balloon snake step by step 3d models

CHAINS AND NECKLACES: Chains: A timeless symbol of elegance, Cad Cart's chains and necklaces collection features meticulously crafted designs made possible by precision CAD files. Mangalsutra Necklace: Experience the fusion of tradition and...

This will be held together by 1/8 rope or rubber band. Note: found that rubber band had too much give to them and used rope and pin through CF tube to lock the wings as if where glued Additional Access: I used the door hooks to attach to the wing...

The mickey parts where remixed and mostly rebuilt by me from the original google mini thing, the echo base was remixed and rebuilt from : https://www.thingiverse.com/thing:3337820. Options - print out a second set of ears for a fuller look -...

CTR_eye_a.L and CTR_eye_a.R controls the dilation and miosis of the pupils by the customized attribute—pupil. There is a facial control system to create facial expressions. There are more controllers of the body which helps create more detaild...

4- The model stands by itself using the print parameters noted above. If a higher infill is used on the head, the model may become top heavy. Use your discretion for different printing parameters. I would suggest higher infills for all parts...

Instructions If you plan to print in ABS, scale the object up by one press of the up arrow or the case will be too tight. ... Using the following options: 5width = 58.6 5height = 7.6 iphone_version = 1 4_per radius = .3 pattern_rotation = 10 5cornerR...

This project is limited only by the visual range where many PIR and Ultrasonic sensors have a limited range. This works great for projects where you want to detect a cold object (not a living body) or objects far away. The base code uses a 10...

Rosie the Robot, from the cartoon The Jetsons, by Hanna-Barbera. Rosie is a robot and the maid and housekeeper of the Jetson family. She is a model XB-500, an older model, but the only one U-Rent A Maid had that Jane could afford. There is an...

The factory sealed, hazardous location fixture is protected by a copper-free aluminum housing with an epoxy powder coated finish.The EPLC2-LB-50LED-RT-600V is a Class I, Division 2 and Class II, Divisions 1 & 2 hazardous location light fixture...

You will lose about 1CM in the Y axis by using this as it is. That's because it pushes the nozzle contact point ahead about that far. Worth it. Do adjust your slicer and firmware as needed. You DO need to print the 5mm spacers to run two of your M3...

I did this by pressing with my thumbs, but gentle tapping with a tool may be necessary. Using a second bearing as an extender on top of the first may help. Press one bearing into the center hole of the Perch Swivel Platform. Put a bearing at each...

Print Settings Nozzle size = 0.3 mm (Should be printable with 0.4) Layer height = 0.2 mm Filament change layer for colours on "FlatBase.STL": 1) Start (Parking lines colour, mine is in yellow) 2) Layer 4 (Overall base colour, mine is in black)...

I want to mention the "Ultimate Massive Darkness 2 organizer - Sleeved Kickstarter Edition" by WingsOfDaidalos: https://www.thingiverse.com/thing:5268184 I took "massive" Inspiration from that, especially the idea, that you put all class specific...

Please print the tester to check your printers calibration and settings. If the parts appear to be the wrong size, you might need to scale those by a multiplier of 10. General Print settings: 0.2mm layer height 20% infill 3-4 wall line count Part...

you can trim the friction one by cutting the tab that holds down the servo on the top plate. I used xmods shock screws because they had the non threaded section in the sliding part of the linkage. you can drill out the linkage so that it the screws...

It should be almost the same with the stock Anet firmware, and similar with Skynet3D (Marlin)\nWhen you have tuned your heater properly, the temperature will fluctuate by just plus/minus 0.5 - 1C and will be very stable.\nNotes\nActually try it...

I painted all my pieces (A, B, and C) before assembly and began by sliding B (mid piece) into A (grip) and positioning them where I wanted. I then pushed C (muzzle) into place--this required a lot of twisting and heavy pushing to get into place...

I eventually found that without making any code changes, you can simply wire up a switch by using any ground pin, and then the D3 pin. I tested it out on my breadboard and i was ready. The hole for the shaft of the momentary push button is 7mm...

Please print the tester to check your printers calibration and settings. If the parts appear to be the wrong size, you might need to scale those by a multiplier of 10. General Print settings: 0.2mm layer height 20% infill 3-4 wall line count Part...

If necessary use a hobby knife to trim any parts of the center block if fitment is too tight. -Be sure to install the rear battery strap through the cover's strap hole before sliding into place so you can easily remove the cover later by using the...

I wanted a good DIN Mount for my Shelly Switches to mount them properly into my electrical box, but all that i found did not really satisfy me.So i made my own inspired by severel other designs with these key features:vertical orientation to save...

Some glue holds it from slipping Finally, attach the end of your cord to your parachute. Setup: Look up a model rocket parachute folding technique online so it actually opens when you try it, then put some Glass Fibre wool (if you have some) into the...

Unfortunately I can not upload those files here - but it is not design for easy reproduction by others anyway… Here is my schematic - just for reference: Happy printing!If you like this design, then please leave a like and also post a photo in...

My Toniebox ferris wheel project: Inspired by Sascha Weyh his big wheel, I wanted to know. After a year as an active hobby 3D printing fan, I ventured into the first big project. Since my son has a static passion for Tonie figures, I had an idea...

Determine the center position by connecting the controller with your PC and adding it as a MIDI controller to your DAW or VST host of choice. Turn the pot until it is in center position. 12. Slide the knob onto the pot so it is centered. Tighten the...

In this version that I have uploaded I think it is already fixed, if I have put the center of the hitch coinciding with the barycenter (or center of gravity) of the triangle formed by the three screw holes. I hope this fixes it, but I haven't tried...

which can also be achieved by not using a fan at all.the pincer: This crab-pincer shaped version is supposed to have decent airflow just below the nozzle while not obstructing the view on the extrusion. This one works kind of. Still not...

My design can be turned on / off by sliding the battery forward and back, the light will stay on when in the forward position.my design is also one piece, making it quicker and easier to print and assemble.You will need:5mm LEDCR2032 batterya small...

The reliability of the more sturdy DC15a/s weapons was something that would have been addressed by final production were the project not ultimately scrapped. The X project was ended as a result of a combination of factors: The formation of the...

Turn the knobs until the tube is placed straight in the middle of the hole and held firmly by the steel tensioner. The vice: insert two M4 nuts into Gnist2-vilce1 part top. Screw the M4x60mm threaded rod with the knob all the way trough the two nuts...