cad modeling practice

I needed a quicker and simpler solution to perform these tasks so I could focus on slicing and printing actual models. What is more basic than some good old push-buttons?</p><p>Feel free to remix it as you wish. It would be nice if you upload the...

OK, this isn't a model but rather a gcode script to facilitate automated cold pulls to clear out your nozzle. I use it all the time on my Ender 3 and thought others might get some good use from it as well. **What is a cold pull?** A cold pull is...

... 3D model created using SketchUp Make (free software). I also tried 45 degrees, but the fan's thickness made it touch the desk surface below, so it had to be skooted up to the high end of the stand... thus the cooling effect would be diminished.

A great way to combat this on any print with sharp corners is to add “Mouse Ears”.• Add these in PrusaSlicer by right clicking on the model in the list on the right of the screen, hover over “Add Part” and select “Add Cylinder”• With the cylinder...

It has been almost three months in the making, and several bits are an additional 100–200 sketches beyond the base model, which means there is a ton of Mf-detail, I probably overdid it. My goal was to create something special for kitbashing,...

In addition, in case you want to remix you would potentially only have to adapt the holder model.The bottom of the holder has a cavity that exactly fits a specific lightning cable found on Amazon with angled connectors to reduce the space it...

It's just a model I whipped up, and sliced it with a bunch of retraction changes. Then went back and spliced all the g-codes together. Base Cura profiles I use: layer height - 0.2mm Optimize wall print order (do not retract before outer wall), print...

The assembly is tailored for the older model C8, CeleStar Deluxe with the double fork equatorial mount and an under-rail for weights, dating back to c1998. Materials List • The three C8 Camera Mount Assembly prints o C8 Front Bracket o ...

Instructions First make sure the nozzle diameter and layer height match your slicer's settings, as by default the model is exactly 2 nozzle-diameters thick in each slice so as to avoid generating any fill paths (which would show up when lit). Also,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

My intention is to provide a set of variant files for the Mutant on different Prusa models (MK2.5S and MK3.5S+ are the current targets). To get the firmware to recognize the changes for a wider X gantry, you will need to compile your own Prusa...

Every detail has been painstakingly worked by our artists, who have also designed the tiles to ensure repetition of patterns are minimized as much as possible on each miniature/model in the INSTADUNGEON™ series. LET EACH TILE'S PHYSICALITY IMPACT...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

There is not a real place for the buttons, but hotglue eliminates hours of 3d modelling, at least for me, and works well enough. This is a WIP so take as it is. For the wiring it's quite straightforward, take the 2 external potentiometer pins an...

For manufacturer theme decoration walls, can be downloaded here: https://cults3d.com/en/3d-model/various/1-64-generic-showroom-brand-names-decoration-c54d91474b2b2c374a87 The cars I used in the photos are: - Porsche 911 (992) Carrera S (Mini GT) -...

For more details, visit http://www.thingiverse.com/thing:47032 [^] (v.1) naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio naio...

Some of the models are difficult to hand-launched and should be tested with a 1/16" rubber band instead. A slight elevator-up reflex is required for flight. This is accomplished by latching the elevons up on the relex tabs on the aft end of the...

I made it in the same scale as that model (1:1.2168x1017, about 8cm long) so you can use the same display stand (https://svs.gsfc.nasa.gov/vis/a010000/a011500/a011568/model_stand_80mm.pdf); and in another two scales, three and six times bigger...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

I still have not got this model right, the results are not really satisfactory. Maybe I don't have the ball geometry figured correctly or the latitudes measured properly. Sometimes the slicing does not join the detent teeth skirt properly to the...

More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD on your own computer to process the code to create your own customized models. See DrLex's...

the 1.3 inch screen you may be able to find different options with the same measurements, or else you will need to modify the model. everything else offers a little more wiggle room. 5. ice tower cpu cooler (depth on this ended up being close,...

**5** Shift Knob (Optional) I have NOT tested this as I opted to use a real shift knob, but the model is there if you really need it. I would suggest printing it upside down. **6** Pivot Pin & Pivot Cap (Optional) These are only required if you opt...

instead other models of TMCxxx , No solder iron necessary, you just have to rotate the connectors receptacles on the motherboard with a simple leatherman tool.like on this video Be care, some of the latest motherboard doesn't have support under the...

(custom_bottom_outer_edge_chamfer_radius = .6) - Type or kind of phone: set model type number three (phone_model = 3) - Turn on a flag or no use to make image stencil and so it be applied all around and that we turn this choice option on always by...

This model IS NOT HOLLOW, but is mild steel. you'll want a really long carbide bit. It drills pretty easily though, and will not affect structure. . Drill a similar sized hole on the back side of the frame. Screw the slipring adaptor into the center...

I still have not got this model right, the results are not really satisfactory. Maybe I don't have the ball geometry figured correctly or the latitudes measured properly. Sometimes the slicing does not join the detent teeth skirt properly to the...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...