grabcad
MI5100 5MP USB CAMERA MODULE USB2.0 APTINA 1/2.5INCH COLOR CMOS SENSOR 100DEGREE LENS
thingiverse
2) The 2.5mm screws (and holes) means that the threaded PCB board of the camera also attaches to the screws. This makes it difficult to get a nice, clean closure. 3) The screws aren't indented, sticking out ugly in the back. 4) This thing gets...
grabcad
This is the 3D printed camera mount we used in the 2019 FRC season. ...It's designed to be used with this camera https://amzn.to/2L4SiDoELP 170degree Fisheye Wide Angle VGA USB Camera Module
thingiverse
ELP camera mount adapted for the currenttly available USB camera from ELP: https://www.aliexpress.com/item/32711091946.html I think must fit most of ELP camera modules. ... Tinkercad project: https://www.tinkercad.com/things/bz0mG9ZWIfP-elp-mount
thingiverse
This is a camera that is made from the standard USB Camera Module (such as ELP) but it has a hole prepared to accept a standard 12mm lens. To use the camera module you have to remove any other lens holder. You will also need to tap the plastic with...
thingiverse
Camera Case for ELP 720p 120fps USB Camera (https://www.amazon.com/gp/product/B07DWXRKNL)
thingiverse
Case for the **ELP** USB HIGH SPEED USB CAMERA WITH 170 DEGREE FISHEYE LENS (Model **ELP-USBFHD01M-L170**) **Camera link:** http://www.elpcctv.com/linux-hd-1080p-high-speed-usb-camera-with-170-degree-fisheye-lens-p-82.html **Note:** - Use M3 nuts and...
thingiverse
This is a camera case I made for an ELP lowlight camera module I use with my octopi set-up. ...The case can be mounted on a tripod an allows the camera to be tilted up and down.
thingiverse
This is a housing to mount a USB camera module to a piece of VEX VersaFrame stock. This design does make the camera upside down but that was easily fixed through the software. The holes are designed for #8-32 machine screws. The wires attached to the...
thingiverse
This is a camera mount for a 0.3-megapixel camera. It can attach to a 10mm rod and works with the Stand, Clamps and Equipment Kit that I have made. ...Find that system here, https://www.thingiverse.com/thing:2765367 <h2>Keep up to date</h2> New...
grabcad
This is a mockup of the standard camera board module that you can get almost anywhere. The lens arrangements change depending on the board but the basic board layout is consistent.Some boards have a second connector on the back but not mine. I didn't...
thingiverse
Two part case for the "ELP 1.3megapixel Day&night USB Video Conference Camera Usb Camera Module". ... https://www.amazon.com/dp/B00SPBCZL8
prusaprinters
Two part case for the "ELP 1.3megapixel Day&night USB Video Conference Camera Usb Camera Module". https://www.amazon.com/dp/B00SPBCZL8 How I Designed This Modeled in SketchUp Make 2017 (SKP file attached). Category: Camera
thingiverse
Hey :) Here is a very simple housing for a USB CMOS Camera Module. ...These modules can be found in notebooks.
grabcad
Camera Module FHD USBFH01M USB 4-pin Frame PCB 38 x38 Camera PCB 32x32 PCM mount 2mm Lense 180 degree fisheye
thingiverse
I have made a case and mounts for a the ELP-USB3MP01H-L29 3.0 Megapixel USB Camera. These mounts are also designed to work with foxel's ELP USB Camera 8M camera enclosure. The cases are not interchangeable however. Mount 1.4-20 Thread.stl is...
thingiverse
Quick and simple clip on mount for a bare bones USB ELP Camera. Minimal-ish design to print reasonable quickly (around one hour for me), also to allow adequate cooling at higher frame rates. No supports needed. I printed mine in PLA, but I...
thingiverse
With webcams (the good brands/models) becoming harder to find, you are seeing these USB Module Cameras popup more now on places like Amazon. Some of them come with enclosure and all, but not all of them. Some of them are just circuit boards with a...
prusaprinters
Housing and Telescope Mounts for Camera Module Intended Purpose These parts are designed to work with a 38x38mm USB UVC Camera module such as those from Arducam or available online from various Asia based sellers. A camera module assembled with the...
thingiverse
# Housing and Telescope Mounts for Camera Module ## Intended Purpose These parts are designed to work with a 38x38mm USB UVC Camera module such as those from Arducam or available online from various Asia based sellers. A camera module assembled with...
thingiverse
This is a nice simple case for an ELP 8MP or similar camera module. I created this to help me take time-lapse of my 3D printer in action. It features a standard 1/4 20 screw mount so will easily go on a tripod or go-pro type mount. I included the...
grabcad
... is a missing design I created for the Sony IMX179 UVC USB 2 PCB module. Its exactly modeled off the WaveShare version.https://www.waveshare.com/imx179-8mp-usb-camera-a.htmThis is a typical form factor though so may be helpful elsewhere.
prusaprinters
Actually it is drawn from scratch. Details are in the file. Made of 3mm acrylic, the knob is made of 10mm acrylic You also need 4 screws, nuts and washers m3 (12mm) 3 screws and nuts M2 (12mm) 1 screw M5 (20mm) 1 threaded insert (M5) It is made for...
cults3d
Made of 3mm acrylic, the knob is made of 10mm acrylic You also need 4 screws, nuts and washers m3 (12mm) 3 screws and nuts M2 (12mm) 1 screw M5 (20mm) 1 threaded insert (M5) It is made for the 8MP lightburn camera module but should fit any module...
thingiverse
Made of 3mm acrylic, the knob is made of 10mm acrylic You also need 4 screws, nuts and washers m3 (12mm) 3 screws and nuts M2 (12mm) 1 screw M5 (20mm) 1 threaded insert (M5) It is made for the 8MP lightburn camera module but should fit any module...