anycubic i3 mega s stepper driver upgrade 3d models

This is another take on the squash ball vibration dampeners for the Anycubic i3 Mega. Squash balls have been used as dampeners since their inception, and they excel at this task. The machine runs almost silently and strikes a perfect balance between...

This sleek card holder is designed specifically for Anycubic I3 Mega S 3D printers. ...It requires no removal of the support screw for easy mounting.

This set of parts is for the Anycubic I3 Mega with Ultrabase. Included are: A hotend enclosure to replace the existing metal housing. A hotend base cover that fits securely over the new enclosure. And a parts cooler that pairs perfectly with a 5015...

This project started because I needed to increase reliability and maintainability of the Anycubic i3 Mega and Mega-S printers I use to make productions parts. The hardware frame of the printer is excellent, but the 8-bit control board and v5 hotend...

... on for this print to work correctly. You may need longer screws (M3x10 screws) for this project. On my Anycubic I3 Mega, M3x6 screws were not sufficient, but you can try using them first and then decide if you need to upgrade to M3x10 screws.

I recommend checking out my "Scolopendra" fan extrusion system - it's truly top-notch. To see how this modification is installed, take a look at the video below, where I walk you through the entire process step by step. Important Note: If you...

Tool holder for the Anycubic i3 mega. ...No screws have to be loosened for fastening. Werkzeughalter für den Anycubic i3 mega. ...Zur Befestigung müssen keine Schrauben gelöst werden.

Tool holder etc. ...for original tool of the Anycubic I3 Mega/S. ...The magnets are 18/8mm and pressed into place in my case only.

Werkzeughalter u.a. ...für original Werkzeug des Anycubic I3 Mega/s. ...Die Magneten sind 18/5 mm und in meinem Falle nur eingepresst.

This is my design for a webcam clip for my Anycubic i3 Mega-S. ...I wanted to do timelapse and keep focus on the model.

This versatile card holder is designed specifically for Anycubic's I3 Mega S 3D printer. ...The unique feature of this card holder is that it can be mounted without removing a single screw, making installation quick and hassle-free.

This is a sleek Extruderhead upgrade for the popular Anycubic i3 Mega 3D printer. ...Enhanced cooling performance makes it stand out, and its visually appealing design earns high marks.

For buying the cheapest and upgraded AnyCubic i3/ Mega S, check out this link: https://www.facebook.com/pg/gohappygo.ghg/shop/?ref=page_internal Or simply type "Gohappygo Shopping" in Facebook's search bar. ... For Anycubic i3 Mega/Mega S Upgrade Set +...

A compact MOSFET holder specifically designed for the AnyCubic I3 Mega 3D printer.

My First Attempt at Designing a Hotend Fan Box for the AnyCubic I3 Mega.

Привет! ... Предлагаю мой вариант скобы для стола принтера Anycubic I3 Mega. ... Крепится при помощи кабельной стяжки.

Anycubic i3 mega cable mount Never break a cable again! ... With or without cable tie .

This is an experimental subject for demonstrating filigree print patterns on AnyCubic I3 Mega 3D printers.

Anycubic i3 Mega Schrittmotor Kühler für 40mm Lüfter. ...Maße des Schrittmotor 40.2mm +-0.1

... settings, are stored in Thing files. For detailed information on the component's design and assembly, visit these resources: https://www.thingiverse.com/thing:4169539 - parts guide https://www.thingiverse.com/thing:4144046 - display mount manual

<p>Hello,<br/> I designed this little tool to fix the extruder in the "open" position so i can just roll the filament up to the spool without having to stop the clamp.</p> <p>Hope you find it as useful as me :)</p> Category: 3D Printing

Thanks to @ringo2k for the base model. ... I added side panels to prevent the Filament Spool falling off the Holder ;) You need 1 8mm rod or M8 rod and two normal 608Z ball bearings.

I decided to remove the noisy bearings with something better and quieter. ...The grip is in place of the original holes, the tanks are fastened with 1 bolt on the base, at your request it can be drilled and fastened with 4 bolts The necessary bolts for...

I opted to swap out the rowdy bearings for a sleeker and quieter alternative. The grip now occupies the spot where the original holes used to be, while the tanks are secured with a single bolt at the base, as per your request - it can also be drilled...

Hello, I created this handy device to adjust the extruder to the "open" position, allowing me to effortlessly wind the filament onto the spool without having to halt the clamp.

The AnyCubic I3 Mega Gallow is handy for suspending multiple items, such as a USB cooling ventilator for rapid cooling with a clip.

Drag chain holder for Anycubic i3 Mega Pro. The i3 Mega Pro has a different extruder than the i3 Mega. I created a suitable holder for it. ... The other part is here https://www.thingiverse.com/thing:2860786

Anycubic Mega-S SmallFeet Small feet using existing screw holes when removing the bottom panel of Anycubic Mega-S After installation, it is good to put a non-slip sheet

I'm thrilled to share my debut design in Fusion 360, a project born out of necessity - I needed to level up my Anycubic i3 Mega's print bed, and that's when the adjustable legs came into play.

Parts required: - PC4 M6 pushfit connector (one that feeds the reverse bowden tube all the way through) - At least 60cm bowden tube My Anycubic i3 Mega designs can be found in this collection:...