cr 10s max 3d models

This is a remix of CarstenD for my CR-10 Max with Micro Swiss hotend and direct drive. I decided to replace my broken fan with a 5015 more powerful one. (Pay attention, that the stock fan4020 has very weak soldering and once a cable felt off...

This is a coupler reinforcement that gets mounted onto the extruder of a CR-10S Pro or CR-10 MAX. ...The purpose of this part is to prevent the bowden or capricorn tube from slipping out of the coupler.

### Other Printers I am assuming it will also work on the CR-10S Pro, Ender 5 Pro, CR-X and CR-10 Max since, from what I can tell, they all use the same screen and shell config. I included the Fusion 360 files for this. This is my first self...

If you have a TFT70 you already bought and want to enjoy the awesome size of the TFT70 screen, hopefully this help you out :) ### Other Printers I am assuming it will also work on the CR-10S Pro, Ender 5 Pro, CR-X and CR-10 Max since, from what I...

There are already a lot of z height blocks around but I was looking for maximum precision while haven also a maximum ease of use. I found some designs leveling x to y rails which would give maximum precision, so I went for this concept. To get the...

<p>There are already a lot of z height blocks around but I was looking for maximum precision while haven also a maximum ease of use.</p> <p>I found some designs leveling x to y rails which would give maximum precision, so I went for this concept. ...To...

There are already a lot of z height blocks around but I was looking for maximum precision while haven also a maximum ease of use. I found some designs leveling x to y rails which would give maximum precision, so I went for this concept. To get the...

An guided brace which can help the filament move into the hotend more smoothly... I noticed that there was a noticeable bend where the bowden tubing and the hotend meet. In the long run through wear the bend might create additional friction which...

A simple mounting system for adding an E3D Hemera to either a Creality CR-10S Pro or CR-10 Max. The main printed part simply acts as a washer/spacer for the Hemera, with the aim of max rigidity. It also serves as a template for drilling two holes in...

A simple mounting system for adding an E3D Hemera to either a Creality CR-10S Pro or CR-10 Max. The main printed part simply acts as a washer/spacer for the Hemera, with the aim of max rigidity. It also serves as a template for drilling two holes in...

A simple mounting system for adding an E3D Hemera to either a Creality CR-10S Pro or CR-10 Max. The main printed part simply acts as a washer/spacer for the Hemera, with the aim of max rigidity. It also serves as a template for drilling two holes in...

If you cant get the belt length this setup should also work for the CR-10s Pro with belts from approx 900mm to 1200mm Shopping list: - 2x GT2 20T B8 W6 pulley (6mm wide, 20 teeth, bore 8, with grub screw) - 2x GT2 20T B5 W6 idler pulley no teeth (6mm...

If you cant get the belt length this setup should also work for the CR-10s Pro with belts from approx 900mm to 1200mm Shopping list: - 2x GT2 20T B8 W6 pulley (6mm wide, 20 teeth, bore 8, with grub screw) - 2x GT2 20T B5 W6 idler pulley no teeth (6mm...

Best of both worlds: Touch screen display + emulated 12864. I designed this in anticipation of upgrading my machine to a 32-bit board (SKR Pro) and TFT35 V3.0. Uses the concept and mount plate from Nitec0re's design, but pretty much a redesign from...

This is a Snap-on Filament feeder to cut down on the amount of filament dust. Recommend printing size at 100%-102% depending on your printer's tolerance and accuracy. Also recommend using a minor amount of bed support. Lastly, depending on your...

Printable mount, fan duct,  BLTouch and EZABL mount for the CR-10S Pro and CR-10 Max and the E3D Hemera. ...The EZABL mount is based off measurements and still needs to be tested

... find one anywhere. ... I actually bought one and have updated it. My fin to fin spacing is off a hair, but everything else is good. https://store.micro-swiss.com/collections/all-metal-hotend-kits/products/all-metal-hotend-kit-for-cr-10-pro M2591-04

Fan shroud for installing the Micro Swiss Direct Drive Extruder on the Creality CR-10S Pro V2 or Creality CR-10 Max. The CR-10 Extruder/Hotend package comes with the 4 finned cooling block. The CR-10S Pro/CR-10 Max All-Metal hotend comes with the 5...

Mixed the two togheter. ...I liked the ValleyBot LED view and screw access better plus space for a small piece of PFTE for added smoothness feeding into the sensor chamber and the versatility of the roller from micromike's design ;)

Print in ABS if possible

Mixed the two togheter. ...I liked the ValleyBot LED view and screw access better plus space for a small piece of PFTE for added smoothness feeding into the sensor chamber and the versatility of the roller from micromike's design ;)

This is meant to stop the friction at the filament runout sensor of the CR-10S Pro model printers. This should stop the buildup of the filament grinding against the metal housing. Use a standard printer rail roller bearing to complete. Depending on...

(The assembly of the plate should be explained by the reseller)Also use some additional M3 bolts to mount the washer cable strain relief arm to the plate.Use M3 bolts to mount the cable mount to the the washer cable strain relief armUse some self...

For the CR-10 Max I did my own kit (https://www.printables.com/model/229071-cr-10s-pro-cr-10-max-z-sync-various-belt-length-po) which allows you to use belt which different length (approx. 1200mm to 1600mm). This Kit only works with the “on top of...

Clip for the cr-6 max webcam mount to work with the cr-10s

Cr-10s 4015 Fan stock hotend

This can be used when designing a part that should be clipped into the CR-10S / CR-10 rails

Filament guide before filament sensor cr-10s old one

Filament Idler for the CR 10S Pro printer.

Uploaded this to help others design accessories for the CR-10S PRO hot end