emerald 3d model

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

The hole for the cable tip should be wide enough for any similar cables, but if not you can pretty easily remix the model by just cutting the hole to be larger or adding material where needed. I suggest printing the dock upside down and including...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

I created this VW Passat B8 phone tray because my iPhone 8 with cover didn't fit into the standard one. Rotating the USB port by 90° it has space for phones with a length of up to about 15 cm which is about 11mm more than the standard tray offers....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_top_outer_edge_chamfer_radius = .6 stencil_vertical_position = 50 use_mouse_ears = 0 custom_back_camera_x_size = 20...

The model is optimized for the connectors shown on the pictures. Super glue/cyano acrylate/any other transparent fast setting glue which adheres to your filament. Wire (should be thick enough for 700 mA and thin enough to fit into the carrier ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

This is a procedure to prevent the bottom part of the model from collapsing. (a.k.a. elephant foot)  7. Nothing is attached to the top of the Z-axis frame yet. Do...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

We successfully engineered an incredibly stable and secure mounting arrangement by adjusting the RC roof rack's structural reinforcement through computer-aided engineering models. By applying advanced design methodologies, our innovative product not...

These two parts are rather small but also simple ball joint parts that rely on friction and cannot be tightened. For those of you that want a to be able to tightly secure your camera in a certain position, there are also parts that form a double-ball...

It can support itself and needs a lot more force to be bended. If you still want to print your own loc line, I used the models from MinyMan644 found here -> Loc-Line Fittings (1/4", 1/2" and 3/4"). I strongly recommend buying loc line instead of...

...The design is optimized for the given print orientation - no need to rotate the STL model.You will also need two of the strain relief clips, which I have provided as a separate project.Assembly6 pieces of M3 nuts have to be pressed into the plastic.

Check out my compatible Cable Hook. Also check out the <a href="https://www.thingiverse.com/tag:modular_mount">#modular_mount</a> and <a href="https://www.thingiverse.com/tag:MMs">#MMs</a> tags to find compatible...

DO NOT LOOK AT THE SUN WITH THIS!Also have a look at my improved Dobsonian Design:https://www.printables.com/model/317112-propdob-telescope-foldable-travel-dobsonian-45-mir&nbsp;Hi, this is a Newtonian telescope with a 114 mm diameter mirror and...

Cap for benq projector lenses, designed for the mx660 model. It fits perfectly. On the outside it has the logo of benq and on the inside that of ho-kago tea time (musical group from the anime k-on). This projector did not have the cover when I took...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

Post-Printing // model: Prusa i3 MK3 Y Chassis Bearing Straps // This replaces the zip ties that tend to stretch and can reduce accuracy over time. Optionally, also replace the entire strap and bearing with a 1-piece printed version that has been...

Finally you should set up channel mixing for tracked models in your transmitter. I added 2 photos of my mixer setup, but this video here explains it very well: https://tinyurl.com/bdns4pj5 It took me half an hour of trial&error negating channels...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

... with any light color and use a permanent black marker for the text. These models are not designed for dual-color printing. You'll need to print two Monster Ability Card holder v1. ...One is for the Monster cards, the other is for the shop cards.</p>

I have not included the CAD model: As a newbie, I made a fair mess of things whilst modding along and fear that the kind people of Autodesk would take away my Fusion hobby license:)That's it!DOWNLOAD NOW for limited access to the crack attachment:) A...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

First, I had to model the front of the display to accommodate the RepRap Discount Full Graphics Smart Controller and then I also decided it needed a back to protect the circuit board. Done... Then I decided to tackle the problem of mounting a...