creality ender models

- Creality Ender 3 Pro Hotend Plate - Creality High Temperture Hotend - 12 mm inductive bed pobe sensor - 5015 radial part cooling fan - Fan duct is mechanically separated from bed level sensor It is not modular, but you can adjust the duct height a...

Creality Ender 3 Pro X MGN12H 300mm Linear Rail No Mods Light Simple Fast single y bearing support Easy to print, suggested PETG No modifications required but just to adjust Y endstop 3mm forward and a proper leveling Fists standard or Micro Swiss...

I could not find the perfect shell for my taste and need (fitting it upside down to the lower side rail of a Creality Ender 3 Pro to run octoprint), so I took the most good looking I found IMHO, and tweaked as needed. Here are my edits: - added...

Known printers that they work with: Ender 3 Ender 3 V2 (Take the version for a slot for the rear profiles). Voxelab Aquila Tevo Tarantula Creality CR10 V2 (use 2 slots high) Anycubic Vyper If you are worried about the printer slipping with these...

Recently, a full 1kg spool of fresh expensive filament slipped off my standard Creality spool holder on my Ender 2. I am printing on my attic next to the stairs. As I started to feed the filament (with the hatch to the stairs still open) I slightly...

(However this will work with any creality ender style printer.) The idea behind this was to make the most compact and lightest way of mounting the orbiter, two fans (one 5015, one 4010/4020), the fan shroud, bltouch and the trianglelabs dragon hotend...

The model has 1mm support poles built in, they snap off easy and I have a thing about support, best avoided :o) There's a pre-chopped G-code in there, for Ender 3 - with 3 shells, 1 percent infill with gap filling at 0.2 layers, perfect for most...

... I modified the arm for the BL Touch to match up with the cable for a CR Touch and removed the access hole for changing the BL Touch probe since the CR Touch does not have a replaceable probe. ...I am using this on an Ender 3 v2. ...

This is a quick description on mounting the LJC18A3-H-Z/BX on an Ender 3 as an alternative to ready made kits available on the market. You need some soldering skills and a bit of electro-technical knowledge. If you don't know what you are doing, buy...

Here are some links related with getting Octoprint on OrangePi Zero and fix it on Ender3: - My mod to stick orange PI zer on the Ender 3 frame (https://www.thingiverse.com/thing:3476249) - Octoprint on Orange PI zero Non-affiliate links: - LÖRBY -...

... handles of the Creality pliers, printable without supports. ...The 2 pliers are different to put the spring. Here are the parts to replace the handles of the Creality pliers, printable without supports. ...The 2 clamps are different to put the spring.

... Update 1.0 I noticed a 2mm overhang on the top bracket that blocked the bed carriage from reaching the endstop, so I remade it and am printing a new version now. The revised design works flawlessly and is currently installed on my Ender 3.

... deal at this price! E3D V6 Hotend required. You will also need Bond Tech Gears Original or Second Source for the Direct Drive Edition. Designed and thoroughly tested by K&K on Creality Ender2 and Ender3. ...Print quality is incredibly insane!

This is to be used with Hangtight's newest Ender/CR10 Hotend mount, when using a BMG clone (or BMG?) Extruder in a direct drive setup. This mount is a remix of the SpeedDrive v1 BMG mount and I essentially moved the extruder 4.4mm forwards to line...

:-) This mod is verified to be compatible with: - Ender 3 S1 - Ender 3 S1 Pro - Ender 3 S1 Plus As of version 4.0, this duct is compatible with: - Spider Hot End Mod (3.5mm lower, use the provided STL, not the stock one) This mod is NOT (yet)...

This is a remix of Skia_MKX's remix of Satsanas design for the fan ducting for the micro swiss direct drive conversion for the ender 3's and the CR-10s to allow use of the CR-Touch. https://www.thingiverse.com/thing:4933205 The reason I remixed...

Warning: You'll need to flash a bootloader on your Creality Melzi board. This will erase your original firmware. You'll need to install an alternative one: https://www.th3dstudio.com/knowledge-base/th3d-unified-firmware/?seq_no=10 NO RESUME ON...

... Edit: Experienced problems with high-retraction models where the extruder gear was chewing a flat spot into the filament, so uploaded an updated extruder bracket with a 3mm offset for the spring instead of 4mm to reduce pressure on the filament.

Since my CR-10 is an old model, it only runs 12V and does not have too much headroom anyway, considering it has a 300x300mm bed to move as well as a DD extruder.<TL;DR>Make printer go brrrrrrrrrr not squeak pop taktaktak :DSolutionDesign a...

... end as long as the flatted 5 mm axis remains accessible. Enjoy this new design! If you like the style, here is the full set of knurled knobs for the Ender on Thingiverse: | Extruder Knob | Z-Axis Knob | Control Knob | | --- | --- | --- | | | |

This is a non-printing design, instead serving as a mockup of the Creality gantry tensioner's plate and screws. ...You can build upon this model to create your own custom designs.

I tried various coolers but none impressed me, most simply blew air through the nozzle or in a small area around it, resulting in subpar part cooling. I decided to create my own cooler from scratch, drawing inspiration from...

This is a remix from https://www.thingiverse.com/thing:2819859 https://www.thingiverse.com/thing:2622840 I tried to find a cooler I liked but nothing seemed to work as I liked, most seem to blow air at the nozzle or just in a small area around it...

This is a remix from https://www.thingiverse.com/thing:2819859 https://www.thingiverse.com/thing:2622840 I tried to find a cooler I liked but nothing seemed to work as I liked, most seem to blow air at the nozzle or just in a small area around it...

<p>Remixed to take a length of PTFE tube to prevent filament rubbing against the lead screw.</p> <p>Note: it's a tight fit for the PTFE tube, by design.</p> Category: 3D Printer Extruders

Remixed, https://www.thingiverse.com/thing:3176144 Added rotating trucker style knob for ease of use, function etc. ...

The custom-designed case is tailored specifically for the dual step-down module, allowing it to seamlessly integrate into the frame of the Creality Ender 3 Printer and other similar models from Creality.

models

models

A thing to replace Ender 3 QR Code with Creality logo