anycubic predator upgrades 3d models

You can find this here: https://www.thingiverse.com/thing:3883602 (NEW UPDATE 9/2019 - Metal Shafts on Gear Carrier with Bushings) I built a Rover 2.0 and incorporated the changes made by escexed in his "Planetary Gearbox Upgrade for FPV-Rover V2.0"...

The astute observer will notice that the keyboard has been upgraded. The model is slightly cartoonish, but it turned out decent and the ports are all pretty much where you'd expect them if you've seen a Color Computer. Card slot on the right side,...

... videos. Since the levelling seemed consistent, I decided to upgrade to the dual extruder printhead and this works well too. ...I have another thing for mounting the autolevelling sensor to the back of the dual extruder heatsink here on Thingiverse.

Note that you'll need to upgrade the Select Mini's power supply to use the heater; I plan to create a basic guide for this soon. SOME NOTES: - No special tools (except a 3D printer) are required for this project. I used a hacksaw, scissors, a drill...

Further InformationHead over to our Website for help on Printing and Painting some of the Awesome MeepleForge Upgrades CUSTOMS INFO - Please note that we are based in the UK, therefore please check customs duty limits and fees your Country imposes...

Also replaced my HEPA filter after 4 months so added a photo of the discoloration compared to a new filter. UPDATE 08/02/19: .STEP file added for v7 UPDATE 06/18/19: This is v7 and is a significant upgrade in terms of print time and air flow...

&nbsp;Also I installed a dual drive geared extruder because the extruder that comes with it is awful and needs an upgrade.The last weak link was the firmware. &nbsp;I had originally hoped to try the <a...

Further InformationHead over to our Website for help on Printing and Painting some of the Awesome MeepleForge Upgrades Printing and Painting help - meepleforge.com/painting-guidesStay Informed - meepleforge.com/subscribe SocialsFacebook :...

EZ-TRIM Harness line Gen 2 is a revolutionary system to trim your harness lines while sailing : watch the video : https://youtu.be/t7izQPLgtv0 This is an upgrade of EZ-TRIM Harness line Gen 1 (Thing : 4520587), much thinner and lighter. And also...

I even created some lore around the blaster for siths and giggles: ==================================================================== The DC15-X line of weapons were part of the project to replace the existing weapons of the Republic military...

UPDATE 19/04/2020 Forgot to mention that I use a nozzle to probe offset of #define NOZZLE_TO_PROBE_OFFSET {-49,-12, 0 } Also if you are looking for how to get your firmware and slicer upgraded to work with this then check out my other thing here. Do...

Once you are level 60, you can convert it to MK XII by right clicking it and selecting "Upgrade". Dynamic items can improve in power to a higher maximum than leveless items can. In Star Trek: Discovery, the Red Angel Suit was a powerful device...

#New Linear Motion for Prusa i4 The next printer upgrade started. This time I put MGN rails. For this, I used an aluminum substrate, but also the model is available for 3D printing. I also decided to change the belt tensioner. I also added a handle...

If you have a problem with the transaction, please write to https://www.facebook.com/RCTruckRallymodels UPGRADE 14.10.2020 We added 3 files for the back of the truck. The rear cover for easy folding can be completely printed out and screwed together....

You can of course use pheneeny's fantastic full-frame replacement which will ultimately be more stable and stiff than mine due to the use of 2040 extrusions, however, I'm of the opinion that 80% of the A8's main mechanical issues, such as a...

I have spent the last 2 weeks upgrading my printer and tweaking the firmware and slicer settings to get the best possible finish using silk copper filament. The stuff is so shinny, any defects in quality are very visible. I hope to me printing...

During printing, I didn't use my active fan, and I printed these on a CTC printer with upgraded extruders that enabled better filament feeding when working with ABS. The door file can accommodate a metal rod for hinges or hinge files can be merged...

Consolidated two PSU boxes for MPCNC and added upgrades for spindle control. Goal is to - Allow both manual and G-code spindle control, Measure RPM directly with hall sensor on spindle and calculate load, Possibly adjust Spindle voltage to target...

--- Upgrade your kitchen's style with a touch of classic sophistication. Check out my suggestion for the Umbra Paper Towel Holder Challenge on https://grabcad.com/challenges/umbra-paper-towel-holder-challenge. This timeless design can be 3D printed...

Because it is so easy to take apart and remove everything, it would be relatively simple for users to upgrade to a new version, or make other models. So far, my ideas for future growth include:</p><p>• USB powered fan</p><p>• Additional cable...

Inspired by the adjustable Z-bed by brianvanh I wanted to have one which can be adjusted motorized controlled by the upgraded smoothieboard in the cutter.The realized bed can move its surface up to 30mm below the lasers focus.Beside the printed parts...

However, the original little buck converter seemed to be getting quite hot considering the lowish power being consumed so I thought I'd upgrade the 5 volt supply for the LED's. This case has a pair of countersunk mounting holes in the base and...

When I made the upgrade to linear advance and my print speeds went up to 150mm/s, the gears on my Pitan started having issues with cracking. I designed a small gear with a cuff with an M3 retainer nut and made a thicker mount plate for it to fix...

The Tile_D is made to work with the 50x50 tiles from my floorpack.(https://www.thingiverse.com/thing:3895156) ________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Tinkercad...

This helmet can support the following: - A suite of Picatinny rail compatible side attachments from Halo: Infinite and Halo: Reach - A flat, universal overhead mounting plate - Multiple UA attachment upgrades - A suite of legacy ODST attachments -...

For me it was clear, there must be a successor and here it is.The body kit for the MK3 and MK4 series is a purely optical upgrade which is designed solely to ensure that you have even more fun with your printer! It is a solid model which, when...

Note: this version has less “ample” room than before, so take that with a grain of salt.Details of my upgrade of a LowRider v2 to v3 are available here on the V1 forum.Print and Assembly:Print the parts as oriented. No supports needed, assuming your...

I often want to upgrade parts on my prints and glue prevents that. My boys also tend to break things ... being able to reprint the broken part vs the entire model is a plus. Except for the charging ports, no glue is needed. All the STL files...

Due to the side mounted design the results are better IMHO than other direct drive upgrade kits I have previously purchased. However, the increased weight of the direct drive assembly does cause some minor artefacts to the surface quality in...

Since I upgraded my Titan Aero to the Volcano Hotend, no fan ducts I could find convinced me. Most were printer-specific, some did simply not cool good enough, and nearly all blocked mounting positions for my DC42 IR Sensor (which I love). So, I...