ender 3 s1 pro upgrades 3d models

This is a remix of a previous S1 Pro Camera mount and a flex arm camera mount that I meshed together to get more of what I needed.Original Mount: https://www.thingiverse.com/thing:5396885 Original Flex Arm:...

Although I've only tested this on the S1 Pro, it should also work on the S1 and the S1 Plus, as I believe they all share the same gantry design. You'll need either 8x 10mmx2mm or 4x 10mmx4mm neodymium magnets for this. As strong as you can get...

Bed leveling fix for Ender 3 S1 models.Follow word doc instructions or reposition ABL using provided filesDoc source: https://www.facebook.com/groups/602529180853579/permalink/723427122097117/?fs=e&s=clThe following can be done with custom firmware...

This is the remix for https://www.thingiverse.com/thing:3209211 with stock S1 / S1 Pro mount.

It all depends on the time 😄---Reinforced part to fix the "Nema 17" motors of the Z axis on Creality Ender 3 S1 and S1 PRO printers as well as for other printer models that use a 40/20 aluminum extrusion profile.I created this reinforced part...

*This is a remix of [this design on Printables](https://www.printables.com/model/475690-ender-s1-gantry-light-bar).* --- This is a printable light bar support that screws into the existing hex screws at the back of the gantry, no additional screws...

Took some time to find a way and place to mount a usable wipe brush, as no existing designs fit this S1 Pro, Especially with the cable protector mod as this limits your X max travel due to cable length. Uses common wire brush available from...

Turn each stepper until they are both equally snug / compressed between the X axis extrusion and the top of the S1 Pro base plate. Tighten down your grub screws and make sure they are sandwiched properly against their pulleys. Also ensure the...

A corner piece that fits into the S1 Pro with a mount point on top that can be used for a columnto mount a camera or any other accessory you might need. You just take off the two scews pop the part in and put the screws back. Also added a simple...

Ender 3s1pro cam mount

This is actually not a remix, but an Add-On for S1 Pro owners who whant to use the "remixed" cable solution. With this way of cable management, when you print tall objects, the cable needs some extra space exactly where the light fixture is. So I...

https://www.printables.com/de/model/417892-ender-3-s1-pro-heating-bed-cable-chainholder Prevents cable breakage at the housing outlet and rubbing on the Y-axis motor. It can be attached to the underside of the housing and to the recess for the...

... just stops the annoying glare from hitting your eyes.  it does not affect platform lighting at all unfortunately the part is too long for an ender 3 bed so ull  need to print this model twice print is as simple as it gets no infill no support enjoy

It's a remix from https://www.thingiverse.com/thing:5953410, but much stronger because my cable is harder than on the regular S1 printer.And also on my design is lot more space for cables.But the idea of the original design was very good and now it...

COPY OF LINK BELOW - Printed for my Ender 5 S1 - Works Great https://www.thingiverse.com/thing:5345559

Made 3 extra version with different angles to accomodate for different viewing angles, original one was the 50° version, the printed one on display here is the 60° Extra I recommend printing sideways (the way the STLs come) with tree supports. i...

2023.3.6 UP DATE Added Rod riser clip 10mmRise ＆ 15mmRise Replace mounting bolts with M3x8mm bolts. Use M3x10mm bolts for knobs. The thickness of the mounting portion of the dial gauge is 8mm. Use extension rods. ... 【注意】 ...

(können auch 3 x 16mm sein) An diese Halterung kann auch die Filament Sensor Halterung von https://www.thingiverse.com/thing:5419960 angebracht werden. EN: I don't like it when the filament roll holder is attached to the printer boom. So I...

It is necessary to purchase this for easier assembly...

Drawer_pi3_v1 is just the remixed part to fit the pi 3 Drawer_pi3_withwirecutoutsandgrill is it with wire cutouts and a grill for airflow Drawerreceded is the same as the one above except the pi is pushed back so that the ports aren't exposed. It...

Layer and hotend fan mod, for ender 3 s1 or for printers using the sprite extruder. The mod is height adjustable. New closed ventilation duct V4, avoid leakage outside the printing area thanks to a rear cover that joins the duct behind the hotend.

I made it so it would fit to the left of the clip on spool holder on the S1/S1 Pro. You will have to remove some screws to get it slid in the slot, but its quite easy. My printer printed the hole a little tight on my original measurements so I scaled...

I could not find a simple holder for a scraper and cutter, for the s1/s1pro printers, so I made my own.

Hier ein Druck Profil für den Ender 3 S. Genutzt wurde ein Bambustudio Fork der zum Download hier mit bereit steht. Genutzt für Klipper falls ihr Marlin nutzt müsst ihr die Geschwindigkeiten anpassen. ...

So My S1 Pro hot bed cable fried on me while trying to utilize the entire bed. When the Bed is all the way forward (towards me) the cable that goes into the base housing is super tight and apparently after a few days of printing like this caused one...

ENDER 3 PRO UPGRADE HOTEND

This is a collection of my "heavly remixed" upgrades for ender 3 pro. I really liked the idea behind the cable chain maded by NG_Designs ; https://www.thingiverse.com/thing:3769941 but i decided to redesign it because it's really hard and long to...

This is a 5015 circular fan duct upgrade to Creality's ender 3 S1/Pro or  Creality's Sprite extruders.Here is it in action: ChangeLog-Fixed mounting Issue-Better Airflow-Added new mounting points for more rigidity-added overall...

Fits confirmed by users (without guarantee): Ender 3 Ender 3 Pro Ender 3 V2 Ender 3 S1 Ender 3 S1 Pro Ender 3 Max Neo Ender 5 Creality CR-10 Voxelab Aquila v2 Update V2: As suggested in the comments by...

Ender-3 S1 Pro control panel mount