.

I know - this conversion requires some craftsmanship - and the parts I made only fit if you use the 5015 fan in conjunction with the original case, but maybe it's a suggestion for others to avoid the airflow downwards. The parts should not be...

As I didnt want to disassemble the extruder, I created my own mount that can be used with the stock L bracket that comes with the titan extruder (on Mega S). I believe it is a steel bracket and its is extremely strong so there should be no problems...

... part. Same mounting holes as with the original cover. Doesn't require any supports brim or anything and is optimized for quick and easy printing (no steep overhangs, etc) Designed to be printed with Anycubics default .4 line width / nozzle size.

In addition the original knobs are also hidden pretty well under the hotbed.From all the knobs I found already designed by fellow Mega owners I liked the version of MKingCharles the best and printed one sample. After using it for a while it felt a...

From all the knobs I found already designed by fellow Mega owners I liked the version of MKingCharles the best and printed one sample. After using it for a while it felt a bit to large for my taste and why clip something over the original knob and...

This creation was crafted using Tinkercad's powerful tools. ...Edit and refine it effortlessly at https://www.tinkercad.com/things/3sGUm2buKYY.

The primary distinction lies in the hook's placement on the backside of this alternative gauge. To accommodate this new gauge, I had to make some minor adjustments to dede67's gauge holder design. ... For the required mount arms, please refer to the...

I made another remix of dtylerb's great clips (https://www.thingiverse.com/thing:4196202) so I have a place to hang my safety glasses. ... Please note that the clip is designed to be mounted on the left side of the printer (since the right Z mount is...

I Remixed https://www.thingiverse.com/thing:3440488 to fit the cheaper Dynavox Damper.I havn't tested the Oehlbach version but those are working fine for me.Printed with 50 mm/s and .3 layer hight.Link to the damper I used:...

Printed with 50 mm/s and .3 layer hight. ... Link to the damper I used: https://www.amazon.de/gp/product/B076CJH6ZH?ie=UTF8&psc=1&linkCode=sl1&tag=dgerold-21&linkId=aea5304e807b7b7913f2d52a511e72d0&language=de_DE&ref_=as_li_ss_tl (Affiliate link,...

Haruka Ze's Direct Extruder Installation: Cable Retainer Production To secure the cable to the main body, I created this part: https://www.thingiverse.com/thing:3954252 I replaced the original bolt with a 35mm M3 panhead screw because it was too...