cockatoo animated 3d models

It looks like you've got a table with some planetary models and their corresponding scales. Here's the cleaned-up HTML for it: ```html <table> <tr> <td><a href="https://www.thingiverse.com/thing:3720464">Earth</a></td> <td...

It should be possible to customise the model by changing a global variables that represent the battery dimension and straps width- holes for the LED indicators- reducing the number of screws- creating the cases for wider range of IMUsPlease let me...

I have printed all of the parts and assembled a model which is shown. The "Dome" cover will fit over the Base Plate, and in turn a 1/2" piece of sprinkler pipe will fit over the tabs in the center of the Base Plate. The Mic Holder will fit over a Gen...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

A .3mf file is available along with the STL models.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it works best to drill a first hole and then insert a screw into that...

Each time I found that the support material came away beautifully… right up until I printed the final model. A tiny piece of the design broke off with the support (see pictures). Thankfully It's not an essential part. It's only there to keep the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_pattern_thickness = .8 custom_back_extra_port_y_size = 30 custom_back_camera_corner_resolution = 8 custom_top_port_x_position = -10...

The shade is 196mm high - be sure it fits your printer's build volume. Print it in white or even translucent PLA. The model has been adjusted in Meshmixer to be solid. You need to print this in <strong>Spiral Vase Mode</strong>! This will print the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

Update to v9: Put the K25 spring into the model, looks like it fits fine with about 2 whole whopping inches of precompression. Rounded off the corners on the PR guide (which isn't much of a spring spacer anymore) to help the spring go smoothly. Now...

After studying what was available, I started modeling my own. The problem was that most of the projects were on console tables, but our table is held on two rails, one on each side. Initially, the project was implemented on a seven-string polispast,...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! Update 1: My Start and End G-codes in Cura working well with this firmware: ...

... you'd like to copy it into your workspace and mess with it. [Buy me a coffee :)](https://www.buymeacoffee.com/jcolega) - [Printables](https://www.printables.com/model/152611-lego-vehicle-wall-hangers) - [Thangs](https://social.thangs.com/m/65559)

The model formed in our minds is based on what we see, and the brain completes the rest, including hidden features. So, I set off to design the object using Fusion360 and test it. I created several versions of the lock inside the object, but this one...

Tree Supports and possibly Outer Brim required for some STLs NOTE: The STL Models may display some artifacts from revision builds, but will not appear in Print RECOMMEND: Allow pieces to cool to room temperature on printers Heatbed before removing to...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

1x M6 square nut - model allows for 5mm thick, 10mm square 1x M6 set screw (10mm length recommended) Important: while printing you MUST put a pause at the layer just before the nut is covered up. Look for the small "box" cavity in-line with the...

Modeled after a 1915 candlestick phone, early versions had no dial because you just lifted the earpiece and clicked the lever a few times to get the operator's attention and told her the number or person you wanted to speak to. This is a fairly good...

After filing and sanding the bonding surface flat and smooth, and clamping the holders to the shelf with masking tape for a week, these pipette holders have stayed firmly in place for two months with no peeling or drooping.\n\nRedesigned the holders...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

I made a slight modification to the model by changing the profile of the USB input so the bridge was less than 5mm (was almost 10mm) and changed the way the board mounts so the top has all socket heads and no washers (just an aesthetic thing). <a...

Initially I modelled the candle I wanted, then using boolean operations subtracted it from a cube, and split the cube in half. ...Then I added the pins and matching holes just to help align the boxes and hold them together a bit by padding and pocketing...

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

[Medium Sized Model - 25mm Base] [Presupported in 32mm and 75mm scale]   One of the few Colossals on Tharador not to be born in the bitter Frozen Wastes of Oldavor. Harmara is also one of the few hemomancers to exist out the bounds of Oldavor, the...

To do this I went to https://3dp.rocks/lithophane/ sized it in model settings, and set it to Positive under image settings. I kept it flat since it will be used as the back of the bookstand. But while it's not in use it can also be used as a cool...

The Doors Pack includes 47 models (each in .stl and .obj format, making for 94 files) and adds a treasure well of different doors to make your dungeon unique. It is also the first expansion pack I got ready to publish. Some of the doors come in...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...