element 3d models pack

Previous model description: I hooked up a 1400mah battery and drove this home from my local park around 500-600 meters with no heat issues affecting the PLA print. I have used this around the house quite a bit with the camera, and it works well. The...

(I used bodies instead of components to avoid model breakage in case of major size change.) Required Parts list and where I got them: 1X 2032 battery holders: https://www.amazon.ca/gp/product/B08SQRSTJ4 1X rechargeable LIR2032:...

I already had some Koss Porta Pros so I printed it and used that for a couple of weeks (after tweaking the size of some parts for a tighter fit, especially the push pin which is/was modelled too small). However, after a couple of weeks using that,...

Licensed models were manufactured in Germany, Sweden and Russia First Fighter The Type L is famous for being used by Roland Garros to shoot down three German aircraft in April of 1915. This was a special single-seat arrangement made for the tennis...

This model only cost 1 dollar because I am only pricing the topper and Star mount, the rest is free with the purchase. This is a pixel tree mount to build an eighteen string 216 degree pixels tree. Height can be up to 5 feet. The base design is...

You could also use hex stock cut to the same size, which would increase the weight (since the center of the nuts is hollow) and improve the spin time, but also increases the amount of work that needs to be done in order to build these.The nuts must...

I've updated the model with the Orbiter Ver. 1.5 as I purchased another one (I don't want to take the one I'm using on my Bear off as it works soooo good). I've also updated the filament sensor to use the Prusa MK3+ sensor as I have two of them. I've...

** FUSION360 and STEP Sources are included **** I have my printer into an enclosure and, to save the electronics from excessive heat, I've designed this model to enclose all the electronics at a singe location. These were my requirements: -...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would definitely...

It is possible that a future will make and upload a model of that piece. In the meantime, if anyone knows where to get suitable pads, please let me know. As I was saying, I started to hang them on the screw. Since the surface of the screw with the...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale]   A vanguard of the Duke’s Army that was initially sent to quell the outbreak. A thousand men were torn apart within an hour of arriving in Canos’ south side, leaving...

After studying what was available, I started modeling my own. The problem was that most of the projects were on console tables, but our table is held on two rails, one on each side. Initially, the project was implemented on a seven-string polispast,...

*** UPDATE 30/06/2021 *** As lots of people have noticed, the original model is a ridiculous reducer at a ratio of about 3:1 from the original duct. I've now added a design that is much larger (labelled as "Full Size") and can be printed in three...

Research I found two suitable models on Thingiverse which I thought could be easily enough modified: Tweezers for SMD by Ruslan_Kulibin SMD Test clamp by Tom20170 which I both printed yesterday. They are both quite nice designs, I especially like...

The assembly of the upper part of the buffer is clearly described in Dave's files (please visit his thing on the Thingiverse (link above) and download the PDF file with the instructions or click the direct link ). Hardware needed for the base part...

Just make sure to get the alignment correct before letting the glue set up!Notes:Raft:              YesSupports:    NoI've had the best luck printing these using a single-layer raft, with the part oriented...

    Approximate Dimensions (LxWxH): 6'x4' when all pieces are used Rocky Valley and Cliffmont - each (9) Large Tiles  (8" x 8") - 24" x 24"   Dornan's Hill and Twin Ridge - each (4) Large Tiles  (8" x 8") - 16" x 16" Rumble Downs - (3) Large Tiles...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! :) Update 1: My Start and End G-codes in Cura working well with this...

now you can the stands/feet print without support or if you want the texture of the powder-coated pei sheet you can print it on its side without support.Release Candidate 1.5 - 15 January 2021Updated some sections to the model so it's stronger when...

This was my first prototype, there are always rooms for improvements….I am afraid this cannot be print on a Mini+:(The biggest model is 188.90 (X) by 202.60 (Y)I have been looking for raised pet bowls that looked nice and highly customized without...

I have printed all of the parts and assembled a model which is shown. The "Dome" cover will fit over the Base Plate, and in turn a 1/2" piece of sprinkler pipe will fit over the tabs in the center of the Base Plate. The Mic Holder will fit over a Gen...

Used PLA, but as mentioned in the comments, PETG is probably a better choice for the gears. Print 3x '19-screwFront01' Print 6x '22-screwBack01' Change the filament color before the last 3-4 layers for part '05-frontHolder02' to see the text (or...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: The Sightless Seer] Known among many of his comrades as Byrè-Myn Fyreth, One-Man Army. Zyril is infamous for his single hold out in the town of Tara when...

being able to reprint the broken part vs the entire model is a plus. Except for the charging ports, no glue is needed. All the STL files have been positioned to hide the seam as much as possible (when possible). The Activator Assembly parts are...

After studying what was available, I started modeling my own. The problem was that most of the projects were on console tables, but our table is held on two rails, one on each side. Initially, the project was implemented on a seven-string polispast,...

Printer Settings: * Printer Brand: RepRap * Printer Model: Original Prusa i3 * Rafts: No * Supports: No * Resolution: 0.2mm * Infill Percentage: 25% Print Notes: I utilized a 0.8mm nozzle to expedite the printing process, which took approximately...

That link also calls for using alanho's file to hold the TFT50, here is a direct link to his page as well: https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/alanho/BTT_PITFT50_v2_Mount I also made some simple changes such that it...

As I'm new to parametric modeling, this solution was done without adhering to full parametric techniques. I'm still learning. The KeyAll HV has two mounting holes, which left 2 open feet for other uses. One foot was left unused, and the other to...

This model fits seat shafts with a 16-groove, skip-tooth-top, 12mm nominal shaft: (note skipped groove, blue arrow) Probably best to print these with the spud pointed up for minimizing how much trouble the overhangs inside the hole will...

Once I get the sizes right, I'll upload the fixed models. <b>23/03/2020</b> (3) Just uploaded some slightly altered versions in an attempt to use them as actual particulate filter masks. The new versions have a single vent hole which hopefully will...