doc ock funko pop 3d models

This version pops in ~2-2.5 seconds and tends to split in the middle.11/25/2023 Part 1: Shell update. Wall thickness increased 1 more layer to 2.45mm, now 6 extrusion widths. Added the Thunder Devil step rib trying to get the case to fail in that...

Pop rivets are a good alternative to screws here. Printing new parts: Since the ratchet gear mechanism is quite a tiny component with tiny teeth that need to align well, make sure that you compensate for elephants foot in your slicer settings. I...

This is for me problematic because this way I lose the possibility of using the GPIO interface for other purposes (such as enclosure control application) and also I would have many cables popping out of the front control panel. Secondly, I wanted...

I think you can use bigger layer height and bigger nozzle if you want more speedier print. I have used PLA and PET for this but I think you can use whatever material you want.If you would like to have those letters to pop you can do a color...

Create a pop of color with Vase_en_verre, featuring dimensions of 25 x 15 cm. This stunning glass vase boasts an elegant design that is perfect for adding a splash of color and personality to any room. Add a touch of charm with...

These designs are ready to be printed without any problems as they were tested so that no fragile areas remain: *The eyes have been increased in size so that they are not tiny and pop out when rubbing against another object. *Checked the thickness...

This is an electronic die that has built in several dice you can use to play table top games.It includes a coin and die with 4, 6, 8, 10, 12, and 20 sides and able a double 6 sided.It was designed to be used with the parts included in the Alien 3D...

... same size of the metal rectangle. Put the paper into the shoulder part where the metal rectangle was then replace the metal rectangle. Screw back together and test, if still loose, add more paper. Get's the pop and lock back. ... Till All Are One!

Watch me make this thing: https://youtu.be/1ix3x8hLSxQ The diffusers snap into place (or require a bit of cyanoacrylate depending on your tolerances), magnet backers get a dab of cyanoacrylate and pop into the base, and the front plate goes on with...

Alternate turning the top two wing nuts clockwise (top view) until the mouthpiece pops out. Be careful, as they can come out aggressively, and I'm not responsible if any mouthpieces get dented by falling on the floor. Here's a video of me using it:...

Just pop onto the pegboard and insert two M3 screws and then slide the Mount on the holder and enjoy. The mount has pegs 4 inches apart.&nbsp;</p><p>One feature is the small hole on the top that fits 1.75mm filament (use the same color as the print...

... support and it can be removed by fitting a flat razor or thin piece of metal and prying up on the sides... the entire support can be removed in a single piece, requiring very little cleanup. The Bottom Case has prefabbed supports which pop out.

- If you can pry these tabs outwards (using a toothpick, or a tool like this) then there's nothing holding the top housing down anymore and it should just pop up on its own from the force of the spring. However, if your switches are also being held...

I printed with supports on all overhangs over 45*, had to shimmy a putty knife in between support and flat section, pop it a bit on the rounded part of the joint to get it free. 3-10: Added "UP ↑" indicator to CamMount, Body_Cat6, and PiPlate to...

To put the knobs on the #10 bolts I just firmly popped them in, and then used a socket and a C clamp to press on the covers. Because the tightening bolts are so far below the jaws, and just push against the M3 bolt, they tend to bend them...

Also just colored in the lettering with Sharpie to make it pop a bit more. Remixed this from IroesStrongarm's version to offset the QDC holes, widen them a bit so that you can use any panel or bulkhead fittings without needing to thread them into...

3) Pop on the tab protector on the trigger link. 4) Lock in the trigger lever with a 30-60mm pin. Use the spacer provided. 5) Insert the mag release on the bottom of the frame with a spring. Slide in the 35mm pin. Make sure it operates properly...

To do this, you will need to unscrew the smooth rod and pop apart the front/back parts of the base. Remove the upper plate on the right side, as well as the right plate. These will no longer be needed! After filing, carefully place the new motor...

How I Designed This Pro/Con Pro: Easy to remove window, just pop off the corner clamps and window is free. No modifications to QIDI chassis are necessary. Re-use original M4 mounting screws. Con: Needs 6mm dia x 1.5mm or 3mm neodymium magnets. I do...

To make extracting them easier, I designed a simple plunger mechanism with a small cam that pops up automatically when you insert the card, then all you need to do is push down on it and out comes the card! Easy to assemble too - stack as many slots...

The chords seemed to do the best.I was able to use a drill bit to pop a hole to the center and insert the tube. I was able to get the doors on the trap to lift halfway with this printing style. ...I may try to put artificial infill into one of the...

Check that the buttons now "pop" when pressed **and** when released. 4. Install the DC power jack, switch, and banana jacks. 5. Wiring: Use a fairly high-powered iron (GND plane and beefy bananas can suck the heat away before the temp gets high...

This may not work for everyone as I mount my lcd screen on top of one of the towers (simple to do just open the case and flip the screen over and pop their lcd bracket on to the tower) I much prefer this location and angle for the screen as it does...

Use this to turn arduino pro micro or leonardo into a joystick/HID device https://github.com/MHeironimus/ArduinoJoystickLibrary I used this Arduino sketch https://www.tinkerboy.xyz/arduino-usb-gamepad/ I used these rotary encoders...

### Using the adaptor ### Pop out the lenses from your Zenni frames (see this video: https://youtu.be/rB6568bjAlw?t=39). It might take a bit of force, but if you have clean hands they shouldn't get scratched. Then align each lens from the top of...

hyperpixel : https://shop.pimoroni.com/products/hyperpixel-4-square?variant=30138251444307 pi zero headers: https://shop.pimoroni.com/products/gpio-hammer-header?variant=35643241098 usb 2.0 hub (you'll want to pop it out of its plastic shell):...

... filament - PETG at a minimum - using at least 60% infill and support so that the bottom lip prints correctly. I tend to print these with a full raft although that's up to you and your printer. When I do the support pops right off with it. ...

We decided that the correct approach was to design a system where one door would be pushed in, causing the other door to pop out enough to allow users to grasp finger grooves on the side of the panel and open the door. This requirement presented a...

Just pop the spring out of it's 'seat' at the bottom of the magazine, slide the stock baseplate off and the new one on, and let the spring snap back in place. <h3>Printing Notes:</h3> <h3>Magwell:</h3> 1. 95-100% infill recommended 2. Supports...

Pop the new door with the power button into place. This door/mod has only been tested on the Fatshark Dominator series of goggles. This includes the HDO's, HD3's, HD2's, and V3's. Try at your own risk! Mixing up wires definitely has the...