bowflex selecttech 552 series 2 disk 2 3d models

It is an incredible organ that works tirelessly 24/7, pumping over 2,000 gallons of blood per day. The heart is made up of four chambers: the left and right atria, which receive blood from the veins, and the left and right ventricles, which pump...

PLEASE WATCH  THE HOW TO VIDEO ON THE BOTTOM OF THE PAGE!!There is a very important step many people miss out on and like that the Lifesaver is not correctly  mounted into the case and will fall out eventually.The upper and lower lip needs...

The color thicknesses and the width of the outline stripes on this test print match the stripes on this case and future cases I upload will probably use similar...

* I scored brass sheets in adjacent rows of 1/2” widths, marking 1/8” spacing between rows for cutting with tin snips. * All holes were marked and drilled before cutting out the rows and individual pieces. See below. The uncut brass sheet was...

What I want is a similar setup, but instead of a bespoke console panel setup, it would be very nice to have a replica of the original (3-1/2" high 2RU) PDP-11/03 bezel and console that is the same as the original in size, switch paddles, LED...

http://www.thingiverse.com/apps/customizer/run?thing_id=310541 Instructions Using the following options: panel_shape = 0 grid_size = 0.3 orientation = 1 pixel_size = 0.699 mode = Compile pixel_elongation = 1 pixel_shape = 4 picture =...

April 2, 2016 - Posted additional shots now that I've got the tray completed. The dividers didn't come out exactly as I'd like, especially any divider with text. Holes are easier to print than posts in this case; the shields/computers are barely...

You can also see the correct orientation of the parts and the required patch at the tip of the handle is included as well.Alternatively, check out the settings in the table below:Nozzle Size:0.4mmLayer Height:0.2mmFilament Materials:PLA, PETG or...

You'll need 4 x 5mm M3 machine screws to attach the mount to the block and 3 x 20mm M3 machine screws (2 if using the slide-on nozzle) with nuts to mount the nozzle and fan. I've also used nylon washers, but those are optional. If using the slide-on...

It's lightweight, thin and works with only one USB cable. Parts list: PLA M3 steel hexagon socket screws to attach the PLA pieces to the aluminium tubes two 1-meter-long aluminium hollow tubes, 8mm diameter, 1mm thick, to cut small rods for the...

I am using an Schego WS3 aquarium pump that provides 0.3 Bar (compared to cheap aliexpress ones with 0.15 - 0.2 Bar) and also about 5.8L/min (which actually is much more than needed at this pressure). The result is about 1L/min air flow through...

The double wall of the lampshade creates spectacular moving moirés and unusual shadows - this is best shown in the video: The plafond can be printed in two versions - as a thin veil (LiquidCuprum_lamp_1) and with wider straw-like bars...

2. Pop in the keyswitches. Make sure they are in the right orientation! 3. Follow the wiring diagram (at the end of the photo gallery) to solder the resistors and wires across the keyswitches. 4. Solder the wires to the Arduino Micro. 5. If doing...

Edit 2: The tab is now properly positioned on the trapezoid, as long as it's not twisted to the side. There are parameters to adjust its position in that case. The trapezoid can be leaned to one side, and the tab should move with it. Edit 3: If a...

You also need, but could likely have already done since there's some good advice being shared on Thingiverse: The best 2 x motor drivers available, such as an ESC controller Also two brushless motors suitable which would include any additional...

2. The second type handles the more unusual case where *one of the bolts is in the middle of the bracket slot*. Typically used when joining two alu pieces where one of the alu profiles is across the join instead of pointing into it, as often...

This reduces the risk of getting glue residue on the front.Step 1Lay the outlines on a flat surface and glue the following parts to them:FaceBodyEarsTailStep 2 Glue the clock face to the outlines(LED version only)Attach the LED strip to the...

2. The Y belt clamp: This is shaped for my particular carriage but feel free to modify it to suit your own setup. 3. The Y end stop mount: This fits directly in front of the Y axis motor and I've had no problems using this setup but double check your...

The "tunnels" to make real wires run under the pads and finger pieces will need sanding/filing to make your specific wires work The tunnels are around 1mm in diameter at the outer edges, but widen out to a bit over 3mm wide further into the model I...

Optional you can also use just 2.85 3D-printing filament like I did in my vase project. But you have to bend it before inserting it into the channels. There is a cylindric hole inside the pumpkin to store batteries.</p><p>Only basic soldering skills...

You may also be interested in my Dust Collection Port (v1.0) for DIY Router Table - designed for 2.5" hose from Vacmaster shop vacFeatherboard for woodworking, no supports needed, with M5 & M6 options for knobs & track slides - plus ¼" bolt option...

PARTS REQUIRED: 0.96inch display(1pcs):...

It has 2 durable springs (if printed with PETG). These two springs allow the springer to snap back to a rest state regardless of which way it is spun.</p><p>The springer was inspired by fidget spinners and <a...

To ensure rigidity, aim for at least 1mm walls (3 perimeters at 0.44mm line width, 2 perimeters at 0.7mm line width).To make the tubes, cut the Bristol board into two sections, with one being roughly 36x12 inches &nbsp;(300mm long) and the other...

Printing/Post Processing: - Small nodes with short shaft have been printed successfully at 0.2, 0.16, and 0.12mm layer height with PLA and 30% fill. Print with the shaft facing up and turn off supports. - Large nodes with short shaft have been...

... Exact nozzle to probe offsets are in the Post Printing instructions. If you are considering upgrading your I3 printer with a BigtreeTech SKR mainboard, as I have, then check out this mainboard case I designed for my Wanhao I3 with BTT SKR 2:

Test this by printing a slice of the support with 2 magnets and testing it in isolation. I greatly recommend against increasing strength and instead to add the silicone rubber strips (or some other grippy material).When tensioned, the silicone rubber...

Update 2 (2015-06-02): Added Wiring.pdf as a better display of how to hook this thing up. IMPORTANT NOTE: This hack is intended to be used with the Ultimaker Original power supply and electronics platform. Don't use it with anything else than that...

Drill all holes with a 2.5mm drill bit. Tap the hole in the center of the bed with a 3mm tap and put a screw in with lock tite and grind flush. The Bed -------- I've found that nothing sticks to this stupid thing, including Elmer's purple, hair...

... ...:) My fav PLA on Amazon Italy: Tianse PLA Sunlu PLA+ JAYO PLA+ My fav Resin on Amazon Italy: Elegoo ABS Anycubic NOVA3D Rapid Resin Print Settings Printer: Alfawise U30 Rafts: No Supports: No Resolution: 0.2 Infill: 15% Category: Toys & Games