csl elite playseat challenge 3d models

Ich brauchte etwas, um Fanatec CSL Elite-Pedale an den Playseat Challenge zu montieren.Ich habe dies in PETG gedruckt, aber PLA sollte auch gehen.Es gibt 2 Varianten, eine für M8 Schrauben und eine für M6 Schrauben (falls man keine M8 zu Hause...

These mounts do not require you to remove the foam of the Playseat Challenge and they allow the CSL Elite pedals to be used in either the farthest apart position or 1 notch in. A 10mm Wrench is required if you do not wish to remove the footplate on...

This universal mount allows you to affix both Fanatec V3 & CSL Elite pedals to the Playseat Challenge.These mounts do not require you to remove the foam of the Playseat Challenge and they allow the CSL Elite pedals to be used in either the...

No need to take the pedals plate.Don't go crazy tightening the nuts, just make sure the mount is secure on the pedals and cannot move.Put the pedals to the Playseat pedals mounts.Tighten zip ties by dragging back and forth.Cut down the excess using...

* Install ZipTies in mounts * Tighten ZipTies around Playseat Challenge by pulling down then pulling up * Trim ZipTies Requirements: ============ * 1x 5mm Allen Key * 1x 10mm Wrench * 8x ZipTies 5mm * 2x M6x16mm Socket Head Bolt (low profile, so it...

Recently purchased the Fanatec CSL DD Wheel & CSL Pedals combo intending to mount on my Playseat Challenge. The wheelbase mounted fine, but the pedals had no good way to mount rigidly other than the large velcro strap that comes with the Playseat. ...

This brace is designed to prevent the CSL DD from getting damaged when used with the playseat challenge. ... More Information: https://github.com/team-sillex/simracing_mods/tree/main/CSL%20DD%20Playseat%20protection%20brace

... Pedals delivered e.g. ...with the Fantatec GT DD Pro. For mounting on the PlaySeat Challenge. ... Material List: 2 M6 * 30 mm screws (for the front clamps) 8 M4 * 20 mm socket head screws 8 M4 Nuts 2 M5 * 16 mm screws 2 M5 Nuts 2 Washers for M5

The Fanatec CSL Elite LC pedals enable repositioning of the pedal models into various locator holes in the heel rest. The set includes hardmount points, although minor details are excluded. The brake pedal is a loadcell variant. These pedals may be...

This Holder is designed to mount the Fanatec CSL DD Power Supply directly to the Playseat Challenge Racing Seat. The Holder is designed around M4 Threaded Heat Inserts and M4x12 Bolts. I use it, to mount the 5Nm Power Supply. ...I don't know, if it also...

<p>I hate printing and removing supports. Here, i've blanked unsupported holes 0.2mm thick so you woulndn't have to.<br>Just punch through or remove them with something sharp after it's printed. ...No other changes made.</p><p>I'm unsure what license...

Clamp to hold the Playseat Challenge chair closed.

The 3D printed parts necessary for enforcing the playseat challenge for fitting a CSL DD. Assembly: https://imgur.com/a/fHWt52l I've used a 40x3mm aluminum bar. Around ~1,2m or so of it to connect everything in between. The part i called...

A few straightforward clips keep the playseat challenge neatly folded away. ...I didn't care for utilizing the straps; these simply snap onto place and function perfectly fine.

Mount this versatile clamp securely to a playseat challenge or other objects featuring 25mm tube diameter. I successfully utilized it to attach the power supply. ... Required hardware includes: Two M4x30 screws Two washers designed for M4 Two M4 nuts

A set of mounts designed to rigidly mount the Fanatec Clubsport V3 pedals to the Playseat Challenge. May also fit other pedal sets. ... More Information:...

A set of mounts designed to rigidly mount the Fanatec Clubsport V3 pedals to the Playseat Challenge. May also fit other pedal sets. ...More Information:...

I designed this part to attach under the 21mm tube on my Playseat Challenge chair, raising pedal height for a more racing feel during drives. I printed two units and reinforced them with metal plates to boost strength. ...A hole was included in the...

Adding a adapter to the Playseat Challenge on a side area is a fantastic idea. It works beautifully with my E-brake, which I've thoroughly tested. I printed the adapter using PETG infill at 15% and 20%, and it has plenty of strength without breaking....

The playseat challenge comes with two plastic clamps to mount the pedal mount to the chair frame but still allow it to fold.One of mine broke - so this is a replacement. ...Uses M6 bolts - but still allows the chair to fold away.I printed two in PETG,...

I prefer a higher stance than the standard playseat challenge setup, so I fabricate a T connector and foot for a 21mm rod.\r\n\r\nThe custom part features four screw holes for 4mm screws and nuts.\r\n\r\nThis adjustable foot is designed to prevent...

This clamp reinforces the entire pedal plate and makes it possible to use load cell pedals on the playseat challenge. I printed this in PLA 0.2 layer height. It's best to use supports inside the nut inserts for the bottom pieces. ... necessities...

I wanted to experiment with angling the pedals of my playseat challenge like some higher end rigs do. V1 attaches at the far end of the pedals, and would probably work well on hard floors. In my case, the carpet pad made the pedals rock side to...

This is my favorite modification for my Playseat challenge. This cupholder will fit a water bottle (or beer) while doing some Sim Racing. No more awkward reaching to stay hydrated while in the pits! Take a sip of your favorite ale on the front...

This is a can holder for the Playseat Challenge or other brands of racing chair. For anyone wondering why I made this and don't just simply put my drinks on the floor, well, I have a doggo, and he likes to touch things that are on the floor. This...

Feet for the Playseat Challenge. Designed to fit some 50mm x 50mm glider or rubber pads. The glider allow me to easily move my seat around. The front feet can be fixed using zip-ties.</p><p><strong>Important:</strong> I designed the feet of the seat...

So, I went through the 10 realistic wheel plate positions for the playseat challenge, and did my best to measure what length and angle each one would need to function. I incorporated that into a dynamic FreeCAD model, where you simply have to enter...

I am actively redesigning this box as I've realized how little room it currently has for the hardware.** **Additionally, the clamp mount is not the best as it does come a bit loose over time and is not held at the best angle, nor is it at all...

Dashboard to slide in a Galaxy S8 from the left, compatible with CSL Elite Wheelbase and Formula V2 Wheel

Additional accessories for the Fanatec CSL Elite pedal systems are now available, manufactured using a combination of PLA and TPU materials.