creality cr scan ferret 3d models

I've modified the original hot-end-mount design to make it more compact and suitable for shrinking and easier printing. ...Paired with a slimmed-down fan, this setup offers a seamless blend of performance and convenience.

The most valuable upgrade for Ender 3 is installing motor dampers, and I'm telling you that from experience. I've printed a lot of mods, and most look great but don't actually improve the printer's performance. Not so with dampers - they make a huge...

I remixed CR6-SE screen cover. ...This one is with handle so its easier to pick the cover up.

I wanted to design a cable chain system for the x-axis on my Tevo Tornado, rather than having cables dangling everywhere. I thought others might share this sentiment. My inspiration came from a model at the link:...

I created this design specifically for mounting inside the printer enclosure. It securely attaches using 3mm countersunk screws. -The Allen wrench fits perfectly into its slotted hole, preventing it from moving around. -A small piece of tape is...

Raising your filament to meet the bed or part is a sign of a successful print. This feat requires no additional hardware. ...The mount attaches seamlessly to the extruder motor.

This is a dial gauge holder that mounts onto the extruder of the printer. ... It uses friction so no hardware or modifications to the printer are required.

<p>Did a quick remix of the auto off switch for the CR6 se. Used the stock CR6 power switch from the bottom power plug. It's somewhat thin, it may be necessary to remix it. ...It's adjustable, and is bolted to the hexagonal hole in the bracket instead...

This is a remix from https://www.thingiverse.com/thing:4491805 This is a remix a made for the bondtech clone, i also advise you use a nema 17 flat stepper so your build space doesnt get smaller. Havnt tested the upper areas of the printer for...

Here's how you can easily convert your 3D printer into a versatile plotter. ...Check out the comprehensive tutorial right here: https://medium.com/@urish/turning-your-3d-printer-into-a-creative-tool-3e9c4b8b89f0

Thought I'd share this Blink Mini cam x mount with a ball socket joint to receive the stock Blink cam mount ball. Nice and sleek. Enjoy! ... ...

Болт M5 x 20 - 2шт Гайка M5 - 2шт Болт M4 x 10 - 2шт Гайки т-образная M4 - 2шт Солянка из разных заготовок.

Compact BL-Touch integration in the design by @evil_k Screws for BL-Touch are M3x8 and they do not screw into the mount. They are only used as a guide so that the springs are not falling out. For mounting you need 1x M3x10 (top right) and 1x...

2018 03 24 stronger holder - verstärkte Version This dialgauge is held by gravity. So it can easy be attached to the profile. The weight of the dial gauge holds it in position. For snap on mounting look at my version 2...

I had cooling problems with PETG along bridges and overhangs so I printed upgraded fan duct but that wasn't enough. Then I tried another one which blows from two directions but it didn't flow enough for some reason. So I combined those and cooling is...

Replace the boot liner's blanking plate with a light insert to illuminate more space in the vehicle's trunk. ... Reduced by 1 mm to prevent impact during printing.

My control panel frequently flipped over as the filament became lodged between the spool's edge and the next layer. ... My workspace is an everyday Ikea office desk, but you can easily adjust the design to fit your own work surface, regardless of its...

A viewer shared these niffy automotive Calipers (typically used for for measuring tire tread depth and bakes). However they are super cheap and when I say super cheap, I am taking dirt cheap so a thousand and one uses ran thought my mind and this...

The slide prevents the cable from catching at the rear end of the frame. (Spray a few silicone at the top of the slide to improve the sliding of the cable sheath on the slide). ... The slide is attached to the frame using M3 screws and “T-nut M3...

To assemble the printer, first, remove the small knobs underneath the printing bed. Then, place the printed knob on top of the original small knob and secure it with a screw. Support this project for more high-quality designs at no cost. ... Last...

This model is an adaptation of the original to be able to calibrate your print bed more accurately by adding a dial gauge to check the height. In its lateral part, add to hold the support with the same screws of the Layer Fan and avoid imprecise...

I adjusted the files to lower the fan by an additional 1.5mm, putting it into a suitable position now. I've downloaded and tested various hotend mounts, and I strongly believe that the original positioning and size of the two mounting screws are not...

I like the look of the blue LED, but it's rubbish to actually see the print. A fan duct seemed the ideal starting point for adding more! The original fan duct design from Kroffty is amazing. I just added the ability to put some cheap LED lights from...

Direct Drive Mount for Stock CR10 V2 Extruder Prints Very Quickly, Extremely Easy to Use. The extruder faces forward for a clearer view of the drive gear. This makes it easier to work with the extruder and check its performance. There are two...

Basic assistance is available for standard Chinese lasers that use four magnets.

I'm aware that fan covers can introduce extra noise to the system. I noticed that many fan covers on Thingiverse are visually appealing, but their design isn't intended to minimize noise. This project aims to address that issue. Here's what I did: ...

Added a 5015 fan mount and air duct that effortlessly slides over and is secured with hot glue onto the fan opening. Additionally, mirrored cable duct and installed a zip tie post on the opposite side for enhanced organization. ...Cura prints smoothly,...

I had previously printed a version of this part, but unfortunately, it was my own mistake that caused the print to break and now my pneumatic fitting consistently loses grip on the tube, resulting in ruined prints after several hours. To address this...