custom robo gc 3d models

I will be answering questions there and I look forward to seeing pictures of people's in-progress builds: https://www.thingiverse.com/groups/curta Update 6/27/2017: The main axle and step drum model have been updated. The old one works, but the hole...

I've updated the model with the Orbiter Ver. 1.5 as I purchased another one (I don't want to take the one I'm using on my Bear off as it works soooo good). I've also updated the filament sensor to use the Prusa MK3+ sensor as I have two of them. I've...

They can easily be swapped around.PrintingMain HandleIn general you should use the flattest side of the model on the print bed. Your settings shouldn't be adjusted too much, the standard high quality settings of your printer (or whatever tuning works...

Tensegrity model maintaining stability with one single wire.Materials needed:0.5 mm nylon wire7x M3 nuts7x M3x10 mm Allen screws (longer ones were cut to the right size)wooden plank of about 55 cm2x 50 mm wood nailsThe spiral parts are designed to be...

 For me, it pressed in very tightly; if in doubt, glue it in.To mount the holder, I stuck this adhesive mount onto the back, and used it to replace the jaws of an older model of this suction base.  The adhesive mount’s socket is smaller...

being able to reprint the broken part vs the entire model is a plus. Except for the charging ports, no glue is needed. All the STL files have been positioned to hide the seam as much as possible (when possible). The Activator Assembly parts are...

also know with ESC if you turn power off with pot turned to high you have to turn the pot down to be able to start motor again (must be a ESC safety thing) Machine drilling a board the failed to drill completely through on the CNC PCB Mill ( My fault...

... <p>100%</p> <p><strong>Notes:</strong></p> <p>Print at 100% infill. The tubes are modeled hollow and should print that way Post-Printing Top Finishing Some finishing may be required for the Elite version of the top. Category: R/C Vehicles

(Not required for revision 2) Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the...

I simply used a couple of dabs of model car glue, but you can use epoxy if you prefer. I would avoid CA because the fumes may fog up the inside of the lens. The finished part is shown in "modified camera.jpg." I just checked Amazon and found that I...

Originally designed for the Ender 3-V2 model, reusing the 4011mm Original axial Fan as Nozzle cooling. The original fan is loud, you will probably wish to change it with a quieter one and higher performance 4020 axial fan! Many options are available....

# Anet AM8 motherboard case This case is inspired by a [YZ Case for Prusa made by Carter](https://www.printables.com/pl/model/1910-yz-case). This case is prepared for mount on the Anet AM8 modification frame. It can hold Anet A8 v1.7 motherboard...

Because of the simple geometry of the Box and the Pieces, these modest settings produce a very nice model in a relatively short print time. Please Note: Although I have not provided the solution here, I will respond to personal Thingiverse messages...

Furthermore I created the endstop mounts which are already present in the Fusion 360 model. I will try to update the pictures today or tomorrow. Now it gets exiting! Electronics are next! **Update 9** (03.07.2018): After test driving the Z-Axis I...

It looks like you've got a table with some planetary models and their corresponding scales. Here's the cleaned-up HTML for it: ```html <table> <tr> <td><a href="https://www.thingiverse.com/thing:3720464">Earth</a></td> <td...

Each knuckle is 35mm in length, axis to axis. As of 09/16/2018, I've not yet modeled or printed the capstan bearings, nor have I fully solved how I will drive the capstan. My current thought is to use a drill attached to the underside of the...

You will, however, need to modify the hole in the motor arm to fit your motor's shaft, after you have scaled the model. You may also need to do some modification to the connector arms so that they clip nicely to the connecting rod that you plan to...

Here is what I came up with:&nbsp;This model consists of 3 printed parts. Then you need something with ø3 mm diameter as an axle. Anything like a wire or nail would do. Just cut it to a length of 18 mm. Fix the lever in the holder with this and make...

More information: The models were printed in PetG and have a consumption between 5.7g and 7.0g and the printing times range from 0:47 to 1:15 hour. Note1: If the z selection alignment is used, you can generate a line as the one shown in the...

You can find the newer version here: Phone Mount for Van Moof S2/S3 V2.0====================================================================&nbsp;Rotating Phone Mount for the Van Moof S2/S3 electric bike.Mounts to the handlebar using 3 cable-ties,...

This model only cost 1 dollar because I am only pricing the topper and Star mount, the rest is free with the purchase. This is a pixel tree mount to build an eighteen string 216 degree pixels tree. Height can be up to 5 feet. The base design is...

Use at your own risk!!Check out the current version of this design here. This design is tested and ready for use, but only uses one blower, not two.</strong></p><h3>Basics</h3><p>This design stemmed from my desire to create a perfectly controlled and...

It is not intended to print and snap together but to model it in tinkercad via importing the object and duplicating it. I designed the battery mount to be installed over the forward bottle holder. I'm expecting to utilize stainless steel hose...

…unless you got yourself a special edition of a bobby car like a Porsche, Mercedes or the older Audi, VW or BMW models like I got. At most of the special edition you can’t fit the original push bar. I found the design of Klein-laui on thingiverse...

I probably should make that easier to do if when printing the full model instead of the slices (maybe an exercise for the one wanting to do that - add a better wire hole). I used a 2.1 bluetooth stereo board that I got on ebay for about $21...

The source of the model has several parameters that you may wish to change. The current settings are for a silicone tube with an internal diameter of about 4 mm. You can adjust the pen length and width to your preference. Note that some tweaking may...

Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the pictures, the standard STL size...

Note: these videos are uploading slowly, so they might not be fully processed when I publish this model. They should be available in a few minutes.</p><figure class="media"><oembed...

--------------------------------------------------------------------------------- Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support...

Super easy customizer for creating bolts, nuts, washers, threaded rods, and standoffs.Features:easier than other thread customizers, just pick a thread and configure details950 threadsfive types of bolt heads : standard, cheese, countersunk, round,...