b17 model

As provided the enclosure is set up to accept a 9.7" 2048x1536 panel as used by some iPads - Model No: LP097QX1-SPC1 https://it.aliexpress.com/item/1005002113658592.html There is no reason why you couldn't use any alternate panel and suitable driver...

I added a switch at the bottom of the right arm (super easy access).Please note, this system is designed to be mounted on an aluminum profile with a total width of 300mmPrints without support!Here you will find the links to the creations that have...

...Composed of two pieces - a base for the motor and a cover - the protector fits perfectly on your pistol model, keeping your magazine safe and protected throughout the action. Don't let a lost magazine ruin your play - get our magazine protector now!

THIS MODEL CAN NOT BE SCALED DOWN. Full wing on its way soon. Enjoy. :) 1/12/2022: So I have completed the NAKED stress test today, and the results are remarkable... At 4.3kg of load placed in center of wing, with the external wings held between 2...

If you are using ceiling pipes, I've modelled the right side of the pipes only. For the left side it will need to be mirrored in the slicer. The vents part is optional but I recommend glueing it to the roof. The vents piece can act as additional...

The VR Box comes with pads that may fit your need here. Even if my model provided screw holes and additional holes to fit the screwdriver through, I do not recommend using them. The pillars the screws were originally drilled in are most likely...

# What you'll need This will work with any CH340 USB-serial chip I think, but the model here is for the CH340N for USBC. A picture of the exact chip is given. I ordered one from AliExpress for about $3, and one from eBay for about $6 (because it was...

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

Deck furniture is always a good way to add interest to a model. You might want to install a waterproof switch somewhere on the exterior to save having to unscrew the whole deck every time to turn it off and on. Enjoy sailing your Pocket Boat,...

Components used: An SG90 9g servo motor: https://www.amazon.fr/AZDelivery-Digitales-Micro-Servo-Parent/dp/B081Z5V3M2 https://boutique.semageek.com/fr/104-micro-servo-tower-pro-sg90.html?search_query=sg90&results=1 a paper clip glue to assemble the...

The Tunnelplan Wind Turbine is a 1:10 scale model of an existing wind turbine. The diameter of the rotor is 2000 mm (20 meters) and the tower height is 1200 mm (40 meters). the max.ceiling height inside the house. Solution 4 energy...

To split it with ease, right-click on your model within Cura. When preparing your parts for printing, make sure flat sides are aligned downward. For a smoother print process, consider setting 0.1mm layer height and 40% infill as defaults. Here is...

This is because it is a slide on design to limit the complexity of the model.  INSTRUCTIONS: I tried my best to make this the simplest adjustable optic for nerf yet! As such it has only 3 parts that can easily be printed in under 2...

The problem is that the individual mirror cells overlap and when I separated the cells into parts of the larger array, each cell along the perimenter got the full width base perimeter border and so they bump up against each other instead of...

I have no immediate plans of adding a mount for a counterweight because everyone will find differently shaped ones _____________________ **Edit: ** Added an adjustable version of the speaker caps and a locking buckle ___________________ I wasn't...

AnyCubic Photon Heater with Optional Light Models for for the Left or Right panel For the fan I turned it around after I found it not blowing outward. Double Check You use the right top and back that go together. Don't do Like I did in the...

In Ultimaker Cura you first have to install the “Mesh Tools” extension which allows the “Split model into parts” action.Pneumatic tubes with outside diameter 3 mm are used. E.g. Festo PUN-H-3X0,5-NT. Locate the four holes in the housing and enlarge...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

Make sure to follow me to get a notification when it's uploaded!*** ------------------------------------------------------------------------------------------------------------- ###READ BEFORE PRINTING!### * First of all, this is a non-commercial...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

Also, this particular model has a bunch of different colors to really pick your perfect cart! What You'll Need ExtraParts:4x 14" long, 1" OD PVC pipe [355mm Long, 25mm OD] (theoretically the metric standards available should be identical) Note:...

If you use the F3D files, go easy on me as I've only been using Fusion 360 for a month and its the first time I've ever been exposed to 3D modelling. I'm sure there are faster, more efficient, and proper way of doing things as oppose to the way that...

 900mm in length (shown in the picture is a bit too long, you may want to use 800mm instead)The bamboo skewers seems to come in different sizes, so use the file that closest match the skewers you have and scale the model accordingly.  If...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 3 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

... and presupported version. This product contains the following parts: 32mm Base 40mm Base Balthazar Morris DnD 5E Datasheet Get a 40% discount on this model by joining my Patreon! You can also order physical copies at my shop on Only-games! ...  

For the extruder I used from: https://www.thingiverse.com/thing:2735475/files cable-holder.stl https://www.thingiverse.com/download:4650325 extruder-cover.stl https://www.thingiverse.com/download:4650320 extruder-idler.stl...

UPDATE 09.08.2022 •changed length for diffusor and mount from 10mm to 100mm •orientation changed for some models •added end cap UPDATE 12.08.2022 •added with diffusor / without diffusor comparison photo and electronics box wiring photo •added...

If you don't want to mess with a PLA support, you could probably print this part in two separate objects.I provide you the Fusion 360 file, so you can customize and change the model according to your rail system. I strongly recommend you to...

Just copy your gcode to the same folder as the exe, run it, select the options you want and when you've confirmed your choice it will automatically open the first gcode in the same folder and write the temperature changes for you.Extract...

SECOND NOTE: I made some corrections to the actual model after I printed it. I got my first attempt working, though it's not perfect. For example the shaft broke off while putting it together. I tried to make it a bit more robust, don't know if that...