bowden tube clamp 3d models

Here's my idea of a Bowden Tube Clamp to help stop coupler chewing of the tube from constant back and forth movement. Note: clamp part should fit snugly on tube prior to screwing down. I found... r4 clamp works for Capricorn tube and r4a clamp...

...I made this split clamp that holds the Bowden tube snugly with a zip/cable tie. So far so good. ...Don't mind the rough looking innards, I drilled out the hole and didn't notice how bad it looked until I uploaded the photos, but it printed very well.

This is to solve the problem of the Bowden tube moving while printing. I found clips were not solving the problem so I created this. I hope it helps you if you have had the same problem. ... With clip https://youtu.be/Wr5Uji_htBo With clamp...

... Also includes a nut grip to fit better, easier grip, etc... 12mm Bowden Tube Clamp 4mm tube https://youtu.be/qOOcTn0ghAY Nut Grip for 12mm Bowden Tube Clamp 4mm tube https://youtu.be/R3aEX8jG-44 Made for my :- MXL Quick Release Belt Drive feeder.

12mm Bowden Tube Clamp 4mm tube This is an easy* clamp for a 4mm Bowden Tube. The outside diameter of this clamp has a 12mmx1.75 mm thread. Please note the model is set to 11mm diameter to allow for tolerance in the nut grip. NOTE: This may add a bit...

Lacking a spare fitting and being a big believer in the power of zip ties, I designed this clamp which fits in place of the stock plastic threaded piece and allows use of a zip tie (or hose clamp if you prefer) to secure the bowden tube. ...Tightening a...

I didn't want to disassemble the Bowden tube my new CR10 V2 so I sketched a quick strain relief clamp so the Bowden tube does not twist when the X-axis moves. My fittings appear to be a standard size with a 10mm hex which is 5mm high capped with a...

This design utilizing a bowden tube puts significant stress on the tube as the print head moves side to side in the 'X' axis, causing it to be rotated back and forth in the existing self locking strain relief. This rotation slowly wears on the tube...

If you have the slightest feeling that it is moving, it is.For optimal results:Use high printing temperature to aid layer adhesion100% infillSand the outside of the PTFE Bowden tube and the inner sides of the clamp to get better grip between them.Use...

This is version two of a Bowden tube clamp using a nut to compress the fittings instead of a zip tie. I used part of a designby krtektm who also created a compression type fitting. It should fit the standard 4mm ptfe tube and clamp over the...

So I designed these clamps; the plate version replaces the acrylic part on the extruder on the output side and the small clamps are meant for the input side to stop the tube getting pulled to the extruder (happened to me once). ... The included...

Must have been my zip ties but the tube kept getting pushed out. ... I cut the original model to get a 360 degree enclosure around the tube and lifted the center face on one side .4mm to apply more tension.

This is a very simple 4mm Bowden tube clamp that uses an M8 (13mm) nut to clamp the tube. It's very strong, if you do the nut up too much you will crush the tube. I have put a 6mm lead in on the clamp which will screw into an M6 nut or hole. In the...

This is just a slightly modified version of ProtomakerSprint's 12mm Bowden Tube clamp, found here: https://www.thingiverse.com/thing:2537458 I simply added a 6-sided cutout in the bottom of the nut grip part so it would firmly push down into the 6mm...

I make a little clamp for my fittig from the bowdentube. ...The fittig has loosend after a while. The clamp straiten up the fittig so the tube doesn‘t wiggle around. Inner diameter 10mm. ...Spacer 1,5mm.

This is a clamp for "Reverse Bowden" setups. It is specifically designed for a "filament roll above the printer" scenario. Since it is sized for my shelf, you might want to edit the provided .f3d to match your shelf. I haven't tested how strong...

Bowden tube support clamp for the original Tarantula carriage. In some circumstances (high Z or short tube), the bowden tube tends to overflex just before the hotend. This clip snaps directly on the original carriage, providing a more tapered bend...

Bowden tube support clamp for the original Tarantula carriage. In some circumstances (high Z or short tube), the bowden tube tends to overflex just before the hotend. This clip snaps directly on the original carriage, providing a more tapered bend...

Reusable clamps for bowden tubes

... upgrading to Capricorn Tubing and aftermarket push fitting from Amazon. ...this clamps onto the aftermarket fitting and then locks the tube so there is absolutely no movement whatsoever. ...Fits 4mm Bowden Tube push in fittings with a 10.75mm collar.

This replaces the stock lever on the Tevo extruder, and replaces the pneumatic fitting that sometimes looses it's grip on the PTFE tube, the integrated clamp holds it in place firmly. It is remixed from a Flexible filament upgrade that will help...

Originally there was a metal ring and the plastic connector, but after disassembling and re-assembling a few times, the metal ring broke and the plastic connector was not sufficient to hold the tube in place. ...This part requires a few additional bits...

This is a replacement part of the seal from Ultimaker Original - Hot End Pack

Original design worked very well, until thread failed because of heat and fatigue. So I made internal thread instead, where you can screw in M6 heatbreak. Use nut from original design. I used ASA to print it. ...My extruder becomes too hot for...

This is a replacement part of the seal from Ultimaker Original - Hot End Pack

... and the centre of the nozzle to increase work area. FIts the original bowden tube clamp which allows you to use the V6 hotend "Direct" instead of "Bowden" The pictures are from the first proto which had a few flaws. ...The STLs are already updated.

Filament 1.75 Nozzle set : E3d V6 bowden tube clamp Fitting module : https://formersfarm.com/product/fitting NW-C2.0-6P : http://www.devicemart.co.kr/goods/view?no=1357715 NW-C2.0-6R : http://www.devicemart.co.kr/goods/view?no=1357721 NW-C2.0 Plug :...

My bowden tube has come out a few times on prints so this was evolved as a preventative of it happening again ( and is much better than dealing with stock ones. I changed filament towards the end of the Spiked nut to have the 2 color effect. ...

My reprappro bowden tube would occasionally come out during a long print, which is a bit annoying! So, I printed two versions of a 'clamp' that simply holds the tongue (clip/lock ??) down but has enough bend to still lift the tongue out when needed....

Hello, I found similar bowden tube lock on this site, but it was very fragile and it tends to crack when overtightened. I designed my own bowden tube lock which uses one 3 mm width zip tie and it's rock solid (don't mind another zip tie on the...