cam modeling

The best way to goRA30 - a slight twist, a gentle rotationRA70 - a steep rotation, will probably end up shredded by any launchFor all of the challenge outcomes, we used the V1-SO65-H100-RA00 model.Further refinementAfter the competition, I refined...

Why the filter? Filter design will not interfere with internal spool or the moving bed!Apart from significantly cleaning the air inside the printer chamber the filter will also circulate the hot air in the chamber and will help it heat up faster...

I'm always more than happy to modify the models and post new revisions if anybody runs into snags or has an idea of ways to improve the design. UPDATE 3: Finally finished filling out a set of 3 modular trays, and added a picture of them here. I...

The Original Minumus has a phenomenal array of ducts and blower variations, and if you want to print a lot hotter (Spider, etc) that is what I would use.You can find that here:...

The engraving should fit perfectly into the groves of the Box part.Assign the colors to the objects (see picture below).Add pause print as mentioned above (2-part version).Slice the model. You are now ready to print.Printing:Load the Filament for the...

The instructions below can be followed for assembly. Print instructionsUPDATE: I've added a 3 piece version of this model for people that may be struggling with the 1 piece print tolerances. The body can be printed in 2 pieces and the slider as a 3rd...

... -- Align THE feet with the locating pegs on the baseplate, it will only use two and the other two will go behind the heels to stabilize the model. It should only attach to the baseplate in one way, so that its back is to the edge nearest the pegs.

It is highly recommended that you use these new models instead of the old ones if you have already downloaded them. ATTENTION: as of 7/3/2023, all files have been once again replaced with a structurally reinforced and improved V3 version that aims to...

This project is a low cost option for adding significant upper gantry and Z axis stiffness to the Taz frame for all model Taz printers. it uses 3 20mm surplus Taz extrusion (3x 500mm or 1x 510mm and 2x500mm for a Taz 6 specifically) some 55mm long M5...

;)Way more up-to-date models and info over at my other listing on Printables Features Modulor Stackable Standardized Efficient Material Usage Scalable Modifiable There were many considerations to getting this system dialed in. Of course, the...

You can also print one of mine, they should be frictionless enough PRINTINGPLA or other materials, no requirements. You can visualize the full assembled model and divide it into pieces in the slicer or just print what follows:Core 1-2Ring 1-26 x...

I think following that advice would make your chance of having a leak even lower, but the increase in print time for such a large model would be significant.Valve FloatThis floating block is what opens and closes the drain. It needs to be watertight...

External links: Buy Kit at Rat Rig Step by step Build Manual Facebook Rat Rig 3D Printer Community Project Documentation (BOM, Build Guide, Assembly Videos, STL's and other CAD Files) Full Fusion 360 CAD Model - Single Extruder Setup Full Fusion 360...

I also intend to include additional models that will be compatible with these in the future, so follow me to stay up to date.Warning: Not all configurations of this have been tested. It is advised that you ensure that your design is stable before...

And if you want to glue print the top part 3 for gluing instead of the normal top part 3.-a little spring (you can find this in the most ballpoints)  Please follow the instruction below InstructionPrint all the parts with your standart...

Solid form (Bullet Lock, Solid Lock, Air Lock, Fluid Lock, Gas Lock) lock models, what you need to know for solid liquid gas binary transactions. . Washing machine, dishwasher, dust broom, crumb broom, soot broom, air pump, water pump, vacuum...

If you have large hands the bits will probably poke your hand a bit. Also added small holes under the magnets on all models (except round one) so they are easy to knock out if they get glued at an angle, or break. You will need something that's...

This is very much a project where touch is just as important as the look. If you have a Prusa MMU setup a filament change 1/2 the height of the model. JOY looks great as a two color print!</p> <p>Bigger Joys</p> <p>Want bigger Joys? Pocket Joy is not...

This is to facilitate the use of my new clicky adapters, which you can find here.&nbsp;The Macro-Jack, big brother to my previous version the Micro-Jack, and with even more fidgety functionality! My idea was to create a fidget toy that sort of acted...

This specific measurement with the eyes was changed after overlaying our sketch of the ghost with the printed ghost model. We could see that the eyes were a bit too far apart, so we placed them slightly closer to each other. Initially, the eyes were...

(Dynamic input) Short cut keys:- Ø Ctrl+A : select all Ø Ctrl+B : Snap on/off Ø Ctrl+C : Copy objects to clipboard Ø Ctrl+D : Dynamic UCS (DUCS) on/off Ø Ctrl+E : To change isoplane in isometric Ø Ctrl+F : Osnap on/off Ø Ctrl+G : Grid on/off Ø Ctrl+H...

I just did it with this site )On the page, the image is uploaded in the first step via "images" choose file.then go to "settings" -&gt; "Model Settings" and apply the settings from the following image.then do the same with "settings" -&gt; "Image...

 I used Polymaker Matte Army Blue and Overture Matte Grey.Photosensor cover, LED diffusor, and Arduino board are printed with clear PETG.Several models include a one layer solid over the begining of holes printed down for clean circles without...

version 2 of my Liberator Teleport bracelet from the old BBC show Blake's 7 Print instructionsBlake's 7 Liberator Teleport Bracelet After posting the Liberator Wand files recently I was asked to model up the Teleport Bracelet from the show.   As I...

KS1/Resin models stored separately Supports partial sleeving with a focus on shuffled cards (loot, initiative) + the character/combatant cards. <em>In test - may support full sleeving</em></li> <li><strong>Lids</strong> to reduce chance of spilling...

You can add some graphite powder lubricant in between the roller and the plastic bearing for better rolling.UPDATE (30/09/2018)Added the source file for the brace (.step).UPDATE (17/11/2018)Added stand.UPDATE (20/03/2019)Added source files for all...

The two Hyperdyne Model 351 Medium Laser are very durable, but still are occasionally damaged in hand-to-hand combat. The sensitive lenses and frame alignments can be disturbed by the impacts common in 'Mech fighting. The two rear-facing small...

You need to tune your machine to make sure it outputs a print accurately, For me it worked best setting it square to the build plate, (no raft no supports strait on the plate) to help fight any warping, I know conventional wisdom tells you to “tilt...

If you feel resistance check the coils on the cylinders internals for print flaws, stringing, or even shifted layers.Note: On a freshly assembled cylinder you might feel slight resistance but this should improve over time as resistant parts wear from...

Check this out: https://www.printables.com/de/model/208896-mini-caliperHow to printSame print settings as for the magic bookshelf baseSame Filament you used for the magic bookshelf base (I used PETG)Brim: 5mmEnable supportsPlace it on its side as...