draft 3d printing

PROTOTYPE TESTING REVEALED JOINT STIFFNESS, LEADING TO A REFINEMENT OF PRINT SETTINGS. LOWER ARM SECTION INCOMPLETE, BUT ALMOST FINALIZED WITH THE ADDITION OF Wrist ROTATION PARTS AND MOTOR MOUNTS. UPDATE 02/02/2016: VERSION UPDATE FOR THE HAND...

Each DB25 connector is fixed onto its printed bracket using 4-40 screws coupled with complementary nuts. ... As a final touch, I fashioned an extensive 25-conductor ribbon cable approximately twenty centimeters long with crimp-on DB25 fittings,...

You'll need to use a preferred set of ducts from one of my related designs - links are provided below: https://www.thingiverse.com/thing:3774121 https://www.thingiverse.com/thing:3881061/files I printed these parts with Prima Select Light Blue PETG,...

 My printer apparently does not have as good a printing tolerances, so I changed the threading from M6 to M8 and a few other changes and enhancements.  I added different tolerance options for the threading, made the threads go all the way thru the...

I'm not a Necron player, but if you use this in your army, or just print it, I'd love to see photos! The Fluff Setekh was crafted as one of the greatest creations of the Necrontyr. During ancient times, its purpose was to bring death to every...

Regular PLA can be annealed but it shrinks significantly more and may not fit without printing a larger part first. The PLA+ part is now holding up to heat exposure. To anneal the part, a large pot was heated on the stove, and aluminum foil was...

As evidence of its functionality and robustness, I have created a printed circuit board based on the settings specified by Synthetos documentation; however, for expediency I resorted to finding solutions that circumvented certain documentation...

We only needed to print one bottom mold, either a blank or heart-shaped design. I made sure to keep the parts loose to prevent any binding issues caused by the gritty mixture. The necessary ingredients included citric acid, cornstarch, and essential...

I printed mine using MakerGeeks PETG, but next time, I'll probably use PLA and then subject it to 80C for 40 minutes. Unfortunately, PETG didn't hold up as well as I had hoped under high temperatures. In addition to this jig setup, here are my...

If you wish to contribute, visit my "Cults3d" profile at https://cults3d.com/en/users/Trystan for details.\n*More pictures coming soon!\nTo create this rocket, also obtain the following materials: \n1x 18" Nylon Parachute from allrocketengines.ca...

...I simply paused the print, changed filament and resumed, works pretty nice dont you think?! _________________________________________________________________________ Simple DIY Powerbank build. ( Measurment 140x73x16) Pretty funny story.

**Building Instructions:** All printed components are ready for assembly, apart from a few specific parts that may require additional sanding or drilling: 1. Aileron (Seitenruder) 2. Motor Holder 3. Servo Link (Servo Hebel) 4. Body...

... on the real wheel. FOR PERSONAL USE ONLY - NON COMMERCIAL - NOT FOR RESALE COPYRIGHT Canary Sim Wheel Designs - ALL RIGHTS RESERVED You cannot sell the digital model, a derivative or adaptation of the model, nor can you sell prints of the model.

Print the two pieces. 1. Get some white, slightly stretchy cloth. 1. Stretch the cloth over one half. 1. Press the other half on top of the stretched cloth. 1. Optionally trim the stretched cloth (though if you trim too much, it might make it...

Print at 100% infill for maximum toughness. This copter weighs about 6g. I use 380mAh batteries, which give me around 4 minutes of airtime. You can check out the flight control board here:...

To get started, you need to print both the front and back frames. Once they're ready, carefully take a look inside and measure the perfect viewing angle for your eyes. From there, choose the correct length of the middle frame based on its filename. A...

http://www.thingiverse.com/apps/customizer/run?thing_id=56795 Instructions Using the following options: safe_pin_xoffset = [0,cylinder_pin_offset,cylinder_pin_offset,0,0,-cylinder_pin_offset,-cylinder_pin_offset,0] polygon_count = 32 keycutcode =...

You may want to consider changing colors halfway through printing the tiles so that their orientation can be easily identified. Six 8 x 1mm magnets can be glued into place to hold the lid securely onto the base of the container. <font...

http://www.thingiverse.com/apps/customizer/run?thing_id=56795 Instructions Using the following options: safe_pin_yoffset = [0,0,0,-cylinder_pin_offset,-cylinder_pin_offset,0,0,cylinder_pin_offset] type_of_key = 0 pinstepheight = [...

Smaller printers may need to print sections separately. The design requires supports for all parts except the lower hull, skirt ring, and skirt clips. I've tested its capabilities and strength by flying it extensively, flipping it multiple times on...

Now that you have your printed components ready, let's move on to the assembly process: First, lightly sand the edges of the arms where they fit into the body. Then, place the nuts at the bottom of the middle body using soldering. You can opt for...

Its a bit of overkill as the wire stays in place well by itself but I like belt and braces :D Printing is easy. No supports required. PLA works fine but if you are going to leave this antenna in sunlight for any period of time I would recommend...

Print Settings Printer Brand: TEVO Printer: Tarantula Supports: No Resolution: 0.2mm Infill: 13% How I Designed This Since I've been playing around with FreeCAD, I decided that this would be a good test of my abilities (or lack there off). Never one...

The cap fits on the lens shade, not on the “naked” objective.If you want to print these, keep in mind:1. A soft material must be used, meaning you will have to use TPU.<br>2. The material should have a matt/dull surface which means that most kinds of...

The L brackets have been tweaked (slightly taller with printed threads) from the original design so that common 500mm length carbon fiber tubing (12mm OD -10mm ID) can be used without any issues. The 6mm threads were added over the original design...

Then enter the following command.\r\n\r\nM851 Z-0.9\r\nM502\r\n\r\nSave the memory or enter that value in Marlin and you're done.\r\n\r\nI recommend enabling babystepping, especially when printing various materials. For example, nylon requires...

Additional set for RS-CNC: https://www.thingiverse.com/thing:3010914 These are the parts I drew to accomplish: - Remove electronics from inside of RS-CNC - Make two original parts stronger 1) Facade Addon - Add a switch for light on/off - Add a...

Used PETGScrews required.6G x 12mm Sheet metal tappers - For the Interface bracket.Flie the tip off the screw, about 1mm or less, to make it a little...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: No Supports: No Infill: 20% How I Designed This At the bottom we have two moons: one visible and its dark side used solely for supporting the rotating disk above. The pole...

Here is a TPU spacer to be used to install the really nice HEPA & Carbon Filter designed by PrinterBox [ https://www.printer-box.com/hepa-carbon-filter ] on the marvelous [Prusa] Box also from the same designer [...