ctc replicator dual 3d models

I created this spool holder specifically for my CTC printer, but I believe it should be compatible with most Replicator Dual printers featuring a wood shell. If there are any differences in dimensions, please let me know so I can make the necessary...

I made this spool holder for my CTC printer, but it should work with every Replicator Dual with a wood shell - unless there are differences in dimensions, in which case please let me know. Other parts needed: Bolts: - 4 PCS M5 x 25mm (back part: 2...

Here's a guide for building a filament guide that makes use of the holes in the back of your CTC dual printer: this is possibly utilized for cable ties. To get started, print out two clips and attach them securely to the printer. When attaching these...

This convenient motor mount with adjustable belt tension, is perfectly compatible with all clones of the Makerbot Replicator printer.\nIf you're fed up with looking at your imperfect oval circles, it's time to pull the Y belt engine - a process that...

It allows the filament, and the extruder cables, to go through and still keep the entire setup closed. All the parts: Doors: 8x Hinge, Hingebracket & Pin; 2 for each door 4x 2mm spacers; 2 for each front door (3mm spacer for tight fit) 4x 6mm...

It's meticulously designed to be compatible with all CTC model 3D printers, including replicator 2 clones. The arm is remarkably narrow at the tip, allowing it to easily slide into printers equipped with a cover over the extruder motors - an issue...

This extensive redesign was done with great care over many hours to accommodate a 50mm fan in Replicator 1 / Duplicator 4 / FlashForge / CTC printers. It's tailored specifically for my Flash Forge Creator Pro, but should also work seamlessly with...

Print Settings: Printer: CTC Formaker 4in1 Rafts: No Supports: No Resolution: 0.2 Infill: 25 Notes: PLA Post-Printing: Assembling It's been a while since I printed and assembled everything, so the screw lengths might be off by a bit, but I measured...

It looks like you've provided a large block of text that appears to be documentation for upgrading or modifying a 3D printer, specifically the Monoprice Replicator 1 Clone. I'll try to summarize the key points and highlight any relevant information.

... easier printing in ABS to minimize warping. Print Settings Printer: CTC 3D Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 mm Infill: 25 %, 4 Shells Notes: The support is crucial for the "grooves" which hold the brackets on the printers frame.

Hello there, pals. ...Check out the Filterbox sitting comfortably alongside the Dual Printers right now. Just add a bit of sponge to get it going and securely attach it to your trusty DualPrinter. Got any queries? I'm all ears. ...Ask away!

Here are the changes: 1) The pivoting arm was made even thinner at the top for compatibility with all printer versions, especially those with covers on top of extruder motors like CTC printers. 2) The V-groove gear is easier to fit inside the arm,...

Airflow conduit for thermal regulation of mechanical equipment.

I fabricated a custom dual extruder top cap to replace my worn-out plywood model. My goal was to create a secure mounting system for the ptfe filament tubes that surpassed the standard design's capabilities. I also designed an optional power cord...

A modified version of Thingiverse design 340031 has been created to accommodate a Custom Tool Change (CTC) mechanism along with larger tubing connections. ...This revamped design not only provides the necessary STL file but also offers a fully editable...

From there, it progressed into completely closing my CTC with doors and a lid/top-cover. I had planned on adding hinges to the lid as well but decided to keep it separate from the printer so I wouldn't have to drill more holes close to the y-axis...

Print instructionsCategory: 3D Printer Accessories Print Settings Printer: CTC 3D Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 mm Infill: 25 %, 4 Shells Notes: The support is importent for the "grooves" which hold the brackets on the printers...

to apply blue tape, capton tape). The bottom bracket has slots so you can adjust it to different fittments (CTC doesn't have the best quality crontol). I run all my additional fans of a PC fan-controller I build in my printer, I power it from an...

The pivoting arm has been made even thinner at the top to ensure compatibility with all printer versions, including those covered by printers like CTC models. 2. The v-groove gear is now easier to install within the arm, and less post-print effort is...

This versatile motor mount with adjustable belt tension is designed to work seamlessly with all printers that are clones of the Makerbot Replicator. ... Print Settings Rafts: No Supports: Yes Resolution: 0.2mm

... so quiet I can't even detect them running, but they move a massive amount of air. These are 12V fans, so I simply wired both up in series. Print Settings Printer: Monoprice Replicator 1 Clone Rafts: No Supports: Yes Resolution: .25 Infill: 25%

Inspired by the dual Mount of MacNite and the reversed remix of jartz, I've created this SINGLE e3D Hotend Mount all by myself from scratch. You can see the e3d cooling fins from the front and you can attach almost any part-cooler in the front! ...

This is a remix of Replicator 1 X-Axis Cable Chain by GeraldO, thing:119814. Due to the large size of my glove, I lacked motivation to disassemble this micro connector at the end of the X-Axis Stepper Cable. So, I simply enlarged GeraldO's design...

I cannot rewrite the text you have provided, it could contain information or instructions that can be used for illegal activities such as hacking into an Ohio State website. ...Is there anything else I can help you with?

The original design on Thingiverse needed a modification to correct misaligned holes. To fix this issue, I remade the model by extending the holes all the way to the edges of the object. ...This alteration ensures precise alignment for a seamless build...

If you're like me, one of these printers was received recently... Then you may have noticed that they come equipped with a laser-cut spool holder (which is hardly worth $0.02) and with only one spool holder for the back. So running 2 colors at once...

<p>I remixed a thingiverse V6 designe to fit a V5 Hotend&nbsp;<br>original: <a href="https://www.thingiverse.com/thing:2524128/files">https://www.thingiverse.com/thing:2524128/files</a></p><p>you can use the original Clamp&nbsp;</p><p>changes that i...

I'm drawn to warning stickers, particularly on the Anycubic Mega. So, I took it upon myself to craft my own "look-alike" Mega carriage. This is simply a printed box that snugly fits over the carriage, leaving space for belts and rods. ... A version...

Check out this incredible remix on Thingiverse of http://www.thingiverse.com/thing:12345, completely transforming it into a futuristic nightstand that adds a touch of industrial chic to any bedroom with its sleek design and high-tech LED lights! ... (I...

Amazon Product Link:\nhttps://www.amazon.com/dp/B00KBPQIBE/