borg computer case 3d models

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

In case it is too loose, try increasing your extrusion multiplier. If it is too tight, try reducing your multiplier.\r\n\r\nIf you can't get the top and bottom of the bricks to grip evenly, you may have to open the included .step file. Try using a...

If that's the case, you'll need a 11mm OD bearing with a 12.5mm flange for the pulley. These [uxcell F685ZZ Flanged Ball Bearing 5x11x5mm Shielded Chrome Steel Bearings 2pcs by...

Instructions: Options used: - qr_tolerance: 0.001 - per_h: 10 - per_w: 3 - hole_r: 10 - hole_y: 0 - hole_x: 30 - tag_height: 80 - qr_data:...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

Give your Prusament Spool a new life as a home for succulents, upcycle the side of a Prusament Spool as a mesh in with the succulents can grow and then be hung on a wall for them to live and be displayed. What you'll need Side face of a Prusament...

That unfortunately means the pre-lens distortion file does not work as well for some users and in some cases could be uncomfortable and even cause eyestrain. If that happens you will have to revert to stock or else modify the distortion file...

All will need supports. Printing Wiring If you use a 4 wire fan like the Noctua, you only need the first two wires (power and ground) but I went ahead and brought out the fourth as well in case I am compelled to add a PWM generator to provide speed...

These are advanced level prints that will take long to print and will use a lot of plastic (about 1 kg altogether in my case). Post-Printing What you need Cable 3x 1,5 mm2, long enough to reach your connection point Cable gland for your cable 2x...

I used 42.5" of GT2 belt for the cantilever arm & 31.5" for the 2040 motor but left a little extra on there in case I make it longer. I have uploaded a fusion 360 assembly file as well as a sketchup assembly file so you can see how all the parts...

For any project where motion tracking is necessary: Quadcopters - Quadframes' next goal in this case as far goes, because using cameras in different places such as above head etc which will make it seem like you’re in multiple locations with only...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

They also point less at the nozzle itself but more towards the printed part.This fang also allows the use of a 40x20 extruder fan (in case you want to mount one), instead of 40x10 because there is more clearance space between the fan and the air...

For the rings in this case use only the body so that the marking stands out in bas-relief. Then use the body grouping feature of your slicer befor slicing. Remember to configure your slicer with a first and last layer in a concentric pattern to...

These are referenced by the PrusaSlicer files (.3mf) to modify the print direction so that the flat faces have apparent "pixels" due to differing light effects. I printed 3 of these, the first (shown above) in the silver filament that came with the...

There's only one file here, but just copy it and flip it on your printer's bed to get both halves (I hadn't learned to flip a duplicate of a body in Fusion 360 at this point!)The exhaust panel also uses the 8mm brass tube.The wheel arch liners have...

Have shot nearly a case worth of paint thru these mags. A few chops, but not sure if that is the mag, Tipx or trigger fingers fault haha. I do like that they are somewhere between the TIPX 12 round and the 7 round in size. The 12 rounds are nice but...

Put the pins in the rear holes to prevent it undoing.In both cases, pull the arm back and launch something. The tighter the string or rubber band the more power.</p><p>There are a few options at this stage:</p><p>First of all, you can leave it at...

Given that: I may just run some CFD design cases after dinner... Covid hey?</i></p><p><i>It sure is one of the ugliest vacuums I've seen, so please assume that this project will quietly die if performance is not AMAZING.</i></p><h3>Update, 5 May 21:...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

but in closeup, the imperfections show. I guess Cura refused to slice the thin parts properly, but since it will (in my case) be behind a cover, I'm not going to bother reprinting. Test prints! I dry-ran a print with the stock fan and cover. The...

I'm fairly new to static and have neglected any friction or the weight of the rope, still I think that for small use cases, like here, this doesn't matter.First we'll need the angle of the rope, this only depends on the length of your arm.The angle...

If this is the case, and accuracy is important, you should scale up the dimensions a little bit to compensate. I only tested this for small gaskets. ...If the model proves unpractical for larger gaskets, contact me and I'll see how I can improve it.

I even used a brim on body_top_with_supports since it is such a long print.I used a raft on: eyebrow_left/right, eye_blacks, eye_white_left/right, tail_black, hair 3-The eyes are extremely small, so you may want to print a few in case you lose them....

It corresponds to the spacing of the two pieces necessary to trigger the probe, plus release of the nozzle from the bed (normally the thickness of a sheet of paper), 0.2 mm in total in my case. The assembly takes about half an hour.Designed with...

Old files are in depreciated folder in case someone happens to want them (you shouldn't imo). Sorry for the hiccups.-----------------------------------------------------------------------------LDO Apogee for Phaetus Dragonfly BMS hotend (incl mount...

I'm just going to drill the hole out. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 30% Tri-Hexagon or Cubic Filament: Overture PETG Silver Notes: It's pretty sturdy, but...

In that case, I recommend, "Speaker Spacer Mount Tab" https://www.thingiverse.com/thing:6276734. These could be attached with small screws or glued on. Or break out your favorite 3D modeling program such as Tinkercad and combine the mount tab with...

In order to upgrade you will need to print the following pieces:Spool Holder Kit v2 upgrade:Spool Holder Standard Base Left v2 (qty 1)Spool Holder Standard Base Right v2 (qty 1)Spool Holder Bearing Keeper v1 (qty 4) NEW PARTYou will also need 4...

In many cases, humans serve as the primary interface between users and complex systems, acting as mediators who help explain intricate concepts in simpler terms. This role is often filled by customer support representatives, technical writers, or...