drafting pencil sharpener 3d models

The base 3mf files include draft shields that I found provided the best protection against corner warping on the PETG. (4 will fit on a standard size print bed, but at the volume, they are much more likely to warp at the outside corners. I settled on...

The first draft of Clip is now attached along with its matching 123D Design file. I'll need to confirm whether it mingles properly with collar and vial's rear half, plus I'm uncertain regarding the 5mm thickness. P.S. I've previously announced my...

In addition, the 9v battery was a super tight fit, so I enlarged that space slightly.\r\n\r\nI imported the DomesticHacks .STL files into F360 and re-drafted some of the parts to add 0.25mm clearance on the battery door. I also trimmed the height of...

I installed brass inserts but it should also self tap the screws if needed To hold the lid on: M3 screws and brass inserts. To hold the TFT on M3 screws come in from the top and are held to the TFT35 via a nut I included the Fusion 360 file so feel...

This lobs the dart about as hard as you would throw them by hand. The crossbow I based this off of can be found here on amazon: http://amzn.com/B07DMQGZB7 And the darts pictured can be found here: http://amzn.com/B003K0LWR2 I printed this on a stock...

Update 2022 03 11 Uploaded an assembled draft 3d file for the easier understanding Update 2022 03 01 Filament cutter settings description and suggested nozzle drill size is now 1.7mm Update 2022 02 28 Expanded version for 102x76 mount for some mks,...

It tucks the hotend fan under the extruder motor, helping to cool that motor AND push the air harmlessly to the left without the same likelihood that it will draft onto the build plate that is evident in all other designs I've tried (and that's most...

The hardest part was drafting up the parts, aside from print time (approximately 24 hours). I'm thrilled with how it turned out! I used PLA, and while I've tested some with PETG, I still need to improve my skills with it. Edit: I added...

There are some some surfaces that push the boundaries of draft angles but these are inherent of the original prusa design parts and not of choosing or design. The test print so far IMHO are much improved and both my water nozzle tests and the Sim...

The settings used were 200 microns, hollow fill, and line pattern (the default draft part setting). Despite this, the result is quite precise and fit together well without any trouble. Post-Printing: Finish Parts - Smoothing and Fasteners After...

... This I designed the files by using the original instruction and layout cards from the kit. I drafted the parts on SolidWorks and then fine-tuned and modified them as necessary. ... Future versions may be thinner in some areas to reduce weight.

Within real-time collaborative development projects utilizing solid computer-based drafting techniques, the CAD/CAM/CAE tools built into software engineering platforms such as SOLIDWORKS streamline production processes for developers, reducing...

Only the gun from the original model remains the same.Printed with 0.3mm Draft mode, PLA, on MK3S. It should work on Mini, MK4, or XL with no problem.I also experimented with Organic Supports & make recommendations for the best way that I found to...

It's a first draft, and nearly all the printed parts were used without iteration after seeing how they fit together. It came out pretty well, but there are many things I would redesign if I were doing it from scratch now. The main gear ring does...

If they don't touch when it is closed, they may not hold it together.I used PETG so that it (probably) won't melt in my car on a hot Summer day, but I am also including the gcode for ASA (with an embedded draft shield) too, in case you live in really...

New* Updated release to include a revised extruder design (original is still there too!) a 2 piece printable bed, updated build guide, and the first draft of a getting started guide. Enjoy! Introducing the mapleMaker Mini V2 3D Printer The...

Step 6: Edit and Proofread Once you've completed the first draft of your assignment, it's time to edit and proofread. This is where you refine your work, eliminate any errors, and make sure everything flows smoothly. Take your time, read carefully,...

I recovered all broken parts, made measurements, and quickly drafted a close copy in SketchUp 8. I anticipated several revisions but knew I had a good starting point. The printed part worked first time once supports were removed. However, holding...

ATTENTION: Pieces are still unprinted and not tested.... V2.0.0 - License May 17, 2020 Fixations of the heated bed to the 2020 profile structure were added. Metadata of the "CoreXY_V2_St.FCStd" file was modified to attribute it a Creative Commons -...

Sorry for the less-than stellar print, it was done in draft mode just to prove function. Both .stl and .obj files included, because I can, and because .obj is a better format which doesn't force everything into tessellations (i.e., curves are...

Draft drawings for a compression tool are included, for automatic compression and ejection of the brick. The compression tool & heaters I installed inside my mould can all be run on 3D printer hardware, using basic gcode. The Nema34 I'm including in...

I'm including a superfast plate based on CNC Kitchen video "FASTER 3D printing of face shields" refer to the Prusa material compatibility and disinfection info at:...

I think its helping to direct the exhaust and prevents it from creating a slight draft around the work area, but I thing I get more distance from the inlet when it is installed. Other possibilities are to hook the box up to a larger fan via a duct...

setup is very dependent on how good belts are installed Draft BOM: - GT2 belt 5m - 20x bearings F695-2RS - GT2 Pulley 20 Teeth 5mm bore 6mm - 2 extension cables for motors - set of nuts and bolts for m3/m4/m5 - the length and count for each to be...

This should include 2D and 3D drafts before printing. Once a model has been successfully printed, the group should work on initial product line order, projected supply and demand, packaging aesthetics, and even marketing. Advanced lessons can...

Sorry for the less-than stellar print, it was done in draft mode just to prove function. Both .stl and .obj files included, because I can, and because .obj is a better format which doesn't force everything into tessellations (i.e., curves are...

Version 2 (v2) has better layer height options on the print settings tab: - 0.3mm draft v2 - 0.3mm v2 - 0.3mm speed v2 - 0.2mm quality v2 - 0.2mm speed v2 - 0.15mm quality v2 Normally, the first layer speed is 25mm/s, but with speed settings it's...

They choose a type of cell to create, make a drawn draft, and ensure it has the correct shape, physical features, and proportions. Duration of Lesson After students learned about the cell unit in class, the actual 3D modeling and creating part took...

I printed this design using my Creality Ender 3 with Amazon brand green PLA and the default 2 mm draft profile in Cura. The top plate is quite long at 285 mm, but it fit perfectly on my printer when rotated 45 degrees on the bed and the skirt was...

I started with some basic gear ratio calculations, and had a flashback to high school and college drafting classes, while I researched bevel gear designs. Online gear design tools are way better than doing them by hand back in the old days. After...