arm phone holder 3d models
441292 3d models found related to arm phone holder.youmagine
With a simple push from your wrist, the phone will come out to easily grab afterwards. ...The One Plus One phone can be positioned facing up or down, depending on the user.
cults3d
I needed a phone holder and I needed to be able to attach it to a flat or round surface (Table or a baby stroller). I hope it helps someone else too. ... Just get M5x30 7 Pieces and M5 nuts 7 Pieces
thingiverse
All kudos go to CDeviant and igorF2 https://www.thingiverse.com/thing:2505394 https://www.thingiverse.com/thing:3312779 10/2/2019 Edited to make the slot slightly larger to fit the original creators phone and tablet slide. Added mount with 90 degree...
thingiverse
This is a phone clamp that can be used to mount a phone (or whatever) to a spring loaded microphone boom arm like the Innogear or even an expensive Rode PSA1. You can go to amazon or aliexpress and search for "boom arm", and sort by price to find...
prusaprinters
It requires no extra parts (besides the boom arm). To Assemble you will need to print the following: 1x Mount Rod 1x Frame Bolt 1x Clamp Frame 3x Nut 2x Clamp Tooth (short or long) The LONG Clamp Tooth fits any phone/thing that is 91mm wide. If you...
thingiverse
I designed this to use an X-Mount i had lying around, simply get an M5 screw of about 36-38mm and an M5 nut and it's done! ... This is a modification/addon of this thing: https://www.thingiverse.com/thing:2448971
prusaprinters
Loved this design for the most part but coundn't charge my device whilst in use, so modified the clamp arm to allow for for charging in use. ...I also shortened it slightly, which prevents the clamps from pressing the bixby/volume/side buttons</p>
cults3d
Original mount works great but stock arms were interfering with power button of my Samsung S9+. Extended arms by 20mm and 40mm 20mm works for my S9+ 40mm should work for larger phablets. ... Also uploaded extended version of mounting clip here ...
thingiverse
Original mount works great but stock arms were interfering with power button of my Samsung S9+. Extended arms by 20mm and 40mm 20mm works for my S9+ 40mm should work for larger phablets. ... Also uploaded extended version of mounting clip here ...
cults3d
Generic cell phone mount on 140mm arms each with screw-on base and screw/nut method grip on cell phone (impossible to fall off). The number of arms is at the whim of whoever prints, I just recommend that the more arms, the larger diameter arm/arm...
thingiverse
Instructions for 3 sections long arm: * using **ABS**, print all three `rotating table plate - *.stl` parts * 60% infill (can do less, but this is what holds everything in place when arm is fully extended and you put a big phone in it!) * using...
prusaprinters
The arm is meant to work together with this phone holder: https://www.printables.com/model/286824-car-phone-holder-for-oneplus-7-proPrint it in PETG to prevent it from warping.Credits to original modelMINI F56 Speedo Rear Phone Holder by...
thingiverse
... should accommodate an iPad with case attached. Just whipped this up, might want to add a wooden dowel for stability between the arms but not sure how much rocking it will really experience. ...Leave comments if anybody would like to see variations.
thingiverse
This is a simple, but very resistant phone holder for arm stand. I've modeled it for an old arm lamp that I've reused for this purpose. Only hardware you need is: - x1 M4 Hex bolt - x2 M4 Nuts One nut is for tightening knob to bolt, the...
thingiverse
I've extended the upper arm by 20 mm to easily fit a wider phone, and allow for shorter springs :) What a great model, thanks for sharing. ... I've added the STL, the FreeCAD model that the STL was exported from.
thingiverse
Remix of https://www.thingiverse.com/thing:1526933 80mm 3 Arm version
thingiverse
This arm is really flexible. One joint can bend 180 degrees. Prerequisites: A 30 mm (or longer) M5 screw with a nut, for each joint you want. The setup on the photo needs two. Print with 2 mm walls/top/bottom for stability, and in a fine...
thingiverse
this is my first design towards helping with everyday life the design is made for the Nokia model TA-1323 with case on it
cults3d
this is a cell phone holder with adjustable arm to use cell phone as a camera for 3 d printed object or as timelaps you can use him to monitor from the front of your ender 3 or with 2 v slots to monitor from the side of your ender everything is...
thingiverse
Use 9/32" or 7/32" compressions springs for arms, and small extension spring or rubber bands will work for the cell phone holder. Instructions 1. Place arms toghther. 2. Place pressuer plate in slots in on male end of arm. 3. Place spring in...
thingiverse
No disassembly required to insert/remove the phone or to adjust the phone rotation or pitch. Might not fit extremely narrow phones - minimum width of the grip is 72mm Update 4/2/2018 Added another degree of motion with the Elbow parts! ...Finally tilt...
cults3d
Cell phone holder with coat of arms of rhineland-palatinate https://www.tinkercad.com/things/4ybYucAcLMh
thingiverse
I wanted a long gripper to hold my phone height-wise, and also my ebook-readers. Should just barely fit 7" tablet/readers (eg. ...Kindle Oasis), but comfortably fits 6" (Kindle Paperwhite).
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/aVBPRFRZaTo
thingiverse
I used the original fill but I added some part to the claw, make 90-degree angle and add a 200 mm arm to the model. The model work but you need to use sand paper to make it fit. The screw is 95% on the x and y axis. The full kit’s part is all the...
thingiverse
... is set for horizontal mounting. Instructions I used 10-32 x 1" screws and nuts with washers for mounting the holder and mounting bracket to the central arm. The phone holder is best printed with the mount arm pointing up. ...Supports are required.