command conquer 3d models

This model is for a “streetlight-style” wired garden/pathway light. Brighten up your garden path with lights, without spending a fortune on MoonRays or similar products where a single lamp can cost up to $20! In bulk I can make these for about $3-5 a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

They can easily be swapped around.PrintingMain HandleIn general you should use the flattest side of the model on the print bed. Your settings shouldn't be adjusted too much, the standard high quality settings of your printer (or whatever tuning works...

If you print this, you won't need to print the motor_plate-beta10.stl as it directly replaces it.     These parts are the latest as of 28 April 2022, if the VORON team changes the motor_plate drastically it will no longer work.     For those that...

The Doors Pack includes 47 models (each in .stl and .obj format, making for 94 files) and adds a treasure well of different doors to make your dungeon unique. It is also the first expansion pack I got ready to publish. Some of the doors come in...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Finally you should set up channel mixing for tracked models in your transmitter. I added 2 photos of my mixer setup, but this video here explains it very well: https://tinyurl.com/bdns4pj5 It took me half an hour of trial&error negating channels...

This is a well known test model with many remixes.However, I have not seen anyone with automatic temp range.Existing temp tower is “semi-automatic”, they set temperature to preset levels with custom g-code in “before layer change”This print set...

Buildings 1) Human Living Space -This is the repurposed spaceship used to fly to Mars -It is already radiation-proof out of necessity from the trip to Mars -Already equipped with heaters from space travel -Much of fuselage is repurposed into a...

When properly positioned, the latches are ready to engage by sliding the wiring cover all the way to the right.\r\n\r\n###Parts List:\r\nAll links at Amazon:\r\n\r\nQty 2 required: 8X2mm...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

# Overview A mini, working model of an escalator. Turns via a knob on the right side. Motorized version available at https://www.thingiverse.com/thing:5375662. Latest Fusion file: https://a360.co/3JnNqV1 Video: https://youtu.be/95yZLk6EauM ...

- Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

I have left the original design files as well to preserve version control. Design File Included: .f3d, .ipt, step, .skp, and .obj files. Follow The Makers Workbench...

Link below --- Build history Years ago, duno, I made the bigger first case desgin, roughly modeled after the original. 2021 -the 2.nd design of a modified, more streamlined versatile case was made. -modified the pcb layout -new pcb was made...

When I figure out a way to secure both together and close the gap, I'll update this model. If you wish to have a display base tweaked to fit to a different car from a different brand, please send me these dimension for the display base holes:...

Tools Hex wrench 2mm and Mmm...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Here you find better resolution for the pictures: https://www.printables.com/de/model/501107-led-rgb-matrix-ws2812b-esp32-wled-32x32-round-squa https://www.youtube.com/watch?v=5lFdzL06OOs On Youtube there are lots of tutorials to build a 32x32...

IMPORTANT INFO REGARDING ARRMA 6s REAR HUBS: There are basically two versions of the Arrma 6s rear hub between all the 6s models (36mm wide and 45mm wide). <b>The recommended version are the hub parts used in the 6s Kraton/Notorious/Outcast which...

Use for reference) Hardware needed: Two 5015 blowers (get the correct voltage for your printer model). I recommend Sunon maglev. Europe: https://www.tme.eu/gb/details/mf50151vx-a99/dc12v-fans/sunon/mf50151vx-b00u-a99/. A suitable connector to the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

And yes, I'm already working on another version to fit the standard width tank; it shouldn't be too difficult to scale it down from the XL model. I've also come up with an alternative design - a curved blade that's just as effective but looks much...

What's IncludedThe entire Anvil Digital Forge Patreon release for January 2024, including; Multi-Shell Options:A number of STLs are labled with "(Multi Shell)" - these files can be imported into Blender (reccomended), or Meshmixer, or various other...

There is a tight-thread version of all the models for those wanting a tighter fit or using a resin printer. Caps Flat Cap Flat Cap with GB Logo Cap with 3/4" Loom Stub Cap with 3/4" Loom Stub and Circuit Passthrough Cap with GX-20 Geometry Cap with...

Research I found two suitable models on Thingiverse which I thought could be easily enough modified: Tweezers for SMD by Ruslan_Kulibin SMD Test clamp by Tom20170 which I both printed yesterday. They are both quite nice designs, I especially like...

My original plan was to also model a strap clip for the bottom of the mount, but I found that it was unnecessary, as the entire thing can be attached directly to the head strap and head pad with a velcro strap. I used a couple of long velcro cable...

Merry Christmas! You will need to print: 4 ea Whirligig blades 3 ea Eccentric cams 2 ea Crossbars 2 Reindeer 2 ea Base Couplers 1 ea all other parts There is a cutaway view in the thing files called cutaway view.pdf showing how the model goes...