attack on titan game models

To complete the build you need: 1x a snap off blade 18mm x 100mm 6x M4x10mm screws with nuts and washers 1x M5x20mm screw with self locking nut and washers 2x M3 screw with nut and washers 1x ballpoint pen spring 1x a piece filament as guide for the...

With default 1.8mm thick spring it works in range of 0.39 - 1.06Nm (depending on PETG manufacturer spring stiffness will vary). You can switch springs if needed to change Nm range. Now I only included 1.8mm and 2.05mm springs. Will upload more...

Ender 3 pro psu cover with RS5V psu for Raspberry Pi this is my solution for upgrading the psu fan with an always on 80x80x25 Noctua the original thermal controlled fan is mounted too, but was never needed so far the electronics of my Ender 3...

No more primeline scraping, no more looking for leftover primelines in your printer, its all being collected in the tray at the front and all you have to do is to empty it out when its full and can see stuff being kiked around by your printer!Here is...

Total weight for the open version without cable is only 325 gram with non existing pressure on head and ears. What you need?! In total for both cups: - 8 x M4 Nylon Washers (1 mm thick) - 4 x 11 mm long PTFE tube 3x4 mm diameter for hinge >...

Post-Printing: Step 1: Ream Holes Reorient the part on the print bed so that the clip cylinder is vertical. Print with supports and a brim. Once the part has finished printing, notice it has two holes that need to be reamed to 5mm diameter for...

For best results, these are printed on a 2 layer Raft with Supports. I've also included the GCODE for the battery cover as this looks best printed upright (vertical) with a 3-4mm Brim for additional support. Printing the battery cover upright ensures...

Overall, the support has a lean style, a bit “naked” so no coverage but sweet on the curves, trying as always to enhance the aesthetic side as well. As with other kits, this one is divided into several parts to make it easier to mold and come out...

This design, based on replaced Ender parts. I had the board, screen, hotend, fans and the stepper motor. I only paid for the PSU 15$ and screws 15$ and the filament 20$. So at all it cost me around 50$. When you have some outdated 3d...

My colors, even though the same weights, do not match what was seen on the Diamond Hotend webpage above. This could be because I'm using opaque colors and perhaps they are using translucent colors or it could be due to variations in filament hue. I...

By default, the print comes out at 8 inches, or 20 centimeters tall, and was scaled so the largest piece could be printed on my photon with some wiggle room. TO BUILD You will need to print a set of parts that match. Some of the parts are...

The children were all summarily spanked, told they shouldn't be running around on the streets at night screaming curse words, and they definitely needed to pay back the poor barkeep for stealing his cask of Buttersweet Strongdraught. The bard was one...

Hardware Requirements: (2) 8/32" x 3/4" Flat Head Screws (2) 8/32" Nuts (1) 6/32" x 7/8" Socket Head Screw (2) 6/32" x 1/2" Socket Head Screws (3) 6/32" Heat Set Inserts Cricut 2001401 Deep Cut Blade and Housing Cricut 2001974 Adhesive Cutting Mat...

To fix this problem, I changed the handle to have several arches that give more support as it prints but also allow for many ways to firmly hold the Soap Keeper depending on hand size and strength. I also flipped my design upside down so the largest...

This design, based on replaced Ender parts. I had the board, screen, hotend, fans and the stepper motor. I only paid for the PSU 15$ and screws 15$ and the filament 20$. So at all it cost me around 50$. When you have some outdated 3d printer...

These include:More grip varientsExtra strong grip mechanismVariety of base sizes for different body shapesNon-strap on versionFully 3D printed version with no hardwareThese iterations should be complete soon!Other NotesIf you have any requests for...

The little rectangle holes on hinge1 and the cableguide accept 3mm zipties to secure the cable. Ziptie the cable to hinge3 (just wrap around the whole thing), hinge1 (using the left ziptie slot) and the cableguide (using both ziptie slots). Then run...

In this case, it was the question: "How do I stabilize a bottle of sparkling wine, Robby Bubble or any bottle up to <86mm in diameter so that it can be used as a starting point for a firework rocket on New Year's Eve without it tipping over and...

If you like my work please consider supporting me on Patreon. Become a Patron! ... Tinkercad link: Might add this later Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool...

A wanton disregard for what other people consider reasonable You can find more info on this in this reddit thread. Additional Notes: 1. I had to extend the cable for the MPSMs controller by splicing in some extra wire. It was a super tight fit...

Placing the Module in the position shown in the picture has greatly simplified the tangled web of cables.\n\nI'm currently working on a remix of this design that incorporates a locking system for the Module hole.\n\nIt's recommended to print the test...

Since having the 12mm section (in black) next to the final end-block (in gray) on the power supply "looked so good" to me, I printed another 12mm section and glued one to each end-block.These 12mm sections are not needed but I though the "adornment"...

There are many negative consequences to having the ability to print anything we want at home, including: 1) The ability to tax the sale of goods (in other words, how will governments be funded) 2) The ability for anyone to make a working gun or other...

With a bit of research I realized my mistake and created a revised print configuration based on a modified PETG configuration. With this new print configuration I am now getting very good results, and I invite others to test this...

(not too much) Wait until it begins to harden, remove masking tapes from cameras and apply the contact lenses on top. 8. Buy 2x #6-32 x 1.5" crews and insert them from the back of the eye plate. (This screw will be useful in the future to adjust the...

2019/08/31: Added a zip file with a small modification on front to be used with my Zaribo Linear Rails 15x15: https://www.thingiverse.com/thing:3835170 2019/09/01: 1) Added a square nut to secure better the up_sensor parts. 2) Improved the IR...

I've attached pictures on this thingiverse post which features the downforce at every adjustment angle for the front wing, along with the rear wing both at 100mph. Removing the endplates from the rear wing should reduce its downforce by about 1lb @...

Http://www.thingiverse.com/apps/customizer/run?Thing_id=193647 Instructions Using The Following Options: Resolution Nuts Diameter Point = 0.5 Outer Diameter Nut Thread Diameter = 9 Nut Type Selects Wingnut, Thread Length Point Degree = 45 Countersink...

I have personally tested the Slingshot by stepping on it (80 kg+), and it showed no suspicious noise or cracking, so an infill of 50% should be sufficient for a draw of 20 kg. However, if you plan to draw more or widen the tube channel than...

If you want the head to be centered on one of the purple sections, choose the normal Top version. The Standard Top can be turned in enough different orientations to match up to either one for the remaining heads. The Silver Insert and Cables Insert...