borg computer case 3d models

Put new assembly together with the Main Body (Again, please make sure it can move over the main bolt freely). Tighten the screws so the gap between the jaws is 39-40mm Enjoy your new clamp!  Longer boltsIf the 80mm bolt is not long enough you can use...

I looked around thingiverse and didnt really see anything I liked so I designed my own.These tensioners use the stock rollers and T-nuts, etc that come with the machine, but you will need the following additional hardwareX TENSIONER1 - M4 x 25 CAP...

I opted to include screw holes but haven't used them, I'll save that for when I decide the best place to mount it. I also went back and finished the initial design to slide up a leg and mount that way, although I haven't printed it I'm 99% sure it'll...

I've also included a piece named "hero Riser" which is basically just a rim you can glue to the top of the original hero tray, just in case someone else makes the same mistake I did and mixes up which one they're trying to print. Since I'm now...

You can do this by using 0.1mm layer height and then rounding up (for example to next 0.1mm or 0.2mm - or even 0.4mm or more in some cases) until you are satisfied. If your printer is calibrated exactly, this won't take long to get to but it is...

I am not sure what to suggest here other than tweaking the position of the touch panel if the screen appears to be offset.Printing1.All Casing elements printed @ 0.2 layer height, 25% infill and 2 perimeters. Smaller pieces and both knobs 100%...

In this case sending your own custom GCODE to the printerThe printer does what you want it to do (hopefully) What do you need?2 printed parts based on your desired version10x Tactile push-buttons (6x6x5mm)(Optional) 3x rocker switch (19x12mm)...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

... Resist the temptation to push the whole wheel out this way, the silicone CAN tear or come loose from the hub, in both cases the wheel is worthless. Just keep pushing and pulling until you can get hold of one of the spokes and pull the wheel free.

As for assembly, I wanted to retain the ability to dismantle the blaster in case something breaks. If you don't care about that, you can glue everything together in any way you want. I used some 1.5mm nails that I had lying around as hinge pins for...

I did not use a RTC as per the original design as my home automation server is aware of the time, and when to issue commands.The code remembers and saves the valve position to the file system (spiffs) on the D1 mini, this is in case of a power...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

There are no brims generating unwanted tensions and torsions in this case. I have made them from a 3mm hard aluminum plate. It could keep carriage surfaces parallel and should not be deformed by any unequal crew tightening or temperature I mean. The...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

(especially helpful if you choose to use Powdered Compounds.) Alot of M3 Screws (I would buy a set with nuts) - 8 pieces - M3 x 12 (to screw in the "inner casing") (with NUTS) - 2 pieces - M3 x 25 (for knob) (with NUTS) - 2 pieces - M3 x 25...

But in these two cases, points are not awarded for these cells.The objective of the game is to score the most points.Points are awarded only when two or more sides of the laid out chip are simultaneously combined.When matching the "empty" side with a...

You can technically go up to 20mm, however, they will likely cosmetically damage your SFS case.2x (or up to 5x) M3*8 screws with drop-in V-slot nuts (These printed ones work great!)2x 30mm lengths of PTFE tube(optional) These printed bowden clips are...

As your Reverb G2 casing and the Fresnel lenses are both made of plastic, please use caution and ensure that the super glue is fully dry and that all fumes have dissipated before bringing the assembled Vive Tracker mount in contact with your...

This is a very sturdy wall mount for the LEGO Space Shuttle Discovery - a mighty complex object to put together there - if you don't have a big display case then you wonder where to leave it?I wanted a wall mount that was small and inconspicuous, but...

In the case of counterbore holes for nuts, the corners will be rounded and it will be difficult for the nuts to enter, so provide a small groove to prevent this.The recommended groove width is 0.1 mm.   That's all there is to...

(Text tested to print fine with standard .4mm nozzle) Lots of Capacity - The AA version holds up to (16) Batteries, the AAA version holds up to (25) batteries (I could have made the AAA crate smaller, but i liked the matching set size).Safety -...

nozzle @ 280 degrees Celsius, bed temp @ 120 Other Notes: After a while, the plastic attached to the screw will eventually be worn-out/bent and may be unable to go back to its original state, If that's the case and if the other half of the clips are...

In case the hotend touches the fan duct (which happens from time to time when I change nozzles) the damage is limited.Also I forgot to mention that printing the "pincer" can be a bit nasty since some of the walls are just 0,4mm thin - don't ask me...

I also included a complete body instead of parts in case you don't want to use any glue. This can be assembled with zero glue now. Slot the pieces together and you're good to go. Body part B can be assembled with glue, but you don't need supports...

Extrusion end-cap: https://www.thingiverse.com/thing:398515 and the recently added "alternate" version; https://www.thingiverse.com/thing:4136209 In both cases, only the "plug" part is used, the visible (external) part is my own "design" 2020 v-slot...

Take the front of the PiCam case (with the single square hole in the middle) and loosely mount it to the rotating camera mount. Just a single screw, don't put a nut on yet. Use a 16mm M3 screw to mount the main arm to your X-Axis motor or hold it in...

I did not need that, but left it there just in case.** **Update 24-11-2020: I bought some teethed pulleys to replace the smooth timing pulleys on the X and Y belts, but I ordered the wrong size; too big. ...If you want to see how I adjusted the X an Y...

27.08.2022 - SKR1.4 Turbo Motherboard case added. 10.08.2022 -New photos was uploaded. 13.08.2022 - some STL was fixed (see V1.1). 3D Printed parts: (for bom list and my cost see attached PDF) 1 pc - Left upper belt guider 1 pc - Right...

Other thing that might help is lowering the bridge.I invite You to the adventure of improving this design - print your own and maybe we can make it even better together :)Upgrades 08.03.2023 (gears with string names, secured with conical screw):There...

 Since sharpies come in black commonly and apply well against light backgrounds, this may save you the hassle I made for myself. All-in-one Prints  (special cases)For people who can handle printing everything (including the bookend parts) in one...