cr touch z offset too high 3d models

Synchronize your CR-10S Pro Z Axis steppers without sacrificing print capacity or risking damage to your printer! **Edit 3/3/19:** By request, I've added V2_Beta (untested at this point) to enable socket head cap screws for mounting the stepper...

The CR-10S Pro struggles even more than the CR-10 series when it comes to Z motors going out of sync on power off. This is due to the same design as the one used by hoegee, but it works perfectly for the Pro as well. In my opinion, this is a...

Improve layer quality, eliminate wobbling of Z-axis motors.

Improve layer quality, eliminate wobbling of Z-axis motors.

This is a remix for the CR-10 Max to work with a GT2 6mm,1140mm belt. ...The structure is enforced and holes are increased.

... can be easily modified to accommodate longer belts if needed. Essential hardware components include: - Two high-quality 688 bearings - Two sturdy 3mm T-nuts - Two strong 3mm screws - One reliable GT2 timing belt, measuring larger than 760mm

When printing, use at least three shells for the bearing block as lateral force on this part is high. Infill should be at least 25% and up to 33% for strong parts. PETG works best at a height of 0.2. Check out the ordinal design at...

I required an additional extension from the frame to fit in my dual Z motor alongside a PSU shroud that houses a front-loading AC power supply.

The original BL touch bracket didn't fit my CR touch due to the cables. This version is 1mm thicker than the original and fits the CR touch well. ...The mounting holes are the same so it might still fit the BL touch as well.

To implement this solution, you will need: (1) Dual Z Idler Bracket (attached file) (2) Idlers (6mm height, 5mm bore). I used these: https://www.amazon.com/gp/product/B07CCMQ8T7/ref=oh_aui_detailpage_o03_s01?ie=UTF8&psc=1 (2) GT2 Timing Pulleys. I...

To install the Z damper: 1x printed detail from here: 2x short M3 bolts 2x M4 bolts (like the original Z motor holder screws, but shorter and with t-nuts) - I don't recommend messing with original bolts in case something goes wrong. You can print...

Modeled with very high accuracy; however, depending on your printer and settings used, you may have to scale it up or down a bit for a tight fit. Dimensions: 60mm x 25mm This will work well with Z-Axis Bearing Stabilizer by benawhite at...

Satsana fan duct modified to fit the Z shaped creality direct drive extruder mount, The creality Spider hotend, and has a built in mount for the CR-Touch. I included the .3MF File to be opened directly into cura if you don't want to mess with adding...

I added height to this knob to clear the top of the frame braces I just printed and installed on my CR-10 https://www.thingiverse.com/thing:2123233

Mine clips in place on the base and onto the z-sensor bracket and is held in place by the drawer - but if you print and it's too loose - you could use some blue-tack or double-sided tape to hold the two pieces together - or just increase your...

This design is tailored specifically for the Taz 6, paired with a Printed Solid enclosure and a dual extruder V3 setup. ...It cleverly adjusts the Z-axis stop downward, ensuring that the top of the extruder safely clears the enclosure's top edge.

This z-axis sensor mount substitutes the standard mount, but its holes for mounting micro switches are 1mm lower, resulting in the print head falling 1mm short. The G-code used was from a PLA+ 210-degree print on my CR10S. I've included the Fusion...

It's incredibly challenging getting two linear rails perfectly aligned for a Z-axis conversion. Most conversions only work because they utilize low-cost rails that have enough play to compensate for misalignment. As a result, this conversion focuses...

Do modulu byli přidané snímače ( CR-Touch ,Pinda probe V1) a pod ventilátor jsem nalepil Led pásek 12V ktery je ovladaný od ventilátorů + odpor 620 ohm

Remixed two designs together; unlike all other designs, first one didn't interfere with CR touch, 2nd had Ender logo I liked.

Satsana fan duct with cr-touch bracket cutout for 4010 or 4020 fans, compatible with Ender 3 and Ender 3 v2.

This is a Mounting Plate for the Revo Hemera XS with BL-Touch + 4020 Fan. It fits on Creality Ender 3 / 3 Pro / 5 / CR-10. ... Enjoy ;)

... For the Mounting Piece on CR-10/Ender, Visit Remix Source Design by RegisteredThing at https://www.thingiverse.com/thing:3148733. ... I Haven't Printed This Yet, So If You Do, Please Share Your Experience with the Above Design.

... orientation of the original bottom_bracket by stevenfayers to accept the cables from behind. ...All credits to him. Print Settings Printer Brand: Creality Printer: CR-10S Rafts: No Supports: No Resolution: 0.25 Infill: 100% Category: 3D Printer Parts

UPDATE: I added additional tube ends that have the thread size expanded to 8.32mm diameter for those that may be experiencing threads coming out a bit too small. Try these and see what you get. I also included the STP and X_T files if you need to...

UPDATE: I added additional tube ends that have the thread size expanded to 8.32mm diameter for those who may be experiencing threads coming out a bit too small. Try these and see what you get. I also included the STP and X_T files if you need to...

Humans designed a solution to stop dust from entering the bearing atop the z-threaded rod. ...Simply printing this part ensures a perfect fit.

I was determined not to move the z-axis limit switch, so I designed and printed this clip instead. It attaches to the left-end of the x-axis gantry, causing it to contact the limit switch earlier than usual. The thin end goes on the bottom. After...

I designed a basic tensioner to be mounted on the 20x20 extrusion for effortless belt tightening on my cr-10s5 when using a gt-2 belt at the top of the lead screws to prevent gantry drift. Frustrated with constant adjustments, I decided to take...

Remix of https://www.thingiverse.com/thing:4697079 to fit an Ender 3 V2 only. ... And adjusted the BL Touch bracket to fit a CR touch as well, so you can use either of the two.