arduino models

License ------- The "Crystal Generator" models (.stl) are licensed under the [CC BY](https://creativecommons.org/licenses/by/4.0/) license by [Code and Make](https://codeandmake.com/). The "Crystal Generator" code (.scad) is licensed under [The...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

After sanding the putty flat, paint it using model paint or cover it with a large sticker to conceal any imperfections. Test fit the Laforge diversity module into the hole where the old receiver used to be. Cut off this standoff because it's...

You will, however, need to modify the hole in the motor arm to fit your motor's shaft, after you have scaled the model. You may also need to do some modification to the connector arms so that they clip nicely to the connecting rod that you plan to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 79...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

This is a set of models, minus one piece noted in the instructions, for a minimal cutting body modification kit for the Adventure Force Commandfire by Dart Zone. Print instructionsForward I am not the most advanced 3d printer user. I printed these...

This station involves three separate 3D printing processes:Main housing (220mm x 220mm)Rotating disc (172mm in diameter)Gears, gear holder, and "engine" stick componentsMotivationThe primary motivation behind this design was to facilitate the...

To this end please be sure to down load the most up to date model files before you start printing as things may have changed. Slider Updates include 1) Processor upgraded from RF-Nano to much more capable ESP32 2) The Nextion display is no...

Note that the Shapeways model has been modified to meet their minimum wall thickness requirement, so looks a little different; it uses the same idea. You'll need to order two if you get it from Shapeways, since it's only half the puzzle. On the plus...

For example, if you shower pole diameter measures 22mm, try a Pole_Diameter value of '21'. Material We recommend printing this holder in ABS filament for extra durability. Versions 1.0 (5 Dec 2020) - Initial version Printing Recommended slicer...

 The cable was routed to the reoriented Z axis Cable Chain and routed through the new Z axis belt cover on the right side of the printer to the U2C USB to CAN adapter,Finally, the U2C adapter was connected to a freed USB port on the RPi.Fusion 360...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 45...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 6 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

... satellite. The team’s website is http://csdc.uvic.ca/ Note that I did not create the Diamagnetic Payload Assembly, this was created by A.G.O. Environmental Electronics Ltd. The magnetorquers are not in the model, as they are still in development.

License The "Bitten Doughnut" models (.stl) are licensed under the CC BY license by Code and Make. The "Bitten Doughnut" code (.scad) is licensed under The MIT License by Code and Make. Note: 'BSD' license has been selected as it is the closest...

Designed with SketchUp, fixed with Microsoft 3D Builder, sliced with Cura and printed in PLA on my Robo3D R1+ Parts: Some kind of power supply with a 5.5mm plug A 5.5mm socket (from AliExpress "5pcs/lot High Quality Socket Female Panel Mount...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

I am now only weeks away from getting my own printer :) but in my preparations, i found, that i had used an inaccurate BTT filament sensor model, in my design. It was pointed out to me that i never mentioned, which panel thickness i planned...

 For me, it pressed in very tightly; if in doubt, glue it in.To mount the holder, I stuck this adhesive mount onto the back, and used it to replace the jaws of an older model of this suction base.  The adhesive mount’s socket is smaller...

I propose a modification of the original model to be able to use clear plastic plates. Thus it is possible to see the interior of the enclosure. The screw fixing makes it possible to make the enclosure completely removable. ## Materials...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: Divine Awakening] The last child of Minera to rise from the ocean depths as a great landmass. Tharador is the smallest of all continents and most meager...

... glad to finally get this published. Any questions about the historical nature of this set can be addressed to Simon at the email address above, and I will try to answer anything on modelling or future edits here in comments. ... -Ian R.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

I have completed assembly and everything works so this addresses some of my main wants for this awesome model. I am also going to include the full parts kit here (the originals I used also), so everything you need is in this one thing saving any...

I RECOMMEND THIS ONE INSTEAD:https://www.printables.com/model/169138-prusa-mini-detachable-cooling-duct-assembly-v2 About this modI have never been happy (okay that's a lie, I was happy for the first few weeks) with my Prusa Mini's cooling. This is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

The Aim of this project was to build a converter kit for my V2 model into a Core YX printer and by reusing as many original parts of Ender 3 v2 as possible. The second goal of this build was to keep the possibility of converting back the coreYX to...