elektron stand 3d models
153174 3d models found related to elektron stand.thingiverse
This simple stand will hold your Elektron Digitakt, Digitone or Syntakt at a much more comfortable angle (13°) than flat on your desk. Includes the Elektron logo on the back edge. This is narrow enough to fit between the feet on the Elektron itself.
thingiverse
This is an ELEKTRON stand with a nice text on the side. It can be printed directly using the supplied STL File on the anycubic photon without any supports or rafts. If you want to print it on a FDM Printer you can stretch it to make it a little...
thingiverse
Stand for Elektron machines. 65 degree angle 30mm space between table surface and machine (to run cables under if you have a device infront) Important to note: 1. This model is not for the MK1 versions of ANALOG4 or RYTM, as those have...
thingiverse
Stand for Elektron machines. 65 degree angle. 9,6mm thick. Comes in three versions. See photos. Important to note: 1. Recommended screws; M3x10 (M3x12 is fine too). Longer screws risk damaging the PCB inside the unit. 2. Not recommended...
thingiverse
Stand for Elektron machines. 65 degree angle. 9,6mm thick Has a 30mm space between table surface and unit (good for running cables under if you have a device infront) Comes in three versions. See photos. Important to note: 1. Longer...
prusaprinters
These are the components to build a triple or double Elektron gear stand. For the triple stand it supports a Digitakt, Digitone, Octatrack combination. You can also fit four boxes the size of a Digitakt or Digitone.You connect the side panels with...
thingiverse
This is a Elektron stand for the Digitone and Digitakt combo. It's robust, I printed it with 15% infill, 2 perimeters. 0.2 layer height, printed with black Prusament PLA. I used M4 bold and nuts to attach the components together. There are...
prusaprinters
This will create a vertical stand for your Elektron Digitakt and Elektron Digitone combo. They are stacked vertically with this stand. Each printed as separate components and attached by M4 bold and nuts.</p><p>Required components to print:</p><p>4 x...
thingiverse
Adjustable stand for Elektron Octatrack, 0-30 degrees viewing angle. Instructions Illustrator file is ready for submission to RazorLab/Ponoko. Please note, the cutouts for screw mounting are fairly...
thingiverse
... could very well be the PETG. Also I included the full and uncutted stand, as well as the blank back plate. ... Edit: The side panels are now having 0.2mm more clearance on the pin holes, so that fitting them should no longer require as much work.
prusaprinters
<p>No Supports Needed</p><p>4 - 5 Wall count to ensure strength </p><p>10% Infill</p><p>Bolts Size: M3</p><figure class="image"><img...
thingiverse
Vertical multi-stand to come eventually. You can print these in - single-device configuration with "slim" side plates (5mm); this is not really recommended because it is slightly less robust, but might be preferrable if you're really low on space...
thingiverse
Minimal Stand for Model:Cycles or Model:Samples by Elektron. ...Designed for a small print area.
thingiverse
Print two to make an angled stand for your Elektron musical instrument! I wanted a plain stand for my Octatrack so I just made one. It will probably fit the Analog Four, Monomachine and Analog Rytm too. ...Enjoy!
cgtrader
Digitakt 3d model of sampling drum machine from Elektron. created in blender. texturing done with substance painter and affinity designer. 4k pbr textures included. material setup inside blender for eevee and cycles, 37530 polygons all quads. ...
thingiverse
Cover for the Elektron Digitakt. Six neodymium magnets 5mm x 1mm can be glued in to keep the cover in place for transport. The magnets sit on top of the screws so the cover does not scratch the front plate. ...
cgstudio
Old SSSR TV model name "Elektron 714".________________________The files:- Elektron714.max- Elektron714.fbx- Prev.jpg- DerevoPered.jpg- DerevoPeredBump.jpg- Kineskop.jpg-...
thingiverse
... onto a 220mm wide bed. ... This print was broad enough to start warping, even with PETG, however it didn't affect the outcome enough to matter. The channel is so a strap can be used. This fits into Elektron's carry bag for 2x Digi's really well.
sketchfab
Model updated for 2021 Improved textures, improved LODs Insipred by Elektron 380D Additional file contains manually made LODs in 4 stages and custom collider in .fbx, .gltf and .obj formats as well as 2x4K (clean and dirty) texture sets for Unity5,...
sketchfab
Model updated for 2021 Improved textures, improved LODs Insipred by Elektron 380D Additional file contains manually made LODs in 4 stages and custom collider in .fbx, .gltf and .obj formats as well as 2x4K (clean and dirty) texture sets for Unity5,...
thingiverse
This is a DIY version of Elektron's as-yet-unreleased battery handle for Model:Cycles and Model:Samples. It is designed to hold any "lipstick" sized USB phone battery bank, such as the [Anker Powercore+...
thingiverse
3S2P 18650 holder for Elektron Digitakt drum computer. Holds 6 18650 batteries and a small BMS, screws into the VESA holes from the inside. Alternative to using 21700 cells as this can get you about 7000mah (2x 3500) compared to the max 5000mah from...
thingiverse
- Added two circular indents in the middle to accommodate the middle two screw heads on the Elektron -takt devices. I just printed 2 of them and super-glued them together. ... Time permitting, I may add joints to the top/sides so that the two halves...
thingiverse
This is a simple and easy to install remedy for numb pads of the Elektron Model:Cycles and Model:Samples grooveboxes. The inserts create a pre-tension between Velostat-coated foil and carbon traces on the PCB, which reduces the amount of force needed...
prusaprinters
<p>A 2mm thick cover for the Digitakt (it probably fits the Digitone as well).</p> <p>It can be kept in place with a strap.</p> <p>I personaly use it with a amazonbasics gopro bag (L) : <a...