drake modeling

Depending on the power supply to your printer you may need a step down voltage regulator, pre built versions of which can be found on eBay or Amazon, or you can have a go at deriving a 5V supply yourself with a linear voltage regulator or go all...

READ THE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING TO MAKE SURE YOU'RE COMFORTABLE WITH THE PLANS LAID OUT...

Diameter is maximized over stock to reduce clearance in pump, increasing efficiency.*I guessed on this one, I'm not a prop/impeller designer so I could be way off and I don't have test data to determine if performance is improved, but pretty sure it...

... mount and two each side for accessory mounts. I used one on the right for strain relief for E3D wires, 2 on left for fan mount. 4 on side fan, only two are used depending on fan model. ...2 on cable chain attachment to attach it to extruder mount.

After render the model in OpenSCAD, generate a .stl file and bring it to your 3d printer. Print the mold with either PLA, PLA+, or your favorite filament. 1>Use the 3d-printed male mold (without flange) as a template, cut multiple blades out of...

Anyways, this is getting out of hand so here's the important stuff: Many models to choose from! 18mm sensor 12mm sensor 8mm sensor Then choose you cap: 2 stock fans with chain mount 2 stock fans no chain mount No fans no chain mount No...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

I might get to that soon). Vitamins9 M2x12 socket cap machine screws1 M2 hex nut1 6700-2RS bearing (the model could be modified to use standard 608 bearings) Assembly instructionsStart with a handle, spring, spring retainer, and 1 of the M2...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

... 3D model created using SketchUp Make (free software). I also tried 45 degrees, but the fan's thickness made it touch the desk surface below, so it had to be skooted up to the high end of the stand... thus the cooling effect would be diminished.

Wheels to axle : M3 leafspring to axle : M1.4 Leaf spring brackets assembly : M2 Leaf spring to bracket : M2 end of stab leg : M2.5 Female ball joint adjustment M2,5 flat ramp bracket on ramp and on trailer : M1.4 stab legs on brackets : M2 Rims...

I used hinges from model aircraft stores as they were the perfect size. The battery holder can accommodate a Turnigy Nano Tech 3s 2.5amp battery and fits over the support bars on the bottom of the box. Trailer Under runners and boxes: The runners...

--------------------------------------------------------------------------------- Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support...

This is a 1:50 scale model (metric) of a space rocket that transforms into a Mars base. (well, conceptually) Instead of building vehicles to transport pieces to build a base, it seemed more reasonable to use the whole spaceship as the future...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Entry point for USB wire, hole has a separate part for covering it: + usb_wire_cover - base_bracket2_corner_RH x1 - base_bracket2_corner_RH_back x1 - base_cover_big x2 - base_cover_small x3 - base_cover_corner x2 * Front covers: base model is...

The cookie cutter designs are partly based on 3D models from our [3D museum](http://sketchfab.com/NHMWien) and were designed by Viola Winkler. The scan team of the NHM Vienna wishes you a wonderful holiday season, lots of fun baking cookies and a...

Wheels to axle : M3 leafspring to axle : M1.4 Leaf spring brackets assembly : M2 Leaf spring to bracket : M2 end of stab leg : M2.5 Female ball joint adjustment M2.5 flat ramp bracket on ramp and on trailer : M1.4 stab legs on brackets : M2 Rims...

- Make sure you tune the voltage if adding TMC drivers, such as with voltages specified for your model at the [Tuning & Upgrading the Stepper Drivers](https://jgaurorawiki.com/a5/stepper-drivers) article at the Unofficial JGAURORA Wiki. Use whatever...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

... The models are in the position, they should be printed. No support is needed. I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this tall piece. Printed on an Ender 3 Have fun!

License ------- The "Crystal Generator" models (.stl) are licensed under the [CC BY](https://creativecommons.org/licenses/by/4.0/) license by [Code and Make](https://codeandmake.com/). The "Crystal Generator" code (.scad) is licensed under [The...

The model formed in our minds is based on what we see, and the brain completes the rest, including hidden features. So, I set off to design the object using Fusion360 and test it. I created several versions of the lock inside the object, but this one...

I didn't even try to 3D model anything because of the sheer size of the base plate, so I cut it out of foamcore. But it could just as well have been the minis sorted into bags instead. The tray is sized at 240x397x56mm externally. If you do paint...

Tools Hex wrench 2mm and Mmm...

You could also use hex stock cut to the same size, which would increase the weight (since the center of the nuts is hollow) and improve the spin time, but also increases the amount of work that needs to be done in order to build these.The nuts must...

0.2mm tolerance for sliding parts Verified to Print well at 100% and 150% sizes (0.4mm nozzle, 0.2mm layer height) My Colors for each .stl model Gold - Gold Tool - Gold Diamond_T7 - Blue Bolt - White Barrel - White BarrelSpring - White BarrelPinV2 -...

Both versions comes with an extra split in half model, depending on your print preferences. If you glue a cow to the ground plate as prop, remember to place it where the UFO won't crash on it's head…</p><p>&nbsp;</p><p><strong>My UFO doesn't crash...

I won't go into any more detail because it involves mains wiring and if you're legitimately comfortable with mains you should be able to easily wire it up any way you please. The cover has melted/pressed in brass M3 Threadletts for durability. The...

Please note the Modular Assembly Preview STL is just to show a preview of one assembly model, not for printing. Here's a brief description of the types of parts included. Cuffs - Number is the inside diameter of the cuff. Diameters include...