da vinci filament 3d models
195524 3d models found related to da vinci filament.thingiverse
... the 3D printer, like shown in the picture. Hope you enjoy my design! Print Settings Printer: Da Vinci 2.0 Duo Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: At least 60% for minimal flex Notes: This goes on the handles of the Da Vinci.
thingiverse
I wanted a way to mount 3rd party spools on my Da Vinci Duo and found some good ideas here. I ended up printing this one: http://www.thingiverse.com/thing:433194/#files I then made these guides to help guide the filament around the back of the...
thingiverse
A simple adapter to hold bigger non-XYZ filament spool in place of smaller original spools.
thingiverse
... a Da Vinci 1.0 AiO. Remixed from fr333n3rgy's design, this new version allows you to use either an Arduino Nano or Arduino Pro. Read more on Instructables... https://www.instructables.com/id/Arduino-Nano-Da-Vinci-Filament-Cartridge-Resetter/
thingiverse
I designed this to be a direct replacement for the XYZ da Vinci filament spools inside their proprietary cartridges. I like to feed my printer from cartridges I refill myself because it keeps everything neat and contained and the stock cartridge...
thingiverse
Print it using the 'Good' da Vinci settings: Supports checked 3D Density = Low 10% Shells = Normal Layer Height = 0.3 Speed = Standard Clean the supports, drop the electronics in, snap it closed and it's ready. ... Go to dimensionbx.com for the...
thingiverse
... may result from using these parts. Print Settings Printer: Modified XYZ da Vinci 1.0 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: 100% Notes: My print settings for this are somewhat arbitrary, don't take them as gospel.
thingiverse
This is a remix of http://www.thingiverse.com/thing:800173 Changed to angled guide to have less friction Installed with a 6mm teflon tubing going through the hole for better performance This thing was made with Tinkercad. ...Edit it online...
thingiverse
Remix of the original part, da vinci pro filament guider by thaamike. A couple of members, including myself, requested the inlet turned up. This is my crude attempt at modifying a model (1st attempt at publishing). I provided a couple of...
thingiverse
This part makes sure that the filament of the da vinci pro is guided to the feeder. ...Print Settings Printer: Da vinci pro Rafts: No Supports: Yes Resolution: used 0.3mm Infill: 20%
thingiverse
Pretty simple remix. One piece. Twists into locking position. ...I was able to print without supports and just had to cut away about 1 string layer by the locking mechanism.
thingiverse
Filament guide for Da vinci Pro 1.0 Print Settings Printer: Da vinci Pro 1.0 Rafts: No Supports: No
thingiverse
This is a flush plug to block the unused filament hole on the da vinci jr
thingiverse
The da Vinci Jr comes with one filament spool holder. I wanted more, and learned a bit about TinkerCad along the way. ... Print Settings Printer: XYZ Printing - Da Vinci Jr Rafts: No Supports: No Resolution: .2 Infill: Yes ~ 10%
thingiverse
This is a filament holder I made for my XYZ Da Vinci Jr. 3D Printer. Print Settings Printer: XYZ Da Vinci Jr. ...3D Printer Rafts: No ...
thingiverse
I reworked my Da vinci pro to Marlin fimrware and TMC2208 drivers including filament change feature. Everything is quiet, fast and reliable. No more crappy slicer and crappy mainboard For extruder part I just removed plastic part with clip and cut M6...
thingiverse
It feels a bit light, so I would suggest 15% - 25% atleast on the tube section that the roll sits on) Not sure if its a good idea for it to sit like this but I will try soon with some external filament. Needs work. Edit: - Not very good. tried it...
thingiverse
Simple filament guide for the hole in the back under the lid
thingiverse
This is my bowden tube holder for the Da Vinci 1.0 It works perfectly along side my Super Mega Delux fillament holder plushttp://www.thingiverse.com/thing:735303 I was sick of tangles so designed this simple bowden filament guide for the back of the...
thingiverse
Filament holder, used on the back of the XYZ Priting PRO Printer, where it does not interfere with the upper door opening.
pinshape
SummaryThis is a Canola Oil oiler for the Da Vinci 1.0 3D printer. Glue it to the top of your extruder. Cut a slit in a cotton ball and apply Canola Oil. Wrap cotton ball around filament and stuff into receptacle. ...Lubricated filament helps to...
thingiverse
This is a Canola Oil oiler for the Da Vinci 1.0 3D printer. Glue it to the top of your extruder. Cut a slit in a cotton ball and apply Canola Oil. Wrap cotton ball around filament and stuff into receptacle. Lubricated filament helps to reduce...
thingiverse
After flashing my da vinci printer i turned to mathers3000 spool holder which seems to of printed out an is working really well: http://www.thingiverse.com/thing:727723 To add to this i also wanted to add a filament filter. Iv'e simply taken the...
thingiverse
After I upgraded my printer to repetier, I wanted to experiment with other filaments, but most of these other filaments would not fit in the Da Vinci cartridges. I searched thingiverse and printed sedzen's Spool Holders, which worked, but the...
thingiverse
Although I already had a rack for the filament spools, I didn't have a way to pre-lace the filaments and hold them at the printer. I decided to create this cartridge to fit into the rectangular slot under the original filament grommet. It now holds...
thingiverse
Still working on some of the details, it has a bolt head made into it for a 5/16 bolt, im using a bolt so i can put a one way bearing on the bolt then im making some adapters for some different size spool reel hole sizes to try and help with the...
thingiverse
I loaded my Da Vinci 1.0A printers with the Repetier firmware so that I can use third party filaments. I needed something to keep the filaments from jamming in the edges of the lid. I created this feeder part to snap into the hole on the back of the...
thingiverse
This is a replacement filament guide for a XYZ Da vinci 1.0 that fits between the upper filament tube and the gears (as seen in the second blurry photo). My original piece snapped somehow and whenever I would try to put in filament it wouldn't make...