breakout type s 3d models

PCB cooling duct for 40mm fan,keep those ramps cool,heat sinks are technically enough but for electronics that run all the time or run hot when in use it's best and never a bad thing to have more cooling,the one I included has both the duct and fan...

What's new: Reinforcement of the strap attachments (a little too fragile on version 1) and the structure of the case. improvement of the design. flatter (less clutter). addition of a space compatible with a thick filter or folded accordion...

It's a bit thicker (+3mm) to allow you to screw the steel plate on to the Probe Distancer. Use short screws so they don't touch your 4010 fan. PTFE tube length to cut: total 34mm (have tube sticking 6mm out of the Groove Mount Adapter) Never used...

I really liked the idea behind the cable chain maded by NG_Designs ; https://www.thingiverse.com/thing:3769941 but i decided to redesign it because it's really hard and long to print. NOTE: for safety reasons i suggest u to set up the MAX Z...

This highly specialized Cult Furniture Elgin Stool is an ideal blend of sophistication, modernity, quality construction and user-centric features designed specifically for today's consumer. Here are the specific features incorporated into Cult...

Tripple check it's flat and flush with the end. Then drill all 3 holes using a 5mm drill bit. Go slow so you do not split the Carbon Fiber. Depending on what material you use to print the template, keep the drill as straight as possible so you do...

Mount the trigger on the left body with the screw and nut to hold it's position, then fit the spring and spring retention plate. Temp fit the micro switch and check that it depresses when pulling the trigger. Adjust the micro switch position as...

I will tidy those up a little eventually. Here's a new approach to attaching the E3D Hemera to the Anycubic i3 Mega. I decided to rotate the Hemera extruder 45° towards the display in order to not lose so much build volume in the X direction. Also...

That's exactly what a 3D printer is for. The holder is mounted on the frame with Tesa Powerstrips to prevent it from moving, and the final mounting is done with black cable ties (2 pieces). You can also use other adhesives, but you may want to...

Modified Makkuro's customizable text box to have thinner top layer on the lid so LEDs inside can glow through better. I added descriptions to the settings, along with recommendations. I tested this on a 300mm x 300mm build plate, and in some...

The print speed for me was 70 mm / s (I was a little reinsured, on layers above 15-20 you can speed up the print). As the speed increases, the plastic becomes matte, if you want to get a glossy shine, you should not increase it too much (and I...

für die Knöpfe S/W, 1x für die Mitte in dem Innenteil u. 5 St. für die Negativform) und 4 x Magnete d= 15mm h= 3mm (Innenteil) benötigt - das waren die Magneten die ich noch in der Bastelkiste hatte... Ok. es gibt noch zwei andere Formen von...

If it's too tight just select a smaller diameter from the Customiser and print again. The adapter is purposely about 2mm longer on the inner surface than necessary. This is so you can mount the adapter on the mandrel and face the surface down so...

I recommend going with [Wera's "Take it easy"](https://www-de.wera.de/en/great-tools/take-it-easy/) color scheme. ## Spacers To make it easy to remove/insert screwdrivers into a holder you may want to leave some space between them. You can do...

As a FYI: I noticed that the original design's gear2 design had a slightly off-centered Gear2 shaft (the one that fits a 14mm socket). It is useable as it is but the shaft offset causes a slight wobble so I remixed gear2 to align the shaft on...

My printer was built according to nophead's GitHub files, modified due to part availability. When printing PLA, everything is fine, but when starting with ABS or other materials, a very slight smell of smoke can ruin the print. After scouring...

Just like a helium balloon in the earth's primarily nitrogen atmosphere. Still there are limitations in the amount of lift that can be generated due to the low pressure, but some of this will be countered by the lower gravity (Revision, no it will...

There's also space in the flamethrowers to add extra LEDs. I have some flame effect orange ones and printed transparent flame models but didn't add them in the end. The inside of the arc reactor, switch on the left arm and flames if you use them...

60mm/s, 0.2 mm layer height. no additional calibration. Due to 1:5 reduction extruder is capable of high extrusion rates (only simple extrusion test was performed) ...

It's a bit thicker (+1mm) to allow you to screw the steel plate on to the Probe Distancer. Use short screws so they don't touch your 4010 fan. * PTFE tube length to cut: total 34mm (have tube sticking 6mm out of the Groove Mount Adapter) Never...

(So that's six total magnets or 10 total magnets) PRINT THESE FILES: If you want single color prints: Case Threaded.stl if you want threaded nozzle holder, OR: Case NoThread.stl if you do not want threaded nozzle holder. Cover.stl If you...

There are three different ones, two that have a flat inner face for going around a flex hose if it's collapsed, and the second for command 2.5" PVC pipe. The third one has a inner beveled face for going into the groove of a flex hose when expanded. ...

This accessory is an add-on to V1 Engineering's MPCNC Primo version CNC machine and provides a mount and dust collection attachment for the DeWalt 660 Router. See <a...

It's thicker and stronger. I printed this latest in PETG since field testing showed the PLA version had issued in the sun. Updated all photos. UPDATED(2021/4/12): New version better tuned to print well\cleaner. Changed fiber pin link below to...

2) After loading in new application called Rhino go back in to Panels > Material Editor You may have found by navigating that it’s all set ready, now select from left menu material that is using some texture of any given one (texture applied), then...

Textures can now be located next to this model's directory. Alternatively use any trial software, where .skp files open automatically within minutes once C4D is started for importing from. Using native export file path options for accessing your...

You could use washers but that's wasting like... 40 cents. Just print it solid and your good. ####BINDING TOP CLIP FOR STRONG PRINT, ROTATE OBJECT 45* SO THE CORNER IS FLUSH. This is made to be supportless. Use high infill (30-50% gyroid). ...

See als my other Iso 7010 collections: Emergency Symbol collection: https://www.thingiverse.com/thing:4830734 Fire Symbol collection: https://www.thingiverse.com/thing:4830768 Warning Symbol collection: https://www.thingiverse.com/thing:4834030...

You should be able to take off the entire driver.Step 5: Solder the new wire to the jack's PCBRemember the colors used! Step 6: Thread the wire through the left body Step 7: Screw the M3x10mm screws through the driver plateScrew the screw completely...

Specifically, Traxxas’s TRX6 wheelbase will be a direct match. i.e. 324mm from front to middle axle, and 130mm from middle axle to rear axle. The Expedition cab mounts designed for the TRX6 are also included to make mounting easier. You will still...