creality 5 plus 3d models

Use the same information as the original file, this just adds a slot to store one additional SD card on the side From original: So I made this thing for my Ender 5 Plus +, you need a couple of M3 or M4 x 10 bolts and T-nuts to attach it. I also put a...

This is a remix of the switch mount for the 3DChameleon MK2 that fits in the rear left corner of the Ender 5 Plus sitting ontop of the corner bracket allowing for you to use the Y axis to trigger the switch. The switch ends up triggering at the same...

# WHAT THIS 3D PRINT IS NEEDED FOR AND WHY IT WAS DEVELOPED: This 3D print resulted from the fact that after a while the cable guide of my Ender 5 plus kept bending towards the heatbed due to the weight. After a while, the cable guide was so deep...

Made a mashup of my previous remix for the ender 5 plus and the mini satsana for the ender 3 (Ill credit when i can figure out which one) You will need to add custom supports under the two risen areas for the BLTouch mount. otherwise no other...

Ender 5 Plus bracket designed specifically for SKR 1.3 and 1.4 motherboards, optimized to provide easy access to the SD card slot and USB port. To assemble this bracket, you'll need to locate and carefully cut a precise slot and hole on one side of...

I'm Sick of Long Bowden Tubes and Backordered Hemeras, So I Designed a Direct Drive Mount for My Ender 5 Plus. I'd had it with the lengthy Bowden tube that always seemed to be in my way. Then, when I was ready to upgrade to a Hemera, it went out of...

After purchasing Exoslides for my Ender 5 Plus I found that the H2 adapter wasn't compatible with the exoslide. Installing this requires disassembling the H2 to screw the center section of the extruder to the adapter. Next step is to connect the...

My Ender 5 Plus was extremely loud, so I changed all its fans. The loud one at the nozzle was swapped with a 40x20mm Cooltek one (very nice result) and so it did not fit into the normal metal duct. This one is designed in the same style, only...

The metal grate on the Breville Bambino Plus drip tray does not sit tightly on its plastic reservoir, so it rattles around while the coffee machine is running. I've designed some small shims to attach to the plastic reservoir that keep the metal...

My ender 5 plus factory spec out the box has this additional dampening bracket. Which needs slightly more space for the cover to fit properly. Test prints fit perfectly. Use the same fastening / fixtures listed in the original. ...Worked a treat.

If you own an Ender 5 Plus and install the Printermods MDD 1.2 direct drive plate, you'll discover that the stock metal BLTouch mounting plate won't fit properly. None of the pre-printed BLTouch mounts match, so I chose to modify the metal one...

I needed a convenient and fast Bike Mount for my Garmine Fenix 5 Plus, just like the Quick Release Mount I used on my Forerunner 935. Finding one was not easy, so I decided to design one myself. ...I came up with three designs: - The first uses the...

This is a Cable Holder for the Ender 5 Plus with linear rails and the Micro Swiss Direct Drive I use this cable chains 20x10mm: https://www.aliexpress.com/item/32999589537.html?spm=a2g0s.9042311.0.0.27424c4dZDh4ri I use the cable chain trays from...

Printing: You'll need ender 5 plus to print this, so disassemble it after all parts are ready. I printed with black PLA leftovers. Case and side vents with 0.4 nozzle and 0.3 layer height. Fan covers with 0.4 nozzle and 0.1 layer height. All...

No Support needed, 4 brackets needed for Ender 5-Plus I made this adapter to quickly fix the Z-Rod height on my Ender 5-Plus while using the Mini-Me Mosquito mount to avoid collisions. The BL Touch needs to be spaced down about 15mm to be used in...

Custom electronics enclosure for Ender 5 Plus printer. Takes standard Meanwell power supply and heated bed MOSFET & standard touchscreen. Designed to work with either SKR 1.3/1.4 motherboards. Due to their size, they need to be printed on the E5...

However it adds even more inches on height measuring 5.47 by a staggering length of approximately five point two eight four one nine inches which could take up some additional room on that bigger six by a larger plus phone when not inside one's hand...

... is fit to print on the Ender 3 and Ender 5 Plus. **A note on the Ender 5 Plus version:** It was designed to push the limits of the printer. I had to slice the white ghost part without a skirt in PrusaSlicer just to get it to fit the bed. ...

See the original creator here: https://www.printables.com/model/436006-ender-5-plus-with-microswiss-ng-cable-chain The original creator made these for a 10x15 cable chain that was purchased from Amazon. He used the closed version of the chain,...

To attach the raiser to the frame of the Ender 5 Plus you can simply use M3, M4 or M5 T-Nuts. You can get them here: ...

... This keeps the extension arms firmly in place on the front 20x40 extrusion. Print Settings Printer Brand: Creality Printer: Ender 5Rafts: No Supports: NoResolution: .2 Infill: 25% Filament: Duramic3D PLA+ White Category: 3D Printer Accessories

... need it. ...I have not printed this yet but please tell me if it needs to be fixed. Print Settings Printer Brand: Creality Printer: Ender 5Rafts: No Supports: YesResolution: 200 Infill: 15 Filament: Ziro PLA Black Category: 3D Printer Accessories

I used the 2020 frame clip-on of the “2020 Extrusion Webcam Mount [No Hardware] Logitech C270” found on thingiverse (https://www.thingiverse.com/thing:4636337) and the cable tree holder of the “Ender 5 / Ender 5 Plus Print Head Cable Strain Relief...

This is a case that I designed to use Klipperscreen with the Waveshare 5 inch DSI display (800x480) in the Sapphire Plus (SP-5) or Pro (SP-3). In addition to KlipperScreen, it can also be used with Octoprint with Octoscreen. It can be installed by...

This print is for side mounted light bars for the Ender 5 Plus. I wanted them on the sides so they were out of my way and have two light bars for better lighting. The brackets are RH / LH so the X axis motor on the gantry is the RH bracket. I also...

This upgraded version of the SpeedDrive v1 mounting bracket by sashalex007 eliminates geometry that interferes with the limit switch on the Ender 5 Plus. To convert an E5P to direct drive, all you need is a 400mm (16") stepper motor extension cable...

This fan shroud is designed to specifically fit an Ender 5 Plus with Spider Hot End using the HBE X Carriage (purchase on eBay). It allows the reuse of the factory fans and BL Touch mount while providing clearance to the linear rail mounts. This...

This is a case that I designed to use Klipperscreen with the Waveshare 5 inch DSI display (800x480) in the Sapphire Plus (SP-5) or Pro (SP-3). In addition to KlipperScreen, it can also be used with Octoprint with Octoscreen. It can be installed...

LCD Enclosure for the BTT, BigTreeTech TFT50 display to replace the Creality stock display on the Ender 5 Plus. (May work for Ender 5 Pro .. ...but I don’t have one to test)

I only used the dial for mine - personal choice) - STEP 5: Either cut the component circles and prongs from the 'Drilling Guide' -OR- print a 'NoGuide' - STEP 6: Fit into to Case then fit TFT35 v3.0 to adapter plate - STEP 7: If using the 'Cover...