dart zone pro mk 3 3d models

Malolo's Rpi case is perfect! ... I just added lateral arms to mount it on the left side of a LK4 Pro, and a larger slot for the camera flex cable.

I wanted to add a Raspberry Pi running Octopi (OctoPrint) to run my Ender 3 Pro. It can be see in the pictures in crowser's remade case (<a href="/make:573845">https://www.thingiverse.com/make:573845</a>). I wanted the pi to run off the Ender 3's...

###Ender 3 Pro Filament Out Sensor### **This sensor circuit is based on the 555 Timer IC and will create an oscillating beep (i.e. ...continuous beep beep) when your filament runs out.** **PARTS LIST** (1) 555 Timer IC...

(Description in german below // Deutschsprachige Beschreibung folgt unten)Since I recently mounted a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a...

###Ender 3 Pro Filament Out Sensor### **This sensor circuit is based on the 555 Timer IC and will create an oscillating beep (i.e. ...continuous beep beep) when your filament runs out.** **PARTS LIST** (1) 555 Timer IC...

If yours prints a little too tight, use a bed scraping tool to shave a little bit of the inside edge of the rectangle so the light bar can slide in and out.Notes:Printed on in PLA on its side with no supports, 25% infill, draft mode (0.24mm layer...

This is a re-design of the Creality Ender 3 Pro dual drawer by DWS_Design - https://www.thingiverse.com/thing:3416444 Somehow, the original design didn't fit my printer correctly - one of the bolts on the bottom of the Y-axis wheel kept scraping the...

This project is designed specifically for use with the Creality Ender 3 PRO. It features a triple drawer box that eliminates the need to remove the Y-axis, thereby avoiding the hassle of recalibrating belt tension. The box will remain in place...

This is the result! This design simply fills the space between the original holder and the hole in the reel and was designed to tightly fit around the Ender's pin on the inside and will accept any reel with a hole of 54mm and larger. As my reel is...

This replaces the default spool holder tube/shaft that came with the Creality Ender 3 Pro, specifically designed for use with a Hatchbox PLA 1.75mm Filament spool. There are three parts to print; the Spool Shaft, Hex Nut and Locking Ring. Print...

I remixed that design to fix my Mingda Rock 3 Pro.You will need (2) 608ZZ bearings. I used these the last time I ordered a set. They're cheap and they seem to work ok. (<a...

There are many accessories ready for gopro (which are used by nearly all compatibles), but most of them have 3 drawbacks: cannot be used in other project or cannot be easily modified most of them are concepts, no real print is pictured most of them...

After looking for mounting brackets to relocate my Creality Ender 3 Pro PSU so I could put my printer inside the Creality enclosure, I decided to design my own. I needed brackets to be able to relocate my PSU separately from the printer so it didn't...

This was an effort to eliminate tooling changes between printing and etching on the Ender 3 Pro. This setup creates a screw on mount in place of the provided magnets for attachment. Once completed, this allows you to switch from laser to extruder by...

This is a complete enclosure for the RR V-Core 1.3 Pro. It is designed to use 3mm panels (4mm will work too but will make the lid heavier and therefore you might need a different gas spring). Electronics compartment is sandwiched between the...

MS Surface Pro 3 Tablets frequently overheat when performing complex tasks like 3D editing. This excessive heat can lead to speed issues such as CPU throttling. To prevent my tablet from overheating under pressure, I devised a solution. When docked,...

I made the model to adapt it to the ender 3 or pro. ...not for the ender v2

Hello, As I'm currently in the process of upgrading my Ender 3 Pro to Octoprint, I purchased a Logitech C270 Webcam to use with it. As I wanted a basic, adjustable arm that leaves the V-Slots empty for covers to put in them, and since I didn't...

Update: June 22, 2020 I was designing a Z rod holder (available here: https://www.thingiverse.com/thing:4493376 ) when I discovered that an old bearing from my Ender 3 Pro's wheel fits perfectly in this filament guide as well. The bearing is an 625...

These props are for a DJI mini pro 3. These are version 50 of the prop, so I have replaced the previous model after about 45 more iterations. These shouldn't cause any "ice" warnings that there is too much torque, and they shouldn't over heat if made...

After trying various electronics enclosures for my Ender 3 Pro, I was not happy with many of them due to various issues with each - Fit was tight and not very forgiving for running cables - Airflow/cable management were usually afterthoughts - PSU...

Three railing components specifically designed to work seamlessly with Zone Mortalis platforms, measuring 4mm in width. - A straightforward railing option stands at 48mm in length. - Another version of the railing, featuring some tubing elements,...

Zone Mortalis designed for Vase Mode. Wall and Clloumn must be flipped by 180° before printing. Parts list included for a 48"x48" gaming table. About 1.9kg filament needed. Print settings for Wall and Collumn Vase Mode on Nozzle diameter...

... For further information, see the pictures. This window connects well with the archway: https://cults3d.com/en/3d-model/game/archway-for-zone-mortalis-28mm Suitable glue is required for assembly. ...Sanding may be necessary to make the parts fit.

A barricade for your combat zone. The flaps are hinged for optimized protection. The gate is in two versions, in one block or with two wings. 140 x 50 mm approximately. For smaller printers, a cut version of the gate with support is provided (two...

In this unforgiving environment, scientists and explorers cautiously tread, seeking to unravel the secrets hidden within the Exclusion Zone. Their footsteps disturb the stillness, and the very ground beneath their feet seems to whisper warnings of...

Here is a revised version of the text that maintains the same tone, voice, and phrasing as the original: "Building stairs for zone mortalis requires precision. Print two stair sections and one support to ascend to the next level. The design includes...

Gain knowledge through MK_Reindeer's expertise.

The 3D model in the pictures are from a Creality Ender 3 and have adapted the necessary dimensions for this project to my Creality Ender 3 pro. When removing the support, I always first pierced the edge between the support and the part with the...

... it was a weak point on earlier models. Used 6mm caphead and wingnut on clamp and standard Go pro tripod and 6mmX16mm for fixing the camera to the clamp. I did this to learn "print in place". ... Works great, my son cleans the gutters now.