anycubic mega s octoprint 3d models

I've included a picture showing what the FoV looks like from the cam via OctoPrint. This print requires 2 M2x10mm screws and 2 M2 nuts for assembly. Once the mount is assembled, the clip part slips snugly over the y-axis frame, straddling the left...

Please take a look at my Upgrade, Settings (Cura) Guide for the Anycubic: [Guide](https://www.thingiverse.com/thing:3409767) --------------------------------------------------------- This is a Filament Spool holder designed specifically for the...

I attach my Raspi to the Anycubic Mega S with Octoprint installed, securing it firmly in place using two M3 screws and nuts that I have on hand.

I love my Anycubic printer but I wasn't crazy about how the cable bundle was zip tied so tightly to the print head bracket. The zip tie was causing a pretty sharp bend in the cable and also forced a sharp bend at the connector. This could lead to...

I redesigned this awesome fan duct, because it didn't fit my fan, beacuse of it's thickness of 10.6mm! ... Props to "Conceptual3D" for the source remix and "H_Run" for the original STL!

This is a holder for the Adjustable Foils from Philipps 3D's Shop:\r\nhttps://philipps-3d.myshopify.com/collections/downloads-stls/products/einstellfolie-0-05mm-x-50mm-ohne-griff\r\n\r\nThey work perfectly for...

# Remixed from - https://www.thingiverse.com/thing:3954252 - https://www.thingiverse.com/thing:3537449 - https://www.thingiverse.com/thing:4035830 # BOM (Bill of materials) - 12V Hotend (Stock) https://s.click.aliexpress.com/e/_Afq2Ub - 12V 4010 Fan...

I really love AlexWYYC's tensioner design, so I decided to try to integrate it in Titan Aero DD carriage's belt holder. ***You'll need:*** + <u>Two M4 bolts</u> (at least 30mm long) - as in original belt holder + <u>Three M4 nuts</u> - plus...

All you need is: - 3x ball-bearing (12x28x8 mm) (ID x OD x W) i used S 6001 RS - Drill or cut a smal notch in your original filament holder - 2x nut and bolt M3x16 No supports needed. ... You can adjust the width to your filament role and the tension...

- Reinforced the thin side and bottom walls by thickening to 2mm - Removed the floor around the heat block - I believe this is intended to shield the nozzle from additional airflow, but there's not really enough clearance for this to be practical and...

Hotbed leveling improvement: * Cost: 1/5 * Difficulty: 1/5 * Goal: Catch the hotbed when it's hot without using adjustement screw * Mean: Add a simple printed part to handle the hotbed 6. Axis guide lubrication: * Cost: 1/5 * Difficulty: 1/5 *...

Please note that the printer's conventional wiring requires only two 12V inputs from the PSU. I required two additional inputs to power some external Mosfets - hence a four gang socket. However I have designed a three gang version, as well as an...

This is for a 40mm x 10mm NF-A4x10FLX Noctua fan specifically. ...For mounting purposes, utilize the longer screws provided with the original fan.

The engineer secures the Z end-stop screws firmly to prevent them from shifting erratically.

If double Drylin bearings have been installed on your X carriage, the exposed ends will protrude from their mounts. ...These covers will conceal them.

Upgrade for extruder

Use R8-2RS (1-1/8 OD, 1/2 ID, 5/16 thick) bearings. Drill a 1/2" hold through the OEM spool mount and use a fully threaded 1/2-13 HHCS and capture it with a nut. I use a wing nut to tighten the spool on the holder. PIctured is a 4" bolt, but it...

As I tend to forget which direction makes the bed go up or down, I remixed the knob. ... With this remix the direction is crystal clear.

You'll find everything you require right here in this tool holder.

hallo Liebe Druckerbande... Leider hat das was ich von Alex100dre gedruckt habe bei meinem neuen Any nicht gepasst. ... Kaufdatum 12/21, daher habe ich ein Remix erstellt das super passt!

When installing Drylin bearings in the Y carriage, they tend to bind after tightening the set screws for the rods. These bearings fix that problem by letting the rods float freely in the mounts while keeping them firmly in place. Remove the set...

This holder uses original arm but with less friction. I use a nail to fix the rollers to the main body. ...The nais is a little bigger than hole so I just heated it to fit.

Update: 02.01.2022 Ring 3mm tiefer gesetzt - weniger Airflow am Heatblock Ringdüse verkleinert um mehr Strömungsgeschwindigkeit zu erzeugen, Verstärkungen angebracht um Verwindungen zu vermeiden. ... Ring size reduced, more rigid

I remixed the equipment box from BrezZZz because I wanted to have smaller inlays for nozzles, cutter and tiny printed parts. So my remix has the same dimension than the orginal with some holes to save material and different divisions on the...

remixed using Rick and Morty Stencils.

A few simple holders for a 10mm wide LED strip. The holders are simply clipped onto the inner frame of the printer. The two angle holders need to be mirrored once each in the slicer. ... You can find a suitable one-meter LED light on Amazon:...

A handle so that the hotbed can be easily moved.

No special settings. ... Printed with PLA.

I couldn't find any spool holders I liked so decided to design my own. I really wanted something sleek and modern without having to "clip" around the frame and didn't want it to be bulky.The roller assembly is a remix from...

This is a simple accessory designed to cover the bottom of the coldend cover on X carriage. Its purpose is clear: to prevent air used for cooling from also cooling the print. This can lead to warping or delamination with ABS and other materials,...