custom built 1 64 scale trucks 3d models

The stock Creality stepper was 1.5A, for instance, my 23mm stepper is 1A, I tuned the VRef E1 voltage down to 0.8V. (how-to reference: https://support.bondtech.se/Guide/22.+Creality+3D+CR-10S+Pro+-+Stepper+Current+Adjustment/47?lang=en) After the...

Also remove 1 x M2.5 Allen screw in the middle but not the one holding the square stabilization piece.Remove the power supply. It is held by 4 x M3 allen screws attached to the printer (one is hidden behind the cover so be sure to remove that...

These tabs keep the arrows in place when theyre inserted and prevent them from sliding out. Sled Gather all of the parts from the Sled_Assembly and get a short peice of filament (1.75mm). Check the images for the names of each part. This part is a...

TPU: I use is TPU Flexible and Tough (https://filaments.ca/collections/all/products/polyurethane-tpu-filament-dark-green-1-75mm?_pos=10&_sid=6758b4aab&_ss=r). NB : IF YOU USE 100% INFILL, YOU DON'T NEED TO ANEAL YOUR PARTS... Annealing you APLA+...

Follow the Wham Bam Mutant setup documentation for instructions on wiring your HotEnd assembly to the Mutant Mobile plate. Step 1: Select the Hero Me Mutant components for your specific 3D printer and HotEnd setup and print them. PETG is the...

These extensions are just to hold the gears in the right position.Cutting threaded rod is easy with a hacksaw, just make sure to use a file to clean up the ends afterwards.Arbour 0 (which has the cord wheel and hands) needs to be 11cm longArbour 1...

A 1 mm hole carefully drilled in the rear end and packed with the same fuel with an added 10% baking soda will serve as a delay to further pyrotechnics e.g. parachute eject. ...bungs should be fairly deep 2-3cm is sensible.</p><ul><li><a...

I recommend adjusting the height of the cooling ducts so that the bottom of the duct tips are ~1.5mm above the nozzle tip/bed surface. You will need to measure the X/Y offset of the ABL sensor to the nozzle and either add that to the firmware as...

**EDIT 5/1/19** Minor change. After printing again with changes (used eSun PLA+, .6 Nozzle, .4 Layers, 2 Walls 20% Infill) I discovered another problem (remember, this is a remix). The fans were still not properly secured. I added some more...

The dissolved PVB will then later also act as some kind of glue to completely fix it.1. Smoothing the inside</strong></h4><p>Smoothing the inside of the glasses is the most critical part of the job: with the small hole on the top, IPA will evaporate...

This might be one of the last designs from my old customizer, since today, I released the first version of my new tool. The new tool gives full flexibility over everything, you can individually rotate arms now, add your own libraries and the tool is...

The main problem is precise printing over large distances with multiple parts. I've strengthened the radiator support on the PCI-IO part, as it was too flexible during printing and led to less than clean prints. V0.33:added more supports to the AGB,...

If you printed that set for the third edition stuff, you can now use the units as a faction (or in custom builds) for the new stuff! We've set up a Patreon page for anyone who's interested in helping to fund us so we can keep making free and open...

Custom STLs: - [DIN rail extension](/download:11266240) (optional - I ordered 500mm rail, these bridge the remaining 50mm) - [20A buck converter mount](/thing:5162363) (optional - you could use a lower amperage model) - Skirt corner pieces (TBC). ... ...

If you printed that set for the third edition stuff, you can now use the units as a faction (or in custom builds) for the new stuff! We've set up a Patreon page for anyone who's interested in helping to fund us so we can keep making free and open...

Two parts that clamp together around a tube such as a table leg. Rear Hub.stl  Front Plate-200.stlUse with the 200mm rail Front Plate-240.stl… Front Plate-280.stl… Front Plate-320.stl…Customization and the ModelI have provided a Fusion 360 file with...

Some components may need to be glued. The license plates are clear: you can customize them with post-processing, or modify the step files to extrude the characters, to be printed with different colors. All files concerning the detailed body have the...

Please check the images to see what it is included in this kit.This set contains: - Dwarven Berserkers (6 + 6)- Behemot Riders (4 + 4 + 4)- Durnir – Berserker Lord- Tarum Bloodhammer- Thyra Blood Priestess of Duum (Dwarf Pinup)- Skutagaard War...

If you printed that set for the third edition stuff, you can now use the units as a faction (or in custom builds) for the new stuff! We've set up a Patreon page for anyone who's interested in helping to fund us so we can keep making free and open...

I had used some custom clips to mount into my old aluminium window frames but they are a little awkward to deal with. Since all my windows have a small ledge I decided to make the array, "stand alone' so it would make it easier to move from one...

Please check the pictures to see what's in this kit.This set includes: - Requiem Demon Hunters (6+6)- Requiem Wulfhearts (4+4)- Captain Fenrir - The Silver Hunter- Captain Fenrir - Wulfheart Form- Trisha the Houndmaster (+2 Mastiffs)- The Old Wolf...

What is happening, that I learned with the classic view and had not used it since the last time I installed Windows (much to my regret there is no version for Linux) and total that I had no way to put the .cuix of the view classic because I didn't...

Please check the pictures to see what's in this kit.This set includes: - Apprentice Arcanists (6+6)- Summoned Elementals (4)- Cornelius Greathat- Odessa Witchsword- Volrunax Runebeard- Morwina the Witch (Pinup)- Giant Clay Golem- Treasure Mimic (3)-...

Gives it an even tighter seam than the exacto, but also a more matte finish. Let me know if anything is missing. Custom Section Printing I recommend printing one piece at a time. It's time consuming, but you'll want more control in the end. After a...

The original bolt from the old tensioner can be reused.Uploaded a custom lightweight aluminium 3-point mounting plate, with new, smaller and lighter rail mounts and a drill guide to go along with it. This new setup weighs 102g (new plate is 78g),...

If you are looking for more, check out our premium projects: https://codeandmake.com/premium You will need Tools A computer with Arduino IDE installed and a mini USB cable. Soldering iron, solder and flux. Hot glue gun and glue. Wire...

During the last week, I was working on including all the stuff from my old heavy space soldiers customizer to the new one. But wait - these do not look like heavy space soldiers... Actually, you can mix the different parts together, so these have...

And also connected the LED to a constant glow so as not to forget to disconnect the power cable when moving the machine. Shortened the display cable and motor cable by placing them in the profile slots, and added a few more cable clamps. The...

For example, like here:Now this is such a thing, and as it turned out, it is quite applicable for small parts.There is nothing unusual in the video, except perhaps the operation of a new laser and post-processing with a new sander. The laser itself I...

And as a feed roller, I used a roller from a Cricket lighter, it fit perfectly in size.The battery charge module can be used from a ready-made charger by cutting off one piece. But at the moment I have created my own modules, which I already actively...