armored mewtwo model

I still have not got this model right, the results are not really satisfactory. Maybe I don't have the ball geometry figured correctly or the latitudes measured properly. Sometimes the slicing does not join the detent teeth skirt properly to the...

A commercial milling machine costs at least about 1000 usd / eur and even the smallest models are too big for my small home workshop. This router is slightly larger than a proxxon, smaller than a commercial type bf16 router, and costs about half...

After way too many iterations and many failures, I'm happy to share the final design with everyone who also loves mechanically moving objects.Before we jump in: This model was heavily inspired by the work of David C. Roy (credit to him at this point)...

Small October 2022 Status Update (original models generated July 2021): I've made a couple of these and they've held up well - after over a year of light daily usage, they still work!This is M42-4-E-Var, a focusing M42-screwmount to Sony E lens...

instead other models of TMCxxx , No solder iron necessary, you just have to rotate the connectors receptacles on the motherboard with a simple leatherman tool.like on this video Be care, some of the latest motherboard doesn't have support under the...

My practice showed that such a simple model works even better than the previous one. I think you can print such things for your girlfriend or wife and thus show that your 3D printer does not stand between you and it helps to strengthen your...

Then slide the little clip (that's included with the Vertical Stand model) down the back of the Wall Mount (long side pointing down and farthest away from the Wall Mount) until it slides over the back side of the Vertical Stand. It's purpose is to...

**5** Shift Knob (Optional) I have NOT tested this as I opted to use a real shift knob, but the model is there if you really need it. I would suggest printing it upside down. **6** Pivot Pin & Pivot Cap (Optional) These are only required if you opt...

Specifically, the mouth utilizes inexact measurements, and inconsistencies in source models from the 3D printing process made it difficult to gain a good measurement. On the sketch, we measured the mouth to be 1.20cm from the side of the constraint...

# Supplies you need to buy: 1 Logitech M510 Mouse (this model exactly) https://amz.run/67er 2 Philmore push button switches https://tinyurl.com/mr42ce4n Solder (lead is easier to work with) https://amz.run/67nL Wire https://amz.run/67f4 Super...

Winston sculpted reproduction of Schwarzenegger's face in several poses out of silicone, clay and plaster.[41] The sequences set in 2029 and the stop-motion scenes were developed by Fantasy II, a special effects company headed by Gene Warren...

Externally modeled accurately from my real life Amiga 500+. Video of Doom Eternal on it: https://youtu.be/lsHi1vf_0Z4 Advanced project for builders that know how to fabricate some things like cables and adapt and paint parts to fit their hardware....

If you don't want to mess with a PLA support, you could probably print this part in two separate objects.I provide you the Fusion 360 file, so you can customize and change the model according to your rail system. I strongly recommend you to...

Parts Required to Complete:SmallRig Mini V Mount Battery Plate with Belt Clip 2990V Mount Accessory Plate (3D printed or from SmallRig MD2801)M3 x 6 Flat Head Screws (3)Battery StrapVelcro, Servo Tape, or Non-Slip PadWhy I Made This:I recently...

Z gap between support interface and model is 0.2 mm For the adapter plate I used standard supports with the same support options Other parts: For convenience, I included the 40 mm fan cap, part cooling duct and BLTouch mount from the original...

Verify the axle turns freely. Source File FreeCAD: BearingPegV4_2019.FCSTD Reinforced Within the pegs (excluding the original V4) 'pins' are embedded that promotes a strong cross pattern with lines at the stress point in addition to beveling....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Also, no screws or other fixing methods are used. How it works can be seen in the video UPD I added a version in two sides in the form of frames, its printing a third faster and when printing a model, corners closed by cooling by a fan are not...

This is because it is a slide on design to limit the complexity of the model.  INSTRUCTIONS: I tried my best to make this the simplest adjustable optic for nerf yet! As such it has only 3 parts that can easily be printed in under 2...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers).For adjustable friction, I've added a simple bail that attaches to...

Just copy your gcode to the same folder as the exe, run it, select the options you want and when you've confirmed your choice it will automatically open the first gcode in the same folder and write the temperature changes for you.Extract...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

A customized version of this Thingiverse model (http://www.thingiverse.com/thing:46884) was created using Customizer. ...The STL file options include: qr_rotate=0, add_sub=2, hole_r=10, hole_y=0, hole_x=30, corner_num=1, qr_thickness=5,...

Links Here are some useful and fun resources: - The Docs (SlimeVR Documentation) - Github Repository SlimeVR - Github Repository Hyperion - Thingiverse Hyperion (https://www.thingiverse.com/thing:5186756) - Cults3D Hyperion - CGTraders Hyperion...

Luckily, this model is not in tune anyway lol. Post-Printing Even at 0.06mm and surface-oriented settings, I have found that the interior surface of 3d printed woodwinds is still not smooth enough to get a really good timbre. To fix it, you could...

[Video](https://gitlab.com/jdobry/hevo-mgn/-/blob/v3/DOC/video.md) ============ [](http://www.youtube.com/watch?v=EZKwii39ZXY "Video Title") [![IMAGE ALT...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

Also, this particular model has a bunch of different colors to really pick your perfect cart! What You'll Need ExtraParts:4x 14" long, 1" OD PVC pipe [355mm Long, 25mm OD] (theoretically the metric standards available should be identical) Note:...

COMPATIBILITY ------------- This air assist fits the 20W "Vigotec VG-L7" laser, also sold as "KKmoon BX20" (2021 model). That's a diode laser with Ø15mm focus ring. The focus ring is 10mm high. ADJUSTABLE Z AXIS REQUIRED ...